Concept explainers
The performance data for a centrifugal water pump are shown in Table P14-47E for water at
(a)
The pump efficiency for each data tabulated.
Answer to Problem 47EP
The pump efficiency for each data is represented in Table-(2).
Explanation of Solution
Given information:
Table-(1) represents the volume flow rate, height and power of pump.
Write the expression for pump efficiency.
Here, density of water is
Calculation:
Refer to Table-A-3E "Properties of saturated water" to obtain density of water as
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Table-(2) represents the efficiency of pump for different head, volume flow rate and power.
Table-(2)
(b)
The volume flow rate for BEP of the pump.
The net head for BEP of the pump.
Answer to Problem 47EP
The volume flow rate for BEP of the pump is
The net head for BEP of the pump is
Explanation of Solution
Given information:
Table-(2) represents the efficiency of pump for different head, volume flow rate and power.
Table-(2)
Here, from the Table-(2) the maximum efficiency of pump is
Conclusion:
The volume flow rate for BEP of the pump is
The net head for BEP of the pump is
(b)
The volume flow rate for BEP of the pump.
The net head for BEP of the pump.
Answer to Problem 47EP
The volume flow rate for BEP of the pump is
The net head for BEP of the pump is
Explanation of Solution
Given information:
Table-(2) represents the efficiency of pump for different head, volume flow rate and power.
Table-(2)
Here, from the Table-(2) the maximum efficiency of pump is
Conclusion:
The volume flow rate for BEP of the pump is
The net head for BEP of the pump is
Want to see more full solutions like this?
Chapter 14 Solutions
Fluid Mechanics: Fundamentals and Applications
- Show schematic diagram and complete solutions.arrow_forwardExample (6-1): At the best efficiency point a centrifugal pump, with impeller diameter D=8 in, produces H= 21.9 ft at Q=300 gpm with N=1170 rpm. Compute the corresponding specific speed using a) U.S. customary units. B) SI units (rad/sec, m/sec, m'/sec").c) European units (rev/sec, m/sec, m/sec?). Develop conversion factors to relate the specific speeds.arrow_forwardA pump is working on these parameters 0.56 me/s with TDH of 63 meters. The pump efficiency is at 0.94% and the motor efficiency is at 0,89 %. What is the brake power in kW? Make your answer in whole number and choose the next whole number, say for example 25.2 kW it should be 26 kW.arrow_forward
- image attached. Note: Pump characteristics are in the table circled in yellow. Note: maximum efficiency ( nm)= 0.7arrow_forwardHello i have an example with an answer , please show the solution since only the answer was shown in this example. And i need its solution to review properly. Thank you 1.Question : An existing pump is used to pump water with the following data at BEP: D = 2.15 in, N = 1784 rpm, ρ = 998 kg/m3, Q = 18 gpm, H = 4.2 ft. A larger pump is to be designed based from the existing one to be used for pumping slurry (ρ = 1220 kg/m3) such that its best efficiency point occurs as close as possible to a volume flow rate of 48 gpm and at a net head of 15 ft. Calculate the new pump diameter in inches. Round off your final answer to 3 decimal placesAnswer: 2.554arrow_forwardwhat is the efficiency? what is the NPSHR? what is the motor power requirement?arrow_forward
- This is thermodynamics subject. I need complete solution (step by step process) with given. Thanks Note: Instead of using g = 9.81 m/s^2, use the g = 9.806 m/s^2.arrow_forwardA) Calculate by hand the net head delivered and the efficiency of the pump at flow rate of 63 L/s. B) Use excel sheet and its formula to solve the equations and plot the pump head, power input, and efficiency versus the pump flow ratearrow_forwardThe answer is one of the options below please solve carefully and circle the correct option Please write clear .arrow_forward
- power loss due to wires is calculated by .... e A I2*R B. | C. I*V?arrow_forwardRefer to the “composite performance chart” for a Goulds 3x4-10centrifugal pump operating at 1750 rpm. It shows the pump performance curve for 5 differentimpeller sizes, but also shows the HP required, efficiency, and NPSH required at differentoperating points.Describe the performance of this pump, using an 8 inch impeller and a required flow rate of175 gpm. Give head available, power required (BHP), efficiency, and NPSH req’d. What is the water horsepower (WHP)?arrow_forwardWould the smallest, or the largest, of the seven Taco, Inc.pumps in Fig. be better (a) for producing, near bestefficiency, a water flow rate of 600 gal/min and ahead of95 ft? (b) At what speed, in r/min, should this pump be run?(c) What input power is required?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY