Fox And Mcdonald's Introduction To Fluid Mechanics
9th Edition
ISBN: 9781118921876
Author: Pritchard, Philip J.; Leylegian, John C.; Bhaskaran, Rajesh
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 4, Problem 51P
The projectile partially fills the end of the 0.3 m pipe. Calculate the force required to hold the projectile in position when the mean velocity in the pipe is 6 m/s.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A circular balloon is being filled through the inlet, which has a cross-sectional area denoted as A1. The air enters the balloon with a velocity V1 and a density ρ1. If the balloon radius is denoted as R, and the densitywithin is taken as an average value ρavg, construct an expression for the time rate of change of mass withinthe balloon.
1. Water is being discharged through a 5-mm diameter hole on the side and lowermost
portion of a full 200-liter cylindrical tank with a height of 1 meter. Determine the initial
velocity of the water jet as it is ejected from the tank.
2. A hot air balloon is filled with heated air and weighs only about one-half of what air
weighs under identical conditions. The buoyancy force, which can be expressed as
Fp= PairgVbaloon
will push the balloon upward. If the balloon has a diameter of 10 m and
carries a 70 kg person, determine the acceleration of the balloon when it is first released.
Assume the density of air is 1.16 kg/m³, and neglect the weight of the ropes and the cage.
By applying a force F, a saline solution is ejected from the 16-mm diameter syringe through a 0.3-mm diameter needle. If the pressure developed within the syringe is 50 kPa, determine the average velocity (in m/s) of the solution through the needle. Take density of saline = 1,026 kg/m³
Chapter 4 Solutions
Fox And Mcdonald's Introduction To Fluid Mechanics
Ch. 4 - An ice-cube tray containing 250 mL of freshwater...Ch. 4 - A hot air balloon with an initial volume of 2600...Ch. 4 - A fully loaded Boeing 777-200 jet transport...Ch. 4 - On the Milford Trek in New Zealand, there is a...Ch. 4 - A high school experiment consists of a block of...Ch. 4 - For a small particle of styrofoam (density = 19.2...Ch. 4 - Air at 20C and an absolute pressure of 101.3 kpa...Ch. 4 - A block of copper of mass 5 kg is heated to 90C...Ch. 4 - The average rate of heat loss from a person to the...Ch. 4 - The velocity field in the region shown is given by...
Ch. 4 - The area shown shaded is in a flow where the...Ch. 4 - Obtain an expression for the kinetic energy flux,...Ch. 4 - A 0.3 m by 0.5 m rectangular air duct carries a...Ch. 4 - Across a shock wave in a gas flow there is a great...Ch. 4 - Water flows in a pipeline composed of 75-mm and...Ch. 4 - The velocity distribution for laminar flow in a...Ch. 4 - A farmer is spraying a liquid through 10 nozzles,...Ch. 4 - A university laboratory that generates 15 m3/s of...Ch. 4 - Hydrogen is being pumped through a pipe system...Ch. 4 - Calculate the mean velocities for these...Ch. 4 - If the velocity profile in a passage of width 2R...Ch. 4 - Fluid with 1040 kg/m3 density is flowing steadily...Ch. 4 - A rice farmer needs to fill a 150 m 400 m field...Ch. 4 - In your kitchen, the sink is 60 cm by 45.7 cm. by...Ch. 4 - Fluid passes through this set of thin closely...Ch. 4 - A pipeline 0.3 m in diameter divides at a Y into...Ch. 4 - A manifold pipe of 3 in. diameter has four...Ch. 4 - You are trying to pump storm water out of your...Ch. 4 - In the incompressible flow through the device...Ch. 4 - Water enters a wide, flat channel of height 2h...Ch. 4 - Find the average efflux velocity V if the flow...Ch. 4 - Find V for this mushroom cap on a pipeline. P4.32Ch. 4 - Incompressible fluid flows steadily through a...Ch. 4 - A two-dimensional reducing bend has a linear...Ch. 4 - Water enters a two-dimensional, square channel of...Ch. 4 - Viscous liquid from a circular tank. D = 300 mm in...Ch. 4 - A rectangular tank used to supply water for a...Ch. 4 - A cylindrical tank, 0.3 m in diameter, drains...Ch. 4 - Air enters a tank through an area of 0.018 m2 with...Ch. 4 - A cylindrical tank, of diameter D = 50 mm, drains...Ch. 4 - A conical flask contains water to height H = 36.8...Ch. 4 - Water flows steadily past a porous flat plate....Ch. 4 - A tank of fixed volume contains brine with initial...Ch. 4 - A conical funnel of half-angle = 30 drains...Ch. 4 - Evaluate the net rate of flux of momentum out...Ch. 4 - Water flows steadily through a pipe of length L...Ch. 4 - Evaluate the net momentum flux through the bend of...Ch. 4 - Evaluate the net momentum flux through the channel...Ch. 4 - A conical enlargement in a vertical pipeline is 5...Ch. 4 - A 100-mm nozzle is bolted (with 6 bolts) to the...Ch. 4 - The projectile partially fills the end of the 0.3...Ch. 4 - Considering that in the fully developed region of...Ch. 4 - A jet of water issuing from a stationary nozzle at...Ch. 4 - A circular cylinder inserted across a stream of...Ch. 4 - A 6-in.-diameter horizontal pipeline bends through...Ch. 4 - The axes of the pipes are in a vertical plane. The...Ch. 4 - Water flows through a tee in a horizontal pipe...Ch. 4 - In a laboratory experiment, the water flow rate is...Ch. 4 - A gate is 1 m wide and 1.2 m tall and hinged at...Ch. 4 - Water flows steadily through a fire hose and...Ch. 4 - Two types of gasoline are blended by passing them...Ch. 4 - A circular cylinder inserted across a stream of...Ch. 4 - The pressure difference results from head loss...Ch. 4 - Obtain expressions for the rate of change in mass...Ch. 4 - Water is flowing steadily through the 180 elbow...Ch. 4 - Water flows steadily through the nozzle shown,...Ch. 4 - The pump, suction pipe, discharge pipe, and nozzle...Ch. 4 - The passage is 1.2 m wide normal to the paper....Ch. 4 - If the two-dimensional flow rate through this...Ch. 4 - Assume the bend of Problem 4.35 is a segment of a...Ch. 4 - A flat plate orifice of 50 mm diameter is located...Ch. 4 - At rated thrust, a liquid-fueled rocket motor...Ch. 4 - Flow from the end of a two-dimensional open...Ch. 4 - Calculate the magnitude and direction of the...Ch. 4 - This water jet of 50 mm diameter moving at 30 m/s...Ch. 4 - If the splitter is removed from the plate of...Ch. 4 - Consider flow through the sudden expansion shown....Ch. 4 - A conical spray head is shown. The fluid is water...Ch. 4 - A curved nozzle assembly that discharges to the...Ch. 4 - The pump maintains a pressure of 10 psi at the...Ch. 4 - A motorboat moves up a river at a speed of 9 m/s...Ch. 4 - A 30 reducing elbow is shown. The fluid is water....Ch. 4 - A monotube boiler consists of a 6 m length of...Ch. 4 - Water is discharged at a flow rate of 0.3m3/s from...Ch. 4 - A nozzle for a spray system is designed to produce...Ch. 4 - The horizontal velocity in the wake behind an...Ch. 4 - An incompressible fluid flows steadily in the...Ch. 4 - Consider the incompressible flow of fluid in a...Ch. 4 - Air at standard conditions flows along a flat...Ch. 4 - Gases leaving the propulsion nozzle of a rocket...Ch. 4 - Two large tanks containing water have small...Ch. 4 - Students are playing around with a water hose....Ch. 4 - A 2-kg disk is constrained horizontally but is...Ch. 4 - A stream of water from a 50-mm-diameter nozzle...Ch. 4 - A plane nozzle discharges vertically 1200 L/s per...Ch. 4 - In ancient Egypt, circular vessels filled with...Ch. 4 - Incompressible fluid of negligible viscosity is...Ch. 4 - The narrow gap between two closely spaced circular...Ch. 4 - Design a clepsydra (Egyptian water clock), which...Ch. 4 - Water from a stationary nozzle impinges on a...Ch. 4 - A freshwater jet boat takes in water through side...Ch. 4 - The Canadair CL-215T amphibious aircraft is...Ch. 4 - Water, in a 100-mm-diameter jet with speed of 30...Ch. 4 - Consider a series of turning vanes struck by a...Ch. 4 - A steady jet of water is used to propel a small...Ch. 4 - The cart of Problem 4.105 is accelerated by a jet...Ch. 4 - A vane/slider assembly moves under the influence...Ch. 4 - A cart is propelled by a liquid jet issuing...Ch. 4 - For the vane/slider problem of Problem 4.107, find...Ch. 4 - If the cart of Problem 4.105 is released at t = 0,...Ch. 4 - The wheeled cart shown rolls with negligible...Ch. 4 - A rocket sled is to be slowed from an initial...Ch. 4 - Starting from rest, the cart shown is propelled by...Ch. 4 - Solve Problem 4.107 if the vane and slider ride on...Ch. 4 - For the vane/slider problem of Problem 4.114, plot...Ch. 4 - A rectangular block of mass M, with vertical...Ch. 4 - A vertical jet of water impinges on a horizontal...Ch. 4 - A rocket sled traveling on a horizontal track is...Ch. 4 - A rocket sled accelerates from rest on a level...Ch. 4 - A rocket sled with initial mass of 900 kg is to be...Ch. 4 - A rocket sled with initial mass of 3 metric tons,...Ch. 4 - A home-made solid propellant rocket has an initial...Ch. 4 - Neglecting air resistance, what speed would a...Ch. 4 - The moving tank shown is to be slowed by lowering...Ch. 4 - The 90 reducing elbow of Example 4.6 discharges to...Ch. 4 - Crude oil (SG = 0:95) from a tanker dock flows...Ch. 4 - The simplified lawn sprinkler shown rotates in the...Ch. 4 - Calculate the torque about the pipes centerline in...Ch. 4 - A fire truck is equipped with a 66 ft long...Ch. 4 - Calculate the torque exerted on the flange joint...Ch. 4 - Consider the sprinkler of Problem 4.130 again....Ch. 4 - A small lawn sprinkler is shown. The sprinkler...Ch. 4 - When a garden hose is used to fill a bucket, water...Ch. 4 - A pipe branches symmetrically into two legs of...Ch. 4 - Compressed air is stored in a pressure bottle with...Ch. 4 - A turbine is supplied with 0.6 m3/s of water from...Ch. 4 - Air is drawn from the atmosphere into a...Ch. 4 - At high speeds the compressor and turbine of the...Ch. 4 - Transverse thrusters are used to make large ships...Ch. 4 - All major harbors are equipped with fire boats for...Ch. 4 - A pump draws water from a reservoir through a...Ch. 4 - Liquid flowing at high speed in a wide, horizontal...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Give a pseudocode algorithm for determining the length of a file: that is, the number of bytes that are stored ...
Starting Out with C++: Early Objects (9th Edition)
Write code that reads a string from the keyboard and uses it to set the variable myTime of type TimeofDay from ...
Java: An Introduction to Problem Solving and Programming (8th Edition)
ICA 8-34
A sensor is submerged in a silo to detect any bacterial growth in the stored fluid. The stored fluid h...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Determine the slope of the simply supported beam at A. E = 200 GPa and I = 39.9(106) m4. F126
Mechanics of Materials (10th Edition)
(Modified Compound-Interest Program) Modify the application in Fig. 5.6 to use only integers to calculate the c...
Java How to Program, Early Objects (11th Edition) (Deitel: How to Program)
Calculate the cutting time if the length of cut is 24 in., the feed rate is 0.030 ipr, and the cutting speed is...
Degarmo's Materials And Processes In Manufacturing
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- If the static pressure of that fluid in the pipeline is 4.3 ´ 104 Pa while its total pressure is 4.7 ´ 104 Pa, determine the kinetic energy per unit volume of the fluid. Assume that the fluid is incompressible and non-viscous. Consequently, calculate the volume flow rate in the pipeline. Take density of the fluid to be 103 kgm-3and the cross-sectional area of the pipeline as 20 cm2.arrow_forwardA piston 46mm in diameter slides concentrically in a fixed cylinder 50mm in diameter. The cylinder is filled with water and when the piston moves into the annular gap, water flows through the annular gap surrounding the piston. If the velocity of piston is 75mm/s raletive to the cylinder, determine the velocity of flow through the gap.arrow_forwardA water jet traveling at a velocity of 30 meters per second collides with a splitter plate, causing one-fourth of the water to be directed toward the bottom and three-quarters of it to be sent toward the top. 45 degrees is the angle that the plate is at. Determine the amount of force that is needed to keep the plate in place. Ignore the combined weight of the plate and the water, as well as the effects of viscosity.arrow_forward
- Using Bernoulli's principle, determine the pressure change between the upstream and downstream end of the nozzle. The velocities at the entrance and exit are 2.55m/s and 1.13m/s,respectively. Note: Temperature is 20 degrees centigrade. Nozzle is horizontal.arrow_forwardA liquid of density p is filled in a vessel of cross- sectional area A. The vessel has a hole of cross-sec- tional area a at a depth h below the free surface of the liquid. When the hole is unplugged, the liquid comes out of the hole with a velocity v. The volume of liquid coming out of the hole per second is Q. The reaction force exerted on the vessel by the emerging liquid is (assume A >> a) (a) av²p (b) 2aghp (c) ро@ (d) рQ /2gharrow_forwardDetermine the magnitude and direction of the resultant force exerted on the double nozzle depicted in the figure, given that the pipes' axes and both nozzles lie in the horizontal plane, with both nozzle jets having a water velocity of 20 m/s. 150 mm 5 degree 250 mm 25 degree 100 mmarrow_forward
- A jet of water has a velocity of 20m/s and flows at 2kgs/s. The jet strikes a stationary flat plate. The normal direction to the plate is inclined at 30º to the jet.Determine the force on the plate in the direction of the jet.arrow_forwardOil flows through the 200-mm-diameter pipe with a velocity of 8 m/s as shown in . Take P, = 870 kg/m 200 mm 100 mm 8 mis Part A If it discharges into the atmosphere through the nozzle, determine the total force the bolts must resist at the connection AB to hold the nozzle onto the pipe. Express your answer to three significant figures and include the appropriate units.arrow_forwardWater flows into the horizontal bend fitting at A with a velocity of V = 4.2 m/s, and exits at B into the atmosphere as shown in . A 150 mm 200 mm 400 mm 30 Part A Determine the r-component of force at C needed to hold the fitting in place. Express your answer to three significant figures and include the appropriate units.arrow_forward
- An enclosed tank containing a liquid of density r has a hole in its side at a distance y1 from the tank’s bottom (as shown). The hole is open to the atmosphere, and its diameter is much smaller than the diameter of the tank. The air above the liquid is maintained at a pressure P. Determine the speed of the liquid as it leaves the hole when the liquid’s level is a distance h above the hole.arrow_forwardA jet issues without loss from a hole in a water tank that is open to the atmosphere. The hole is located a distance H below the free surface, and the jet issues at an angle θ to the horizontal direction, and it has an exit area of A. Express the maximum height of the jet as a function of θ and H (which is held constant). What is the the horizontal component of the force exerted on the tank by the jet? Ignore losses.arrow_forwardThe gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of 18 m/s, and out the pipe at B and C with the same velocity v. Neglect the weight of water within the pipe and the weight of the pipe. The pipe has a diameter of 50 mm at A, and at B and C the diameter is 35 mm. Pw = 1000 kg/m³. (Figure 1) Determine the x component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Express your answer to three significant figures and include the appropriate units. • View Available Hint(s) ? Fr = Value Unitsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY
Dynamics of Fluid Flow - Introduction; Author: Tutorials Point (India) Ltd.;https://www.youtube.com/watch?v=djx9jlkYAt4;License: Standard Youtube License