The compartment heater of an automobile exchangesheat between warm radiator fluid and cooler outsideair. The flow rule of water is large compared to the air, and the effectiveness,
(a) It the fan is switched to high and
(b) For the low-speed fan condition, the heater warmsoutdoor air from 0 to 30°C. When the fan is turnedto medium, the airflow rate increases 50% and theheat transfer increases 20%. Find the new outlettemperature.
Want to see the full answer?
Check out a sample textbook solutionChapter 11 Solutions
Fundamentals of Heat and Mass Transfer
Additional Engineering Textbook Solutions
Engineering Mechanics: Statics & Dynamics (14th Edition)
EBK FUNDAMENTALS OF THERMODYNAMICS, ENH
HEAT+MASS TRANSFER:FUND.+APPL.
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Heating Ventilating and Air Conditioning: Analysis and Design
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
- Air is used as a working substance in a given internal combustion engine, which is supplied with heat at a constant volume. Based on the data, calculate the Pressure rise ratearrow_forwardAn ammonia refrigeration plant operates between a condensing temperature of 40°C and an evaporating temperature of –10°C. The vapour is dry at the end of compression. Only the following property values are given: 8. °C kJ/kg kJ/kg kJ/kg.K 40°C 371.5 1473 1.36 |-10°C 135.4 1433 0.544 The specific heat of NH3 vapour is 2.1897 kJ/kg.K. Calculate the theoretical coefficient of performance of the cycle.arrow_forwardAn electronic chip is working, and its outer surface is cooled convectively by a fan. The heat-transfer coefficient, h, is 100W/(m^2∙K), and the total surface area of the chip, A, is 5 cm^2. We also know the temperature of the cooling air, Tb, is 25 C, and the temperature of the chip, Ts, is 75 C. The whole system of the chip is in steady state. Please determine 1) the energy transfer rate, ???? , in W; 2) the heat transfer rate, ?̇ in W; and 3) the power of the chip, ?̇ , in W.arrow_forward
- 20 kg/s of steam enters a condenser at a pressure of 0.08 bar and quality of 0.68 and exits as saturated liquid at the same pressure. What is the mas flow rate of cooling water if the temperature rise of cooling water is 10 oC and its specific heat equals 4.2 kJ/kg.k?arrow_forwardA refrigeration unit with COP = 3.8 is being used to remove heat from a particular machine by 0.42 kg/s of water (C, = 4.18 kJ/kg.K) at 20 °C that is chilled from 40 °C as shown in the Figure. What is the power input (in kW) to the refrigeration unit? Select one: O 11.15 1 2 10.97 9.24 REF TH O 13.26 QH O 14.63 O 12.32arrow_forwardPlease answer asap.. I will rate helpful thankyouarrow_forward
- Please show the complete solution.arrow_forwardIt generates power in a process consisting of air compressor-heat exchanger and turbine units. Air is considered the ideal gas. The compressor and turbine are adiabatic and the kinetic and potential energy changes in the units are negligible. The specific heat of the air is 1,005 kJ / kgK, k = 1,4. Accordingly, how many kW is the compressor power?, ps: ısı ejanşörü = heat exchanger kompresör= compressor türbin = turbinearrow_forward1) Given 753.06 kW electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(10^5) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Answer the following: a) Calculate the exergy destroyed in the process below. The exergy of the fuel entering this process is 51.82 MJ/Kg. The dead state temperature is 293.2 K and pressure is 1 bar. The products of combustion leave this process at the dead state. Process: 0.015 kg is the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of the problem above. if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg. b) The utility providing the…arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning