Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 23, Problem 43QTP
A high-strength cast-iron bar 8 in. in diameter is being turned on a lathe at a depth of cut d = 0.050 in. The lathe is equipped with a 15-hp electric motor and has a
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine.
Using the given data find the following.
(i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm
(ii) During machining the tool's approach length is 5 mm, over run length is 2mm
(iii) Total time required to complete the turning operation is 59.6 minutes
A mild steel specimen of Initial diameter of
53.5 mm is turned to final diameter of 47 mm
for an initial length of 154 mm on a lathe
machine.
Using the given data find the following.
(i) Feed of 0.4 mm/rev & Depth of cut is 0.5
mm
(ii) During machining the tool's approach
length is 5 mm, over run length is 2mm
(iii) Total time required to complete the
turning operation is 59.6 minutes
(a) Find number of passes to finish the entire
turning operation (
(b) The actual length of the turning operation
in mm ('
In a turning operation on low carbon steel with hardness = 135 HB, the cutting speed = 180 m/min, feed = 0.35 mm/rev, and depth of cut = 6.5 mm. The
original work piece has 26 mm Diameter and 120 mm Length. How much power will the lathe draw in performing this operation if its mechanical efficiency =
90% and operator's efficiency = 82%? The specific energy is 3.8 J/mm³
Chapter 23 Solutions
Manufacturing Engineering & Technology
Ch. 23 - Describe the types of machining operations that...Ch. 23 - What is turning? What kind of chips are produced...Ch. 23 - What is the thrust force in turning? What is the...Ch. 23 - What are the components of a lathe?Ch. 23 - (a) What is a tracer lathe? (b) What is an...Ch. 23 - Describe the operations that can be performed on a...Ch. 23 - Why were power chucks developed?Ch. 23 - Explain why operations such as boring on a lathe...Ch. 23 - Why are turret lathes typically equipped with more...Ch. 23 - Describe the differences between boring a...
Ch. 23 - How is drill life determined?Ch. 23 - What is the difference between a conventional...Ch. 23 - Why are reaming operations performed?Ch. 23 - Explain the functions of the saddle on a lathe.Ch. 23 - Describe the relative advantages of (a)...Ch. 23 - Explain how external threads are cut on a lathe.Ch. 23 - Prob. 17RQCh. 23 - Explain the reasoning behind the various design...Ch. 23 - Note that both the terms tool strength and...Ch. 23 - (a) List and explain the factors that contribute...Ch. 23 - Explain why the sequence of drilling, boring, and...Ch. 23 - Why would machining operations be necessary even...Ch. 23 - A highly oxidized and uneven round bar is being...Ch. 23 - Describe the difficulties that may be encountered...Ch. 23 - (a) Does the force or torque in drilling change as...Ch. 23 - Explain the similarities and differences in the...Ch. 23 - Describe the advantages and applications of having...Ch. 23 - Assume that you are asked to perform a boring...Ch. 23 - Explain the reasons for the major trend that has...Ch. 23 - Describe your observations concerning the contents...Ch. 23 - The footnote to Table 23.12 states that as the...Ch. 23 - In modern manufacturing, which types of metal...Ch. 23 - Sketch the tooling marks you would expect if a...Ch. 23 - What concerns would you have in turning a powder...Ch. 23 - The operational severity for reaming is much lower...Ch. 23 - Review Fig. 23.6, and comment on the factors...Ch. 23 - Explain how gun drills remain centered during...Ch. 23 - Comment on the magnitude of the wedge angle on the...Ch. 23 - If inserts are used in a drill bit (see Fig....Ch. 23 - Refer to Fig. 23.11b, and in addition to the tools...Ch. 23 - Calculate the same quantities as in Example 23.1...Ch. 23 - Estimate the machining time required to rough turn...Ch. 23 - A high-strength cast-iron bar 8 in. in diameter is...Ch. 23 - A 0.30-in.-diameter drill is used on a drill press...Ch. 23 - In Example 23.4, assume that the workpiece...Ch. 23 - For the data in Problem 23.45, calculate the power...Ch. 23 - A 6-in.-diameter aluminum cylinder 10 in. in...Ch. 23 - A lathe is set up to machine a taper on a bar...Ch. 23 - Assuming that the coefficient of friction is 0.25,...Ch. 23 - A 3-in.-diameter, gray cast iron cylindrical part...Ch. 23 - Would you consider the machining processes...Ch. 23 - Would it be difficult to use the machining...Ch. 23 - If a bolt breaks in a hole, it typically is...Ch. 23 - An important trend in machining operations is the...Ch. 23 - Review Fig. 23.8d, and explain if it would be...Ch. 23 - Boring bars can be designed with internal damping...Ch. 23 - A large bolt is to be produced from extruded...Ch. 23 - Make a comprehensive table of the process...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 49 mm for an initial length of 151 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.2 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 7 mm, over run length is 4mm (iii) Total time required to complete the turning operation is 52.6 minutes (a) Find number of passes to finish the entire turning operation (b) The actual length of the turning operation in mm (c)The time required to complete one single turning operation in minutes (d) Spindle speed in rpmarrow_forwardThe end of a large tubular workpart is to be faced on a NC vertical boring mill. The part has an outside diameter of 38.0 in and an inside diameter of 24.0 in. If the facing operation is performed at a rotational speed of 40.0 rev/min, feed of 0.015 in/rev, and depth of cut of 0.180 in, determine (a) the cutting time to complete the facing operation and the cutting speeds and metal removal rates at the beginning and end of the cut.arrow_forwardA mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutesarrow_forward
- A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=arrow_forwardA mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.3 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 6 mm, over run length is 3mm (iii) Time required to complete one single turning operation is 2.3 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes (c) Spindle speed in in rpm (d) Cutting speed in m/minutesarrow_forward1. A 7.5 -mm-diameter drill is used on a drill press operating at 300 rpm. If the feed is 0.125 mm/rev, what is the MRR? What is the MRR if the drill diameter is doubled? 2. Assume that the work piece material is high-strength aluminum alloy and the spindle is running at N = 500 rpm. Estimate the torque required for this operation.arrow_forward
- 1.10A O50 mild steel bar is being tumed at 1.70 revis on a multi-tool center lathe having nine tools. For all tools the depth of cut is 4mm, the feed is 0.255mm/rev, and the specific cutting pressure is 1 545N/mm. Calculate the total power consumed for the operationarrow_forwardb) A mild steel having length of 350mm and diameter of 12.5 cm, is being reduced to diameter 9.5 cm, for the length of 22cm by turning on lathe, with a spindle speed of 250rpm. Assume feed (f) 2.5 mm/rev and 2 passes to complete the turning operation. Write the formula and calculate (i) Cutting speed (ii) Depth of cut.arrow_forwardA cylindrical work bar with 4.5 in diameter and 52 in length is chucked in an engine lathe and supported at the opposite end using a live center. A 46.0 in portion of the length is to be turned to a diameter of 4.25 in one pass at a speed of 450 ft/min. The metal removal rate should be 6.75 in3 /min. Determine (a) the required depth of cut, (b) the required feed, and (c) the cutting time.arrow_forward
- Your manager has asked you to submit a report based on lead screws and screw jacks on plant premises. You need to include following calculations for the report. 1. The lead screw of a lathe has Acme threads of 50 mm outside diameter and 8 mm pitch. The screw must exert an axial pressure of 2500 N in order to drive the tool carriage. The thrust is carried on a collar 110 mm outside diameter and 55 mm inside diameter and the lead screw rotates at 30 r.p.m. Determine (a) the power required to drive the screw; and (b) the efficiency of the lead screw. Assume a coefficient of friction of 0.15 for the screw and 0.12 for the collar. 2. The lead screw of a lathe has Acme threads of 60 mm outside diameter and 8 mm pitch. It supplies drive to a tool carriage which needs an axial force of 2150 N. A collar bearing with inner and outer radius as 30 mm and 60 mm respectively is provided. The coefficient of friction for the screw threads is 0.12 and for the collar it is 0.10. Find the torque…arrow_forwardWe need to obtain the following part by OD operation in turning, starting from a 100mm diameter cylinder. The maximum allowable depth of cut is 3mm. It is required to make a finishing pass with d=1mm and a feed of 0.3mm/revolution. 150 mm 150 mm The machine has a total power of 10hp and 85% efficiency. The material has a specific energy 500 based on of 25 W/(cm³/min). It is recommended to make the operation at a constant rpm = calculations made for an average diameter. Determine the minimum required time to finish the part. Hint: calculate the maximum material removal rate then the cutting speed for each pass, then the feed rate for each pass and finally the time of cutting. 80 mm 100 mmarrow_forwardA motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm2. If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate: 4.1. Energy required to cut a hole. 4.2. Energy required for cutting work per second. 43. Maximum fluctuation of energy of the flywheel. 4.4. Mass of the flywheel having radius of gyration of 1.5 m.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License