Fluid Mechanics Fundamentals And Applications
3rd Edition
ISBN: 9780073380322
Author: Yunus Cengel, John Cimbala
Publisher: MCGRAW-HILL HIGHER EDUCATION
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 12, Problem 147P
To determine
The velocity, temperature, and pressure at the duct exit.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Helium is heated as it flows subsonically through a 10 cm × 10 cm square duct. The properties of helium at the inlet are maintained at Ma1 = 0.6, P1 = 350 kPa, and T1 = 420 K at all times. Disregarding frictional losses, determine the highest rate of heat transfer to the air in the duct without affecting the inlet conditions.
Problem 5. Air flows steadily and adiabatically from a large tank at a stagnation pressure of Po1 = 10 bar and
stagnation temperature of To = 400 K through a frictionless converging nozzle and into a constant-area pipe with a
diameter of D = 0.10 m and an average friction factor of f = 0.30. At Section (1) at the nozzle exit (or duct inlet), the
absolute pressure is P1 = 8.0 bar. At Section (2) at the duct exit, the absolute pressure is P1 = 5.0 bar. (a) Determine
the Mach numbers and temperatures at Section (1) and Section (2). (b) Determine the critical length and the length of
pipe from Section (1) and Section (2). (c) Sketch the T-s diagram for flow from large tank to Section (2). (d) Briefly discuss
what will happen if the length of the pipe is increased with fixed Po1 and To.
Air is heated as it flows subsonically through a duct. When the amount of heat transfer reaches 67 kJ/kg, the flow is observed to be choked, and the velocity and the static pressure are measured to be 680 m/s and 270 kPa. Disregarding frictional losses, determine the velocity, static temperature, and static pressure at the duct inlet.
Chapter 12 Solutions
Fluid Mechanics Fundamentals And Applications
Ch. 12 - What is dynamic temperature?Ch. 12 - Prob. 4PCh. 12 - Prob. 5PCh. 12 - Calculate the stagnation temperature and pressure...Ch. 12 - Prob. 7PCh. 12 - Prob. 8EPCh. 12 - Prob. 9PCh. 12 - Products of combustion enter a gas turbine with a...Ch. 12 - Is it possible to accelerate a gas to a supersonic...Ch. 12 - Prob. 18P
Ch. 12 - Prob. 28PCh. 12 - Prob. 39PCh. 12 - Prob. 41EPCh. 12 - Prob. 64PCh. 12 - Air enters a converging—diverging nozzle with low...Ch. 12 - Prob. 75EPCh. 12 - Prob. 76EPCh. 12 - Prob. 78PCh. 12 - Prob. 79PCh. 12 - Prob. 80CPCh. 12 - On a T-s diagram of Raleigh flow, what do the...Ch. 12 - What is the effect of heat gain and heat toss on...Ch. 12 - Prob. 83CPCh. 12 - Prob. 84CPCh. 12 - Prob. 85CPCh. 12 - Argon gas enters a constant cross-sectional area...Ch. 12 - Prob. 87PCh. 12 - Prob. 88PCh. 12 - Prob. 89PCh. 12 - Prob. 90EPCh. 12 - Prob. 92EPCh. 12 - Prob. 93PCh. 12 - Prob. 94PCh. 12 - Prob. 95PCh. 12 - Prob. 96PCh. 12 - Prob. 97CPCh. 12 - Prob. 98CPCh. 12 - Prob. 99CPCh. 12 - Prob. 100CPCh. 12 - Prob. 101CPCh. 12 - Prob. 102CPCh. 12 - Prob. 103CPCh. 12 - Prob. 104CPCh. 12 - Air enters a 12-cm-diameter adiabatic duct at...Ch. 12 - Air enters a 15-m-long, 4-cm-diameter adiabatic...Ch. 12 - Air enters a 5-cm-diameter, 4-m-long adiabatic...Ch. 12 - Helium gas with k=1.667 enters a 6-in-diameter...Ch. 12 - Air enters a 15-cm-diameter adiabatic duct with...Ch. 12 - Air flows through a 6-in-diameter, 50-ft-long...Ch. 12 - Air in a room at T0=300k and P0=100kPa is drawn...Ch. 12 - Prob. 115PCh. 12 - Prob. 116PCh. 12 - Prob. 117PCh. 12 - Prob. 118PCh. 12 - Prob. 119PCh. 12 - Prob. 120PCh. 12 - Prob. 121PCh. 12 - Prob. 122PCh. 12 - A subsonic airplane is flying at a 5000-m altitude...Ch. 12 - Prob. 124PCh. 12 - Prob. 125PCh. 12 - Prob. 126PCh. 12 - Prob. 128PCh. 12 - Prob. 129PCh. 12 - Prob. 130PCh. 12 - An aircraft flies with a Mach number Ma1=0.9 at an...Ch. 12 - Prob. 132PCh. 12 - Helium expands in a nozzle from 220 psia, 740 R,...Ch. 12 - Prob. 136PCh. 12 - Prob. 137PCh. 12 - Prob. 138PCh. 12 - Prob. 139PCh. 12 - Prob. 140PCh. 12 - Prob. 141PCh. 12 - Prob. 142PCh. 12 - Prob. 143PCh. 12 - Prob. 144PCh. 12 - Prob. 145PCh. 12 - Prob. 146PCh. 12 - Prob. 147PCh. 12 - Air is cooled as it flows through a 30-cm-diameter...Ch. 12 - Prob. 149PCh. 12 - Prob. 152PCh. 12 - Prob. 155PCh. 12 - Prob. 156PCh. 12 - Prob. 157PCh. 12 - Prob. 158PCh. 12 - Prob. 159PCh. 12 - Prob. 160PCh. 12 - Prob. 161PCh. 12 - Prob. 162PCh. 12 - Prob. 163PCh. 12 - Prob. 164PCh. 12 - Assuming you have a thermometer and a device to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Problem 5. Air flows steadily and adiabatically from a large tank at a stagnation pressure of P01 = 10 bar and stagnation temperature of To = 400 K through a frictionless converging nozzle and into a constant-area pipe with a diameter of D = 0.10 m and an average friction factor of f = 0.30. At Section (1) at the nozzle exit (or duct inlet), the absolute pressure is p₁ = 8.0 bar. At Section (2) at the duct exit, the absolute pressure is P1 = 5.0 bar. (a) Determine the Mach numbers and temperatures at Section (1) and Section (2). (b) Determine the length of pipe from Section (1) to Section (2). (c) Sketch the T-s diagram for flow from large tank to Section (2). (d) Briefly discuss what will happen if the length of the pipe is increased with fixed p01 and To.arrow_forwardIn compressible flow, velocity measurements with a Pitot probe can be grossly in error if relations developed for incompressible flow are used. Therefore, it is essential that compressible flow relations be used when evaluating flow velocity from Pitot probe measurements. Consider supersonic flow of air through a channel. A probe inserted into the flow causes a shock wave to occur upstream of the probe, and it measures the stagnation pressure and temperature to be 620 kPa and 340 K, respectively. If the static pressure upstream is 110 kPa, determine the flow velocity.arrow_forwardAir enters a 5-cm-diameter, 4-m-long adiabatic duct with inlet conditions of Ma1 = 2.8, T1 = 380 K, and P1 = 80 kPa. It is observed that a normal shock occurs at a location 3 m from the inlet. Taking the average friction factor to be 0.007, determine the velocity, temperature, and pressure at the duct exit.arrow_forward
- Air is heated as it flows subsonically through a 5 cm × 10 cm duct. The properties of air at the inlet are maintained at Ma1 = 0.6, P1 = 350 kPa, and T1 = 420 K at all times. Disregarding frictional losses, determine the highest rate of heat transfer to the air in the duct without affecting the inlet conditions. Take the properties of air to be k = 1.4, cp = 1.005 kJ/kg·K, and R = 0.287 kJ/kg·K. The highest rate of heat transfer to the air in the duct is___ kW.arrow_forwardn aircraft is flying at an altitude of 12000 metres (T=216.65 K. p = 0.193 bar) at a Mach number of 0.82. The cross sectional area of the inlet diffuser before the L.P. compressor stage is 0.5 m. Determine (a) the mass of air entering the compressor per second (b) the speed of the aircraft (c) the stagnation %3D pressure and temperature of air at the diffuser entry.arrow_forwardAir flows through a long, isentropic nozzle. The temperature and pressure at the * reservoir are 1000K and 20 atm, respectively. If the Mach number at the entrance is 0.2, determine the gas velocity at the entrance. 634 m/s 127 m/s 478 m/s 254 m/s For a large centrifugal pump, the required net positive suction head is typically around 5 ft 2 ft 15 ftarrow_forward
- Air at 26 psia, 320°F, and Mach number Ma = 0.7 flows through a duct. Calculate the velocity and the stagnation pressure, temperat and density of air. The properties of air are R = 0.06855 Btu/lbm-R = 0.3704 psia-ft3/lbm-R and k=1.4. The velocity of air is ft/s. The stagnation temperature of air is The stagnation pressure of air is The stagnation density of air is R. psia. | lbm/ft³.arrow_forwardAir (y = 1.4 andR= 0.287 kJ/kg ·K) enters a constant-area insulated duct with a Mach number of 0.35, a stagnation pressure of 105 kPa, and stagnation temperature of 300 K. For a duct length of 50 cm, duct diameter of 1 cm, and friction coefficient of 0.022, determine pressure and velocity at the inlet and outlet sections and the mass flow rate of the air.arrow_forwardstagi 900 kPa 1- Air enters a compressor for a mass flow rate of 0.04 kg/s. at a stagnation temperature 358 K. Assuming the AIR compression process to be isentropic, determine the power 0.04 kg/s require. 100 kPa stagnationarrow_forward
- The friction factor for a 25 mm diameter11.5 m long pipe is 0.004. The conditions of air at entry are P1 = 2.0 bar, T= 301 K, M=0.25 Determine the mass flow rate, and the pressure, temperature and the Mach number at exit.arrow_forwardArgon gas enters a constant cross-sectional area duct at Ma1 = 0.2, P1 = 320 kPa, and T1 = 400 K at a rate of 0.85 kg/s. Disregarding frictional losses, determine the highest rate of heat transfer to the argon without reducing the mass flow rate.arrow_forwardCompressed air from the compressor of a gas turbine enters the combustion chamber at T1 = 700 K, P1 = 560 kPa, and Ma1 = 0.2 at a rate of 0.3 kg/s. Via combustion, heat is transferred to the air at a rate of 300 kJ/s as it flows through the duct with negligible friction. Determine the Mach number at the duct exit and the drop in stagnation pressure P01 – P02 during this process. Take the properties of air to be k = 1.4, cp = 1.005 kJ/kg·K, and R = 0.287 kJ/kg·K. The Mach number at the duct exit is____ . The drop in stagnation pressure is____ kPa.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License