Fluid Mechanics Fundamentals And Applications
3rd Edition
ISBN: 9780073380322
Author: Yunus Cengel, John Cimbala
Publisher: MCGRAW-HILL HIGHER EDUCATION
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 12, Problem 93P
To determine
The temperature at exit of duct.
The Mach number at the exit of duct.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Air enters a rectangular duct at T₁ = 300 K, P₁ = = 420 kPa, and Ma₁ = 2. Heat is transferred to the air in the = amount of 55 kJ/kg as it flows through the duct. Disregarding frictional losses, determine the temperature and Mach number at the duct exit.
Q1
Question Four
Air flows steadily adiabatically through a pipe with a cross-sectional of 0.002 m?. At the inlet of the
duct, the pressure and temperature are 100 kPa and 50°C, respectively. At the exit of the duct, the
temperature and velocity are 100°C and 600 m/s, respectively. Determine the Mach number and the
velocity at the inlet section. Also, calculate the mass flow rate. Ans. M 1.884, vi = 678.7 m/s,
m = 1.46 kg/s.
Chapter 12 Solutions
Fluid Mechanics Fundamentals And Applications
Ch. 12 - What is dynamic temperature?Ch. 12 - Prob. 4PCh. 12 - Prob. 5PCh. 12 - Calculate the stagnation temperature and pressure...Ch. 12 - Prob. 7PCh. 12 - Prob. 8EPCh. 12 - Prob. 9PCh. 12 - Products of combustion enter a gas turbine with a...Ch. 12 - Is it possible to accelerate a gas to a supersonic...Ch. 12 - Prob. 18P
Ch. 12 - Prob. 28PCh. 12 - Prob. 39PCh. 12 - Prob. 41EPCh. 12 - Prob. 64PCh. 12 - Air enters a converging—diverging nozzle with low...Ch. 12 - Prob. 75EPCh. 12 - Prob. 76EPCh. 12 - Prob. 78PCh. 12 - Prob. 79PCh. 12 - Prob. 80CPCh. 12 - On a T-s diagram of Raleigh flow, what do the...Ch. 12 - What is the effect of heat gain and heat toss on...Ch. 12 - Prob. 83CPCh. 12 - Prob. 84CPCh. 12 - Prob. 85CPCh. 12 - Argon gas enters a constant cross-sectional area...Ch. 12 - Prob. 87PCh. 12 - Prob. 88PCh. 12 - Prob. 89PCh. 12 - Prob. 90EPCh. 12 - Prob. 92EPCh. 12 - Prob. 93PCh. 12 - Prob. 94PCh. 12 - Prob. 95PCh. 12 - Prob. 96PCh. 12 - Prob. 97CPCh. 12 - Prob. 98CPCh. 12 - Prob. 99CPCh. 12 - Prob. 100CPCh. 12 - Prob. 101CPCh. 12 - Prob. 102CPCh. 12 - Prob. 103CPCh. 12 - Prob. 104CPCh. 12 - Air enters a 12-cm-diameter adiabatic duct at...Ch. 12 - Air enters a 15-m-long, 4-cm-diameter adiabatic...Ch. 12 - Air enters a 5-cm-diameter, 4-m-long adiabatic...Ch. 12 - Helium gas with k=1.667 enters a 6-in-diameter...Ch. 12 - Air enters a 15-cm-diameter adiabatic duct with...Ch. 12 - Air flows through a 6-in-diameter, 50-ft-long...Ch. 12 - Air in a room at T0=300k and P0=100kPa is drawn...Ch. 12 - Prob. 115PCh. 12 - Prob. 116PCh. 12 - Prob. 117PCh. 12 - Prob. 118PCh. 12 - Prob. 119PCh. 12 - Prob. 120PCh. 12 - Prob. 121PCh. 12 - Prob. 122PCh. 12 - A subsonic airplane is flying at a 5000-m altitude...Ch. 12 - Prob. 124PCh. 12 - Prob. 125PCh. 12 - Prob. 126PCh. 12 - Prob. 128PCh. 12 - Prob. 129PCh. 12 - Prob. 130PCh. 12 - An aircraft flies with a Mach number Ma1=0.9 at an...Ch. 12 - Prob. 132PCh. 12 - Helium expands in a nozzle from 220 psia, 740 R,...Ch. 12 - Prob. 136PCh. 12 - Prob. 137PCh. 12 - Prob. 138PCh. 12 - Prob. 139PCh. 12 - Prob. 140PCh. 12 - Prob. 141PCh. 12 - Prob. 142PCh. 12 - Prob. 143PCh. 12 - Prob. 144PCh. 12 - Prob. 145PCh. 12 - Prob. 146PCh. 12 - Prob. 147PCh. 12 - Air is cooled as it flows through a 30-cm-diameter...Ch. 12 - Prob. 149PCh. 12 - Prob. 152PCh. 12 - Prob. 155PCh. 12 - Prob. 156PCh. 12 - Prob. 157PCh. 12 - Prob. 158PCh. 12 - Prob. 159PCh. 12 - Prob. 160PCh. 12 - Prob. 161PCh. 12 - Prob. 162PCh. 12 - Prob. 163PCh. 12 - Prob. 164PCh. 12 - Assuming you have a thermometer and a device to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate for a back pressure of 0 kPa. q = 250 kJ/kg P. = 500 kPa T, = 500°C Po = 0 kPa D = 0.02marrow_forwardn aircraft is flying at an altitude of 12000 metres (T=216.65 K. p = 0.193 bar) at a Mach number of 0.82. The cross sectional area of the inlet diffuser before the L.P. compressor stage is 0.5 m. Determine (a) the mass of air entering the compressor per second (b) the speed of the aircraft (c) the stagnation %3D pressure and temperature of air at the diffuser entry.arrow_forwardQ.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate for a back pressure of 0 kPa. q = 250 kJ/kg Pr = 500 kPa Tr = 500°C Po = 0 kPa D= 0.02marrow_forward
- The velocity ratio(v1/v2)of an isentropic flow through a supersonic wind tunnel is 0.915 ifthe velocity and mach number at the exit are 376.95 m/s and 2.60 respectively find the value of speed of sound at the entrancearrow_forwardAir enters a rectangular duct at T1 = 285 K, P1 = 390 kPa, and Ma1 = 2. Heat is transferred to the air in the amount of 55 kJ/kg as it flows through the duct. Disregarding frictional losses, determine the temperature and Mach number at the duct exit.arrow_forwardAir enters a nozzle that has an inlet area of 0.4 m?, at 200 kPa, 500 °C. and 30 m/s. At the exit the conditions are 100 kPa and 443 °C. Part A If the exit area is 45 cm? , determine the steady-state exit velocity. Use the IG flow-state TESTcalc. Express the steady-state exit velocity in meters per second to four significant figures. ΑΣφ vec ? V. = m/s Submit Request Answerarrow_forward
- Fluid mechanical A large vessel contains compressed air at To = 350 K and Po = 2 bar. A converging-diverging nozzle is attached to the vessel to discharge air. The throat area of the nozzle is 200 cm2. At the exit, the pressure is 20 kPa and the flow is supersonic. Answer the followings: The mass flow rate of the air = Mach number at exit = he exit are = Air velocity at exit Air velocity at throat = Air pressure at throat =arrow_forwardaircraft flies at the same Mach number but 50 m/s slower at 8 km compared to its speed at sea level. Find this Mach number a. 1.45 b. 1.55 c. 2.25 d. 1.65 e. 2.50.arrow_forwardAir flows through a converging-diverging (c-d) nozzle. It is supplied from a large air reservoir in which the temperature is 446 K and the pressure is 190 kPa. The velocity and the cross-sectional area at the nozzle exit are 594 m/s and 0.0005 m^2, respectively. Find the followings: Mach number at exit is Area of the throat is The mass flow rate of air is The exit temperature is The exit pressure isarrow_forward
- Q.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate for a back pressure of 0 kPa. q= 250 kJ/kg P.= 500 kPa T; = 500°C p. = 0 kPa D=0.02marrow_forwardCan you solve this question in 20min please?!!arrow_forwardAir at 30 lbf/in2 absolute and 200F flows from a reservoir into a duct. The flow is steady, adiabatic, frictionless. The flow rate is 10lbm/s. What are the cross-sectional area, temperature, pressure, and Mach number at the point in the duct where the velocity is 1,400 ft/s?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License