A condenser vacuum gauge reads 715 mmHg when the barometer stands at 757 mmHg. State the absolute pressure in the condenser in kN/m2 and bars.

Q: I asked this question last time. I saw this in an research paper I was reading. This initial…

A: Steps Involved Initialization of the State and Matrices:State Vector: The state vector will…

Q: very urgent i will give u like

A:

Q: The gears shown in the following figure have a module of 10 mm and a pressure angle of 20°. The…

A: Step 1:  Step 2: Step 3: Step 4:

Q:

A:

Q: correct the shaft misalignment in a cars transmission system, determine the offset distance required…

A: Detailed explanation:

Q: Sample Problem 2. The bowl-shaped device rotates about a vertical axis with a constant angular…

A: Step 1: Step 2: Step 3: Step 4:

Q: A mass and a spring system is subjected to an external harmonic excitation of 400cos20t (N). Find…

A:

Q: The parabolic cable running between the two transmission towers is carrying a uniformly distributed…

A:

Q: Q100 The following data refers to a test on a single-cylinder four-stroke oil engine Cylinder bore…

A:

Q: In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a…

A:

Q: Question: B10-4 This is a question based on the text book ‘’Mechanics of Materials’’ , please reply…

A:

Q: Design a Moore type synchronous state machine with three external inputs A1, A2, A3 and one output…

A: Step 1:

Q: During a visit to a plastic sheet factory, it is observed that a section of 45 mlength of a steam…

A:

Q: The parabolic cable running between the two transmission towers is carrying a uniformly distributed…

A:

Q: Examine Notes: Attempt Six Questions Only. rever necessa , Q1] (20 Marks) Answer with true (T) or…

A: The first statement is true. High chromium irons are indeed a type of grey cast iron that is alloyed…

Q: The answer to the problem is 2.71 ft/s. Please show me how to get the final answer

A:

Q: Q2:: Determine (Y). If Pa - PB = 6624 N m² Water Mercury 6Y B + Water

A: 1:  2:

Q: ut Ex. The cantilever beam shown is, made from steel with σ = 552 MPa is subjected to fully reversed…

A:

Q: 1. The bridge truss shown is supported by hinge at A and roller at H. Indicate “C” for compression…

A:

Q: (P + a V2 ? (VRT L ما تائب معة قرابة Pressure (atm) gal Ima find the units. atm. L I. m.k k atm L I…

A:

Q: ممكن الحل

A:

Q: Whats the true options of please

A:

Q: In the structure below, determine the forces that act on member BD and CD. The red arrows designate…

A: Step 1: Step 2: Step 3:

Q: Question: B07-5 This is a question based on the text book ‘’Mechanics of Materials’’ , please reply…

A:

Q: The robot has the same kinematics parameters as follows: Өл X4 Χι Joint 2 Link 2 a2 X3 Joint 3 03 d₁…

A:

Q: Collar B moves downward to the left with a constant velocity of 1.6 m/s and acceleration of 2 m/s²…

A:

Q: DONT USE ARTIFICIAL INTELLIGENCE

A: I hope this is helpful.

Q: The wide-flange shape W14 x 68 is used as a simple beam of 10-ft span. The beam is subjected to a…

A:

Q: An A-36 steel column has a length of 4 m and is pinned at both ends. If the cross sectional area has…

A: For any ReSolution or any doubt Let me know in comment section i will do it again and clear your…

Q: 20. [Ans. 9; 71.8 mm] A semi-elliptical laminated spring is made of 50 mm wide and 3 mm thick…

A: I hope this is helpful.

Q: Example(3): 0.15 kg/s steam at atmospheric pressure and superheated to 400 K is bled into an air…

A:

Q: A stainless steel canoe moves horizontally along the surface of a lake at 3.7 mi/h. TheThe lake's…

A: Step 1: Given Data: Velocity of the canoe (V): 3.7 mi/h Temperature of the water (T):  60∘F Length…

Q: s) Given a fixed sink temperature of 300 K, plot the thermal efficiency of a completely reversible…

A: For any ReSolution or any doubt Let me know in comment section i will do it again and clear your…

Q: RG 20 mm Ans. n 4 EXERCISES 1. Calculate the power that can be transmitted safely by a pair of spur…

A:

Q: Statics problem

A: Step 1: Step 2: Step 3: Step 4:Here is a detailed, step-by-step solution to your query. If you…

Q: How can i find the volume flow rate in m3/s

A: Given: Diameter of the pipe (d) = 9 cm.            Average velocity of SAE 30W oil in pipe (v) = 3.2…

Q: I. Consider the cantilever beam with a concentrated force. Assume EI of the beam is constant. (a)…

A: For a cantilever beam with a concentrated force at the free end, the reactions at the wall (fixed…

Q: Example The bar Shown Is. subsected to combined loadings as follows: P = = 20.KN F = 0 to 2 KN T=…

A: Step 1:Step 2: Step 3: Step 4:

Q: Question: B10-7 This is a question based on the text book ‘’Mechanics of Materials’’ , please reply…

A:

Q: A toggle clamp is used to apply a friction pad to a flywheel mounted at O, as illustrated below. The…

A:

Q: Question: B08-4 This is a question based on the text book ‘’Mechanics of Materials’’ , please reply…

A: extra

Q: Q7: An amount of a perfect gas has initial conditions of volume (1 m³), pressure (1 bar) and…

A: Step 1: Step 2: Step 3:

Q: 11.2 Boxes A and B are at rest on a conveyer belt that is initially at rest. The belt suddenly…

A: Step 1:  Data Given mA = 100 lb, mB = 80 lb, μA​=0.30 μB​=0.32 Let us first draw the free body…

Q: G = 0.350MPa, P = 900N, a=20mm, b=50mm, c=80mm

A: May this answer helpful to you.

Q: Given the truss below, solve for the internal member forces via the method of joints. Note the loads…

A:

Q: The answer to the problem is 2.93 ft/s. Please show me how to get the final answer

A: Step 1:  vo​=Linear Velocityω=Angular VelocityvP​=Speed of point P Step 2: Step 3:

Q: 12 2 Find the centroid 4 6789

A:

Q: A sphere of radius R=0.1 m is placed in incompressible irrotational flow with V_∞=5 m/s.   Calculate…

A: Step 1:Step 2:

Q: mechanical en

A: I hope this is helpful.

Q: i cannot figure out how to solve

A: note: given Ans is as per direction shown in FBD, put your Ans in your sign convention ( if you take…