A wheel of diameter 150.0 mm and width 37.00 mm carrying a load 2.200 kN rolls on a flat rail. Take the wheel material as steel and the rail material as cast iron. Assume the figure given, which is based on a Poisson's ratio of 0.3, is applicable to estimate the depth at which the maximum shear stress occurs for these materials. At this critical depth, calculate the Hertzian stresses σr, σy, σz, and Tmax for the wheel. 1.0 0.8 0, т Ratio of stress to Pmax 0.4 0.6 90 69 0.2 0.5b b 1.5b Tmax 2b Distance from contact surface The Hertizian stresses are as follows: 02 = or = -23.8 psi for the wheel =| necessary.) σy for the wheel =| MPa σz for the wheel = MPa V4 for the wheel = | MPa 2.5b ཡི 3b MPa (Include a minus sign if

A wheel of diameter 150.0 mm and width 37.00 mm carrying a load 2.200 kN rolls on a flat rail. Take the wheel material as steel and the rail material as cast iron. Assume the figure given, which is based on a Poisson's ratio of 0.3, is applicable to estimate the depth at which the maximum shear stress occurs for these materials. At this critical depth, calculate the Hertzian stresses σr, σy, σz, and Tmax for the wheel. 1.0 0.8 0, т Ratio of stress to Pmax 0.4 0.6 90 69 0.2 0.5b b 1.5b Tmax 2b Distance from contact surface The Hertizian stresses are as follows: 02 = or = -23.8 psi for the wheel =| necessary.) σy for the wheel =| MPa σz for the wheel = MPa V4 for the wheel = | MPa 2.5b ཡི 3b MPa (Include a minus sign if

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
A rod of square 30x 30mm2cross-sectionsubject to a compressive axial force of 72kN and a twisting moment of 168.5N.m. Calculate the principal stresses and the maximum shear stress atthemostcritical point in the rod.
How do I calculate for sigma seam? Thank you
A shaft 450 mm diameter supports a 15000 kg steel propeller of the ship. The propeller shaft can be considered as a cantilever of 2 m length with a concentrated load at the end. The propeller is driven at 100 rpm when speed of the ship is 17.2 Knots. If the engine develops 15 MW and the propulsion efficiency is 85 %, calculate the principal stresses and the Maximum shear stress in the shaft and hence determine the factor of safety based on Max. shear stress and distortion energy theories if the shaft is made of steel having yield strength = 380 MPa. Given 1 knot = 1852 m/hr., sea water density = 1.1g/ml
Consider the 2-D state of stress shown below. Using the provided scales graph the Mohr's Circle for the 2-D state of stress with "full' details Draw the Planes of Principal and Maximum Shear Stresses Provide "full" details and Use 3 Sig. Fig. in this problem Oy = 15 Ksi Tcw → S Txy= -5 ksi Ox = 10 Ksi Tyx = 5 Ksi 10 5 -20 -10 5 10 15 20 5 10 Tccw → S'
Kindly solve this and show your solution
Please help with the stress, mohir circle, etc. Thank you
A stepped steel shaft is fixed to a wall at one end and subjected to torsion and axial loading as shown. The torque T=100 kip-in. Find the state of stress for two locations on the shaft: one between A and B and one between B and C. For each location, calculate the principal stresses and directions (i.e. the value of the angle 0). Draw the state of stress aligned with the principal directions. 12 in. 15 in. 2T A 6 in. B 4 in. C 125 kip
يم
A horizontal shaft of 75 mm diameter projects from a bearing, and in addition to the torque transmitted the shaft carries a vertical load of 8 kN at 300 mm from the bearing. If the safe stress for the material, as determined in a simple tension test, is 135 MN/m2, find the safe torque to which the shaft may be subjected using as the criterion (a) the maximum shearing stress, (b) the maximum strain energy per unit volume. Poisson’s ratio v = 0.29.[Ans: 5.05, 8.3 kN.m]
Indicate your assumptions, write the given and make an organized solution.
A shaft 30 mm diameter is transmitting power at a maximum shear stress of 80 MPa. If a pulley is connected to the shaft by means of a key,find the dimensions of key so that the stress in the key is not to exceed 50MPa and length of key is 4 times the width.