The reason for some of the alloy systems having decreased solid solubility to be a good option for age hardening but not commercially needs to be explained. Concept Introduction: The precipitation hardening process comprises of the phenomenon of supersaturation. On maturing for extended times or at elevated temperatures, the solution grows into unbalanced as its diffusivity upsurges manifold. The dispersion happens over the actual brief distances to recompense for the upsurge in the diffusivity. The precipitates have a tendency to produce additional. The heavy force of this phenomenon is the supersaturation triggered due to variations in solubility stages when aged for an extended time or at elevated temperatures. Subsequently, the nucleation of the precipitate stage trailed by its development occurs which is governed by dissimilar diffusion rates at various situations.

Question

Want to see the full answer?

Answer 1

Question

Chapter 12, Problem 12.25P

Interpretation Introduction

Interpretation:

The reason for some of the alloy systems having decreased solid solubility to be a good option for age hardening but not commercially needs to be explained.

Concept Introduction:

The precipitation hardening process comprises of the phenomenon of supersaturation. On maturing for extended times or at elevated temperatures, the solution grows into unbalanced as its diffusivity upsurges manifold.

The dispersion happens over the actual brief distances to recompense for the upsurge in the diffusivity. The precipitates have a tendency to produce additional.

The heavy force of this phenomenon is the supersaturation triggered due to variations in solubility stages when aged for an extended time or at elevated temperatures.

Subsequently, the nucleation of the precipitate stage trailed by its development occurs which is governed by dissimilar diffusion rates at various situations.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

P 20 mm 15 mm 100 mm 200 mm 100 mm 15 mm -450.0 mm- -300.0 mm 300.0 mm -300.0 mm -450.0 mm- 300.0 mm The butt connection shows 8-24mm bolts. Spacing and dimensions are shown in figure PSAD-020. The plate is made of A36 steel. Allowable tensile stress on gross area = 0.6Fy Allowable tensile stress on net area = 0.5Fu Allowable shear stress on net area = 0.3Fu Bolt hole diameter = 26mm Determine the allowable tensile load P based on net area rupture. Determine the allowable tensile load P based on gross area yielding. Determine the allowable tensile load P based on block shear strength. P

300 mm P 75 mm -75 mm P I 75 mm 100 mm -125 mm Shown in figure PSAD-022 is a splice connection made of 8-22mm A325 bolts and a PL 300 x 12 mm made of A36 steel, connected back-to-back. The connection joins together two A992 W410X67 (Fy = 50 ksi, Fu = 65 ksi) carrying a tension load P. Assume U = 0.70. Ignore bolt shear failure. Determine the design capacity of the connection based on yielding of the plate. Determine the design capacity of the section based on yielding of the wide flange section. Determine the design capacity of the section based on rupture of the plate. Determine the design capacity of the section based on block shear of the plate.

Properties of L 152 x 152 x 11.1 A = 3280 mm² d = 152 mm t = 11.1 mm x = 41.9 mm Ix=7.33 x 10 mm⭑ Iy = 7.33 x 10 mm Zx=119 x 103 mm³ Sx = 66.5 x 103 mm³ P ° ° ° ° ° ° ° ° P Shown in figure PSAD-021 is a truss joint detail. It makes use of two rows of 22-mm bolts. The members are L 152 x 152 x 11.1 made of A36. The plate connecting the members is a 9mm-thick A36 plate (Fy = 36 ksi, Fu = 58 ksi). Assume that U = 0.85, ignore 85% limit of net area. Determine the effective net area of the section. Determine the allowable capacity of the connection.