Explanation Introduction: The ROM is the type of memory in which the data can only be read and not be written. The ROM comes under the category of the volatile memory as they store the data even when the system is turned on, thus the data can be retained later. Consider the row inputs are W 1 , W 2 , W 3 and W 4 is the row inputs and the C 1 , C 2 , C 3 and C 4 are the columns input. Also, let the output bits are D 1 , D 2 , D 3 and D . For case (i). To obtain the output 1011 the required row and column inputs are W 1 , C 2 , C 3 and C 4 must be at logic 1. The transistors that must be in the conduction state are the M 00 , M 02 and M 03 . For case (ii). To obtain the output 1111 the required row and column inputs are W 2 , C 1 , C 2 , C 3 and C 4 must be at logic 1

Microelectronics: Circuit Analysis and Design

4th Edition

ISBN: 9780073380643

Author: Donald A. Neamen

Publisher: McGraw-Hill Companies, The

See similar textbooks

Concept explainers

Quantization and Resolution

Quantization is a methodology of carrying out signal modulation by the process of mapping input values from an infinitely long set of continuous values to a smaller set of finite values. Quantization forms the basic algorithm for lossy compression algori…

Probability of Error

This topic is widely taught in many undergraduate and postgraduate degree courses of:

Question

Chapter 16, Problem D16.93P

To determine

To design: The 4×4 bit NMOS mask programmed ROM to produce the given outputs.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 16, Problem 16.92P

Chapter 16, Problem D16.94P

Students have asked these similar questions

An electric resistance space heater is designed such that it resembles a rectangular box 55 cm high, 75 cm long, and 20 cm wide filled with 45 kg of oil. The heater is to be placed against a wall, and thus heat transfer from its back surface is negligible. The surface temperature of the heater is not to exceed 75°C in a room at 25°C for safety considerations. The emissivity of the outer surface of the heater is 0.8 and the average temperature of the ceiling and wall surfaces is the same as the room air temperature. The properties of air at 1 atm and the film temperature are: k = 0.02753 W/m-°C, v=1.798 x 10-5 m²/s, Pr = 0.7228, and ẞ= 0.003096K-1 Wall T₁ =75°C Oil € = 0.8 Electric heater Heating element Disregarding heat transfer from the bottom and top surfaces of the heater in anticipation that the top surface will be used as a shelf, determine the power rating of the heater in W. The power rating of the heater is W.

circuit 2

Suppose you have 8 LED's connected to port-B (Bo-B7) of PIC16F877A and one switch connected to port-D (Do) as shown in figure below. Write a program code that performs a nibble (4-bits) toggling: if the switch is released then LED's (Bo to B3) are OFF and LED's (B4 to B7) are ON, while if the switch is pressed then LED's (Bo to B3) are ON and LED's (B4 to B7) are OFF. Use 300ms delay for each case with 4MHz frequency. 13 14 22 NATHON 20 U1 OSC1/CLKIN U2 33 REOINT 20 34 OSC2/CLKOUT 19 RB1 35 3 18 RB2 RADIANO debt0RB3PGM 30 4 17 37 5 10 RA1/AN1 RB4 38 RA2/ANZ/VREF-/CVREF 15 RB5 39097 RA3/AN3VREF RB6/PGC 7 14 40 RA4/TOCK/C1OUT 13 RB7/PGO RAS/ANA/SS/CZOUT 15 RCO/T1OSO/TICKI 10 11 REQIANS/RD 18 RC1/T10S/CCP2 17 10 RE1/AN/WR REZ/ANTICS MCLR/Vpp/THV RC2/CCP1 LED-BARGRAPH-RED RC3/SCK/SCL RC4/SDUSDA RC5/SDO Eng of ROSTX/CX RC7/RX/DT RDO/PSPO RD1/PSP1 RD2PSP2 RO3/PSP3 RD4/PSP4 ROS/PSP5 RD6/PSP6 RD7/PSP7 PIC16F877A +5V R1 100R

Chapter 16 Solutions

Microelectronics: Circuit Analysis and Design

Ch. 16 - Consider the NMOS inverter with resistor load in...Ch. 16 - The enhancementload NMOS inverter in Figure...Ch. 16 - Prob. 16.3EP Ch. 16 - Prob. 16.4EP Ch. 16 - Consider the NMOS inverter with enhancement load,...Ch. 16 - Prob. 16.2TYU Ch. 16 - (a) Consider the results of Exercise Ex 16.1....Ch. 16 - Prob. 16.5EP Ch. 16 - Prob. 16.6EP Ch. 16 - (a) Design a threeinput NMOS NOR Logic gate with...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

To design: The 4 × 4 bit NMOS mask programmed ROM to produce the given outputs.

Solution Summary: The author explains that the 4times 4 bit NMOS mask programmed ROM produces the given outputs.

Concept explainers

To design: The 4×4 bit NMOS mask programmed ROM to produce the given outputs.

Want to see the full answer?

Chapter 16 Solutions