Consider the tube and inlet conditions of Problem 1.36.Heat transfer at a rate of
Want to see the full answer?
Check out a sample textbook solutionChapter 1 Solutions
Fundamentals of Heat and Mass Transfer
Additional Engineering Textbook Solutions
Introduction To Programming Using Visual Basic (11th Edition)
Java How to Program, Early Objects (11th Edition) (Deitel: How to Program)
Modern Database Management
Starting Out with C++ from Control Structures to Objects (9th Edition)
Computer Science: An Overview (13th Edition) (What's New in Computer Science)
Electric Circuits. (11th Edition)
- A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (i) Find the velocity at the nozzle exit. (ii) If the inlet area is 0.1 m2 and specific volume at inlet is 0.19 m3/kg, find the rate of flow of fluid (iii) If the specific volume at the nozzle exit is 0.5 m3/kg, find the exit area of the nozzle.arrow_forwardWater at 940 kPakPa , 25∘C∘C enters a 1-mm-diameter horizontal pipe with a steady velocity of 19 m/sm/s . At the exit the pressure drops to 860 kPakPa due to viscous resistance. Assuming steady-state flow, determine the rate of heat transfer (Q˙Q˙) necessary to maintain a constant specific internal energy (uu).arrow_forwardpls show complete solutionarrow_forward
- Consider the following schematics for a sudden expansion in a pipe.(a) Using the mass and momentum balances to show that there is an overall increaseof pressure equal to the equation in the image.(b) Use energy balance to show that the frictional dissipation is like the equation shown in the image(c) For a constant u1 and A1, show that the pressure rise (P2 - P1) is a maximumwhen the diameter of the larger pipe is √2 times the fixed diameter of the smaller pipe,i.e., A2 = 2A1.arrow_forwardDuring the experiment at time 1:40 min, manometer reading is 5 bar and power consumption at ammeter is 3.3 A. Calculate the work done at that particular time and outlet temperature. Ambient condition: 1 bar and 20 °C Equation for the work done, i.e. output work: n n-1 RT. (S W12 = n- 1 n-1 P. T, = T, Given: Polytropic coefficient: n = 1.3 Ideal gas constant: R = 287 kg K %3D kg Density of air at 20°C: p = 1.2041 Volume flow rate: V = 115 L min Motor Voltage: 230 V at 50 Hz What is the inlet temperature in K and the inlet pressure in bar? What is the outlet temperature at time 1:40 min? At time 1:40 min, how much work is done by the piston? What is the input power at time 1.40 min?arrow_forward(b) Hairdryer is an electromechanical device that blows ambient or hot air over damp hair to speed the evaporation of water to dry the hair. To design a hairdryer, it should contain the following basic components: a duct of constant diameter with a few layers of electric coils, a small fan to pull the air in and force it through the heating coils. If the density of air is 1.18 kg/m³ at the inlet and 0.90 kg/m³ at the exit, calculate the percent increase in the velocity of air as it flows through the dryer.arrow_forward
- Apply the first law of thermodynamics to flow system with two inlets and one outlet. Assume that heat is supplied to the system. Draw the neat sketch and lable inlet and outlet propertiesarrow_forwardPlease refer to image attached tqarrow_forwardFROM BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUDarrow_forward
- Hi please help me answer this question with complete solutionarrow_forward3. In a refinery, certain oil with sp.gr 0.9 flows with a velocity of 2 m/s in a pipe of diameter 30cm. Along the flow, the pipe diameter gets reduced to 25 cm. Determine the velocity and mass flow rate of oil at this section. 4. A circular pipe of uniform diameter 500mm carries water under pressure 30 N/cm2 . The mean velocity of water at the inlet (at the datum) is 2.0 m/s. Find the total head or total energy per unit weight of the water at a cross-section, which is 5 m above the datum line. 5. A tapered pipe, through which water is flowing, is having diameter, 30cm and 20 cm at the cross-sections 1 and 2 respectively. The velocity of water at section 1 is given as 3.5m/s. Find the velocity head at section 1 and 2 and also rate of discharge. 6. Water is flowing through a pipe having diameter 300mm and 200 mm at the bottom and upper end respectively. The pressure at the lower(bigger) end is 25 N/cm2 and the pressure at the upper end is 10 N/cm2. Determine the difference in datum…arrow_forwardWater is to be pumped from the bottom of a well 20 ft deep with a specific heat of 1 BTU/lbm F is pumped using a 1-hp jet pump. Heat is lost from the whole system at the constant rate of 500 BTU/min. What is the temperature (℉) of the water as it enters the vessel if the flow rate of the water is 5 gal/min?assuming that the well water is at 35℉? kindly show all necessary calculationsarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY