Fluid Mechanics Fundamentals And Applications
3rd Edition
ISBN: 9780073380322
Author: Yunus Cengel, John Cimbala
Publisher: MCGRAW-HILL HIGHER EDUCATION
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 12, Problem 114P
Air in a room at
FIGURE P12-109
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Air in a room at T0= 290 K and P0= 95 kPa isdrawn steadily by a vacuum pump through a 1-cm-diameter,50-cm-long adiabatic tube equipped with a converging nozzleat the inlet. The flow in the nozzle section can be assumed tobe isentropic, and the average friction factor for the duct canbe taken to be 0.018. Determine the maximum mass flow rate of air that can be sucked through this tube and the Machnumber at the tube inlet.
A pump increases the water pressure from 70 kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 45 oC through a 1.5 cm diameter opening and exits
through a 2.1 cm diameter opening. Determine the velocity of the water at the (a) inlet and (b) outlet when the mass flow rate through the pump is 1.4 kg/s.
Submit your solution by multiplying (a)*(b) =
Format answer : 46.84
Submit
use direct formula
Chapter 12 Solutions
Fluid Mechanics Fundamentals And Applications
Ch. 12 - What is dynamic temperature?Ch. 12 - Prob. 4PCh. 12 - Prob. 5PCh. 12 - Calculate the stagnation temperature and pressure...Ch. 12 - Prob. 7PCh. 12 - Prob. 8EPCh. 12 - Prob. 9PCh. 12 - Products of combustion enter a gas turbine with a...Ch. 12 - Is it possible to accelerate a gas to a supersonic...Ch. 12 - Prob. 18P
Ch. 12 - Prob. 28PCh. 12 - Prob. 39PCh. 12 - Prob. 41EPCh. 12 - Prob. 64PCh. 12 - Air enters a converging—diverging nozzle with low...Ch. 12 - Prob. 75EPCh. 12 - Prob. 76EPCh. 12 - Prob. 78PCh. 12 - Prob. 79PCh. 12 - Prob. 80CPCh. 12 - On a T-s diagram of Raleigh flow, what do the...Ch. 12 - What is the effect of heat gain and heat toss on...Ch. 12 - Prob. 83CPCh. 12 - Prob. 84CPCh. 12 - Prob. 85CPCh. 12 - Argon gas enters a constant cross-sectional area...Ch. 12 - Prob. 87PCh. 12 - Prob. 88PCh. 12 - Prob. 89PCh. 12 - Prob. 90EPCh. 12 - Prob. 92EPCh. 12 - Prob. 93PCh. 12 - Prob. 94PCh. 12 - Prob. 95PCh. 12 - Prob. 96PCh. 12 - Prob. 97CPCh. 12 - Prob. 98CPCh. 12 - Prob. 99CPCh. 12 - Prob. 100CPCh. 12 - Prob. 101CPCh. 12 - Prob. 102CPCh. 12 - Prob. 103CPCh. 12 - Prob. 104CPCh. 12 - Air enters a 12-cm-diameter adiabatic duct at...Ch. 12 - Air enters a 15-m-long, 4-cm-diameter adiabatic...Ch. 12 - Air enters a 5-cm-diameter, 4-m-long adiabatic...Ch. 12 - Helium gas with k=1.667 enters a 6-in-diameter...Ch. 12 - Air enters a 15-cm-diameter adiabatic duct with...Ch. 12 - Air flows through a 6-in-diameter, 50-ft-long...Ch. 12 - Air in a room at T0=300k and P0=100kPa is drawn...Ch. 12 - Prob. 115PCh. 12 - Prob. 116PCh. 12 - Prob. 117PCh. 12 - Prob. 118PCh. 12 - Prob. 119PCh. 12 - Prob. 120PCh. 12 - Prob. 121PCh. 12 - Prob. 122PCh. 12 - A subsonic airplane is flying at a 5000-m altitude...Ch. 12 - Prob. 124PCh. 12 - Prob. 125PCh. 12 - Prob. 126PCh. 12 - Prob. 128PCh. 12 - Prob. 129PCh. 12 - Prob. 130PCh. 12 - An aircraft flies with a Mach number Ma1=0.9 at an...Ch. 12 - Prob. 132PCh. 12 - Helium expands in a nozzle from 220 psia, 740 R,...Ch. 12 - Prob. 136PCh. 12 - Prob. 137PCh. 12 - Prob. 138PCh. 12 - Prob. 139PCh. 12 - Prob. 140PCh. 12 - Prob. 141PCh. 12 - Prob. 142PCh. 12 - Prob. 143PCh. 12 - Prob. 144PCh. 12 - Prob. 145PCh. 12 - Prob. 146PCh. 12 - Prob. 147PCh. 12 - Air is cooled as it flows through a 30-cm-diameter...Ch. 12 - Prob. 149PCh. 12 - Prob. 152PCh. 12 - Prob. 155PCh. 12 - Prob. 156PCh. 12 - Prob. 157PCh. 12 - Prob. 158PCh. 12 - Prob. 159PCh. 12 - Prob. 160PCh. 12 - Prob. 161PCh. 12 - Prob. 162PCh. 12 - Prob. 163PCh. 12 - Prob. 164PCh. 12 - Assuming you have a thermometer and a device to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In a place where the outdoor air temperature is 30°C, the air is compressed from its current temperature to 800 kPa pressure continuously and isothermally.The flow rate of the air is 1.5 kg/second.Since the compressor works with 60% efficiency;(a) how much power must be supplied to the compressor?(b) calculate the outlet temperature of the air?arrow_forwardA pump increases the water presssure from 8kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 41.51 degrees celsius through a 1.145-cm-diameter opening and exits through a 2.821-cm-diameter opening. Determine the velocity of the water at the outlet in m/s when the mass flow rate through the pump is 1.354kg/s. The specific volume of incoming water is 1.547x10-3m3/kg.arrow_forwardThe enthalpy drop of steam across a nozzle is found to be 165 kJ/kg. The increase in velocityarrow_forward
- Water at the initial pressure of 1 atm and temperature of 15C is flowing through a pump. Final pressure of water is 900 kPa at the outlet. Water enters through a 1-cm-diameter opening and exits through a 2.5-cm- diameter opening. Determine the velocity of the water at the inlet and outlet when the mass flow rate through the pump is 0.5 kg/s.arrow_forwardAir enters an electric furnace at 100 KPa and 28°C with a volume flow rate of 22 m3/min. At the exit of the furnace, the air is 100 KPa and 50°C. The air passes through a ducting system consisting of three branches, one duct with 30cm diameter and the other two with 16cm diameter. If the velocity of air in the 16cm ducting was measured to be 3.7 m/s, determine the mass flow arte in kg/s of air entering the furnace and the velocity in m/s of air in the 30cm duct.arrow_forwardA steam turbine is used to generate electric power in a small-scale process industry. The turbine receives superheated steam at 12.5 MPa absolute pressure and 700°C Superheated Steam temperature. It rejects the exhaust steam as saturated vapor at 1000 kPa absolute pressure. Wout The mass flow rate of the steam while flowing through the turbine is 10.5 kg/sec. Steam Turbin e The outlet pipe diameter is 18 cm. Saturated Vapor Note: • Neglect the changes in the kinetic and potential energies Neglect the heat losses from the turbine • The specific enthalpy of steam at the inlet of the turbine is approximately equal to |kJ/kg • The specific enthalpy of steam at the outlet of the turbine is approximately equal to kJ/kg • The specific volume of the steam at the outlet of the turbine is approximately equal to m3/kg • The density of the steam at the outlet of the turbine is approximately equal to kg/m3 • The (absolute) work developed by turbine is approximately equal to kW • The exit velocity…arrow_forward
- Q1/Steam at (5 MPa and 400°C) enters a nozzle steadily with a velocity of 80 m/s, and it leaves at (2 MPa and 300°C). The inlet area of the nozzle is (50 cm2). Determine (a) the mass flow rate of the steam, (b) the exit velocity of the steam,arrow_forwardAn Ideal gas is being heated in a circular duct as while flowing over an electric heater of 130 kW. The diameter of duct is 500 mm. The gas enters the heating section of the duct at 100 kPa and 27 deg C with a volume flow rate of 15 m3/s. If heat is lost from the gas in the duct to the surroundings at a rate of 80 kW, Calculate the exit temperature of the gas in deg C. (Assume constant pressure, ideal gas, negligible change in kinetic and potential energies and constant specific heat; Cp =1000 J/kg K; R = 500 J/kg K)arrow_forward(6) Steam enters a nozzle at 900°C and 2500 kPa with a velocity of 12 m/s, and leaves at 800°C and 1800 kPa. If the inlet area of the nozzle is 975 cm?, the volume flow rate of the steam at the exit (in L/s) is: (а) 1450 (b) 1461 (с) 1473 (d) 1486 (e) 1499arrow_forward
- Refrigerant R-134a enters to the compressor of a refrigeration machine at a pressure of 140 kPa and a temperature of -10 °C, then comes out at a pressure of 1 MPa . Volumetric flow of the refrigerant entering the compressor 0.23 m3 /minute. Refrigerant enters throttling valve at 0.95 MPa pressure and 30 °C, and comes out the evaporator at -18 °C as saturated steam. Adiabatic efficiency of the compressor It is 78%. Show the cycle in the T-s diagram. Then calculate: a) Power required to run the compressor b) The heat withdrawn from the cooled environment in unit time, COPsm=? c)Between the evaporator and the compressor, pressure drop of the refrigerant and its heat gain.arrow_forwardWater with density ρ = 998 kg/m3, is flowing at steady mass flow rate through a uniform-diameter pipe. The entrance pressure of the fluid is 68.9 kPa in the pipe, which connects to a pump, which supplies 155.4 J/kg of fluid flowing in the pipe. The exit pipe from the pump is the same diameter as the inlet pipe. The exit section of the pipe is 3.05 m higher than the entrance, and the exit pressure is 137.8 kPa. The Reynolds number in the pipe is above 4,000 in this system. Calculate the frictional loss in the pipe system.arrow_forwardRefrigerant-134a enters an adiabatic compressor at 100 kPa and 0 "C with a volumetric flow rate of 0.3 m3/s and leaves at a pressure of 700 kPa. The power input to the compressor is 35 kW. Using the property tables for R-134a in Appendices A-11 to A-13, Determine the following stream properties and report them in the units shown and to the requested decimal place: A. The mass flow rate of the refrigerant: kg/s (Report to 3 decimal places, eg: 0.123) B. The enthalpy of the exit stream: KJ/kg (Report to 2 decimal places, eg: 0.23) C. The temperature of the exit stream: °C (Report to 1 decimal place, eg: 0.1) 100 KPa, 0°C V = 0.3 m³ /s %3D A A R-134 a 35 KW 700 KPaarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License