3: A steel plate of dimensions 2.5 x 1.2 x 0.1 m is hoisted by steel cables with lengths L₁ = 3.2 m and L₂ = 3.9 m that are each attached to the plate by a clevis and pin. The pins through the clevises are 18 mm in diameter and are located 2.0 m apart. The orientation angles are measured to be 0 94.4° and a = 54.9°. Density of steel is 77 kN/m³ and ignore the weight of the cables. 1. Find the average shear stress in pin 1 (MPa). 2. Find the average shear stress in pin 2 (MPa). 3. Calculate the average bearing stress between the steel plate and in pin 2 (MPa). ANSWERS: 25.9 MPa; 21.1 MPa; 5.99 MPa Clevis and 12 BB pin 1 2.0 m Clevis and pin 2 Center of mass of plate Steel plate (2.5 x 1.2x0.1/m)

3: A steel plate of dimensions 2.5 x 1.2 x 0.1 m is hoisted by steel cables with lengths L₁ = 3.2 m and L₂ = 3.9 m that are each attached to the plate by a clevis and pin. The pins through the clevises are 18 mm in diameter and are located 2.0 m apart. The orientation angles are measured to be 0 94.4° and a = 54.9°. Density of steel is 77 kN/m³ and ignore the weight of the cables. 1. Find the average shear stress in pin 1 (MPa). 2. Find the average shear stress in pin 2 (MPa). 3. Calculate the average bearing stress between the steel plate and in pin 2 (MPa). ANSWERS: 25.9 MPa; 21.1 MPa; 5.99 MPa Clevis and 12 BB pin 1 2.0 m Clevis and pin 2 Center of mass of plate Steel plate (2.5 x 1.2x0.1/m)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.22P: A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo...

See similar textbooks

Similar questions

i need answer typing clear urjent no chatgpt used i will give 5 upvotes
Two steel wires support a moveable overheadcamera weighing W = 28 lb (see fgure part a) usedfor close-up viewing of field action at sporting events.At some instant, wire 1 is at an angle α = 22° to thehorizontal and wire 2 is at angle β = 40°. Wires 1and 2 have diameters of 30 and 35 mils, respectively.(Wire diameters are often expressed in mils; one milequals 0.001 in.)(a) Determine the tensile stresses σ1 and σ2 in thetwo wires.(b) If the stresses in wires 1 and 2 must be the same,what is the required diameter of wire 1? (c) To stabilize the camera for windy outdoor conditions,a third wire is added (see figure part b).Assume the three wires meet at a common pointcoordinates (0, 0, 0) above the camera at theinstant shown in figure part b. Wire 1 is attachedto a support at coordinates (75 ft, 48 ft, 70 ft).Wire 2 is supported at (270 ft, 55 ft, 80 ft).Wire 3 is supported at (210 ft, 285 ft, 75 ft).Assume that all three wires have a diameter of30 mils. Find the tensile stresses in all…
The rod made of two different materials is fixed at point A. AB aluminum, BC steel It is made of materials. E1 = 70 Gpa and E2 = 210 Gpa. P = 100 kN axial compressive force It affects the C point. The diameter of the circular bars is D1 = 80 mm, D2 = 40 mm and their length L1 = 20 cm. and L2 = 30 cm. (The direction of the force P is in the negative x-axis direction.) a) What are the displacements at B and C points? b) What is the reaction force at point A? c) What are the stresses in the bar?
A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo is unloaded by a container handling crane. Each bollard is fastened to the wharf using anchor bolts. Three cables having known tension force magnitudes F, = ll0 kN.F, = 85kN.and F, 9OkNare secured to one bollard at a point A with coordinates (0.0.45 m. 0) in the x-r-: coordinate system shown in the figure part b. Each cable force is directed at an attachment point on the ship. Force F, is directed from point A to a point on the ship having coordinates (3 m, 9 m. 0) force F, is directed at a point with coordinates (6.5 m. 8.5 m. 2 m) and force F, is directed at a point with coordinates (8 m. 9 m. S m). The diameter of each anchor bolts is 4 24 mm. (a) Find the reaction forces and reaction moments at the base of the bollard. (b) Calculate the average shear stress in the anchor bolts (in the x-: plane). Assume each bolt cart ics an equal share of the total force.
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as floows; 48 kips tension in the x directio, 60 kips compression in the y direction, and 54 kips tension in the z direction. If v = 0.30 and E = 29 x 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
AB=1.2m BC=0.6m theta=25 phi=45 Vc=0.02
A force F of 40000 lbf is applied to rod AC the negative Y-direction. The rod is 1000 inches tall. A Force P of 25 lbf is applied in the negative Z- direction at point E, and a force R of 75 lbf is applied in the negative Z-direction at point F. Rod AC has a diameter of 1 inch from A to C, a diameter of 1.5 inches from B to C, and all fillet radii are 0.25 in. The rod is made of 1020 CD steel, and has a Sy of 135 ksi, a Sut of 150 ksi, and an ɛf = 0.15. Determine the effective stress at point B. 100 100 200 F. 800 B. 100 2D view of rod AC in XY plane
The Cylinder C in the Figure shown weighs 1000lb. Draw the FBD of cylinder C & of Rod AB
What is the over-turning moment at x = 0, of a hollow tube that has an OD of 40 mm, and an ID of 20 mm. The length of the tube is 960 mm. It is attached to a 1 inch thick plate.
A steel plate of dimensions 2.5 x 1.5 x 0.08 m and weighing 23.1 kN is hoisted by steel cables with lengths L1 = 3.2 m and L2 = 3.9 m that are each attached to the plate by a clevis and pin (see figure). The pins through the clevises are 18 mm in diameter and are located 2.0 m apart. The orientation angles are measured to be s = 94.4' and a = 54.9° For these conditions, first determine the cable forces T1 and T2, then find the average shear stress Taver in both pin 1 and pin 2, and then the average bearing stress ?? between the steel plate and each pin. Ignore the weight of the cables.
I got wrong answer last time I posted. Please do it correctly.
Hello sir, please, the solution and the solution line is as in books, I mean, not manual, please, sir, please, the line is as in books.