Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470501979
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 11, Problem 11.22P
A shell-and-tube heat exchanger must be designed to heat 2.5 kg/s of water from 15 to 85°C. The heating isto be accomplished by passing hot engine oil, whichis available at 160°C, through the shell side of theexchanger. The oil is known to provide an averageconvection coefficient of
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Please fast solve the issue
Water (cp = 4182 J/Kg.K) at a flow rate of 5000 Kg/hr is heated from 10oC to 35oC in an oil cooler by engine oil (cp = 2072 J/Kg.K) with an inlet temperatureof 85oC and a flow rate of 6000 Kg/hr. Take the overall heat transfer coefficient to be 3500 W/m2.K. What are the areas required for:a. Parallel Flow.b. Counter Flow
A double pass water-cooled shell-and-tube type condenser has a total number of tubes equal to 42. The tubes are of 14 mm inside diameter, 16 mm outside diameter and 4 m length. The overall heat transfer coefficient is 3510 kJ/hr-m2 -°C. Cooling water enters the condenser at 25°C at a velocity of 1.5 m/s and leaves with a temperature rise of 6.5°C. (a) Calculate the outside heating surface area of the tubes in m2 ; (b) Determine the mass flow rate of water in kg/s and the volumetric flow rate in L/s (using an average density of 996.5 kg/m3 ); (c) Estimate the condensing temperature of the refrigerant; (d) If the ammonia refrigerant enters and leaves the condenser at saturation conditions, compute the mass flow rate of the refrigerant and the condenser pressure in kPa.
Chapter 11 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 11 - In a fire-tube boiler, hot products of combustion...Ch. 11 - A shell-and-tube heat exchanger is to heat an...Ch. 11 - A steel tube (k=50W/mK) of inner and outer...Ch. 11 - A heat recovery device involves transferring...Ch. 11 - A novel design for a condenser consists of a tube...Ch. 11 - The condenser of a steam power plant...Ch. 11 - Thin-walled aluminum tubes of diameter D = 10mmare...Ch. 11 - A tinned-tube, cross-how heat exchanger is to use...Ch. 11 - Water at a rate of 45,500kg/h is heated from 80...Ch. 11 - A novel heat exchanger concept consists of a...
Ch. 11 - Prob. 11.12PCh. 11 - A process fluid having a specific heat of...Ch. 11 - A shell-and-tube exchanger (two shells, four tube...Ch. 11 - Consider the heat exchanger of Problem 11.14....Ch. 11 - The hot and cold inlet temperatures to a...Ch. 11 - A concentric tube heat exchanger of length L = 2 m...Ch. 11 - A counterflow, concentric tube heat exchanger is...Ch. 11 - Consider a concentric tube heat exchanger with an...Ch. 11 - A shell-and-tube heat exchanger must be designed...Ch. 11 - A concentric tube heat exchanger for cooling...Ch. 11 - A counterflow, concentric tube heat exchanger used...Ch. 11 - An automobile radiator may be viewed as a...Ch. 11 - Hot air for a large-scale drying operation is to...Ch. 11 - In a dairy operation, milk at a flow rate of 250...Ch. 11 - The compartment heater of an automobile...Ch. 11 - A counterflow, twin-tube heat exchanger is made...Ch. 11 - Consider a coupled shell-in-tube heat exchange...Ch. 11 - For health reasons, public spaces require the...Ch. 11 - A shell-and-tube heat exchanger (1 shell pass, 2...Ch. 11 - Saturated water vapor leaves a steam turbine at a...Ch. 11 - The human brain is especially sensitive to...Ch. 11 - Prob. 11.47PCh. 11 - A plate-tin heat exchanger is used to condense a...Ch. 11 - In a supercomputer, signal propagation delays...Ch. 11 - Untapped geothermal sites in the United States...Ch. 11 - A shell-and-tube heat exchanger consists of 135...Ch. 11 - An ocean thermal energy conversion system is...Ch. 11 - Prob. 11.55PCh. 11 - Prob. 11.56PCh. 11 - The chief engineer at a university that is...Ch. 11 - A shell-and-tube heat exchanger with one shell...Ch. 11 - Prob. 11.59PCh. 11 - Prob. 11.60PCh. 11 - Prob. 11.61PCh. 11 - Prob. 11.62PCh. 11 - A recuperator is a heat exchanger that heats air...Ch. 11 - Prob. 11.64PCh. 11 - Prob. 11.65PCh. 11 - A cross-flow heat exchanger consists of a bundle...Ch. 11 - Exhaust gas from a furnace is used to preheat the...Ch. 11 - Prob. 11.68PCh. 11 - A liquefied natural gas (LNG) regasification...Ch. 11 - Prob. 11.70PCh. 11 - A shell-and-tube heat exchanger consisting of...Ch. 11 - Prob. 11.73PCh. 11 - The power needed to overcome wind and friction...Ch. 11 - Prob. 11.75PCh. 11 - Consider a Rankine cycle with saturated steam...Ch. 11 - Consider the Rankine cycle of Problem 11.77,...Ch. 11 - Prob. 11.79PCh. 11 - Prob. 11.80PCh. 11 - Hot exhaust gases are used in a...Ch. 11 - Prob. 11.84PCh. 11 - Prob. 11.90PCh. 11 - Prob. 11S.1PCh. 11 - Prob. 11S.2PCh. 11 - Prob. 11S.3PCh. 11 - Solve Problem 11.15 using the LMTD method.Ch. 11 - Prob. 11S.5PCh. 11 - Prob. 11S.6PCh. 11 - Prob. 11S.8PCh. 11 - Prob. 11S.10PCh. 11 - Prob. 11S.11PCh. 11 - A cooling coil consists of a bank of aluminum...Ch. 11 - Prob. 11S.17P
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Assume the following vectors are already defined: V1=[302]V2=[214]V3=[5131]V4=[0.50.10.20.2] For each of the fo...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Describe the structural changes that take place when a plain-carbon eutectoid steel is slowly cooled from the a...
Foundations of Materials Science and Engineering
Determine the length of the cantilevered beam so that the maximum bending stress in the beam is equivalent to t...
Mechanics of Materials (10th Edition)
The spring of k and unstretched length 1.5R is attached to the disk at a radial distance of 0.75R from the cent...
Engineering Mechanics: Statics
Find the change in length of side AB.
Mechanics of Materials, 7th Edition
6–1C A mechanic claims to have developed a car engine that runs on water instead of gasoline. What is your resp...
Thermodynamics: An Engineering Approach
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In a hydrocarbon processing plant, Fluid A (cp = 4.31 kJ/kg-K) entering the tube side is used to heat Fluid B (cp = 2.05 kJ/kg-K) in a heat exchanger with an overall heat transfer coefficient of 150 W/m2.°C. Based on the information given in TABLE Q3, determine the outlet temperatures of Fluid A and Fluid B. If the surface area of the heat exchanger increases 30%, what would be the effect on outlet temperatures? Justify your answer with calculation. Comment your answer. TABLE Q3 Type of heat exchanger Mass flow Inlet Surface rate, kg/s temperature, °C area, A, m2 Fluid Fluid Fluid Fluid A в А B 3.0 5.5 150 20 150 Cross flow, both fluid unmixed 3.arrow_forwardYou are designing a piping system to facilitate the transfer of water from one industrialprocess to the next. You need the water to condense from saturated vapor to saturatedliquid at a constant 1000 kPa as it flows through the piping system. The pipe is to be madeof plain carbon steel with thermal conductivity ? = 60 W m-K⁄ and inner and outer radii?? = 5 cm and ?? = 7 cm, respectively. The thermodynamic property table at the end of thisproblem will be helpful throughout your analysis.a) If the convection coefficient between the steam and inner wall of the pipe is “verylarge”, what is the temperature of the inner pipe wall along its entire length?(Hint: Isobaric phase change is also iso___?)b) The fluid surrounding the pipe has temperature ?∞ = 30°C and the convectioncoefficient from the pipe to this fluid is ℎ = 100 W/m2⋅K. What is the heat transferrate out of the pipe, per unit meter of pipe? You may neglect radiation effects. Usea thermal resistance network in your analysis.c) The…arrow_forwardA long thin-walled double-pipe heat exchanger with tube and shell diameters of 2 cm and 4 cm, respectively, is used to condense refrigerant-134a by water at 20 C. The refrigerant flows through the tube, with a convection heat transfer coefficient of hi = 4000 W/m2 K.A 1-mm-thick layer of limestone (k = 1.2 W/mK) forms on the outer surface of the inner tube. Water flows through the shell at a rate of 0.4 kg/s. Determine the overall heat transfer coefficient U of this heat exchanger with and without the fouling factor, and the error in U introduced by neglecting the fouling factor. Comment the fouling effect on this heat exchanger.arrow_forward
- A double-pipe counter-flow heat exchanger isto cool eth ylene glycol (Cp = 2560 J/kg-°C) flowing at a rate of 3.5 kg/s from 80°C to 40°C by water (Cp = 4180 J/kg-°C) that enters at 20°C and leaves at 55°C. The overall heat transfer coefficient based on the inner surface area ofthetubeis 250 W/m2°C. Determine theheat transfer surface area on the inner side ofthetube. m2arrow_forwardA long, thin-walled double-pipe heat exchanger with tube and shell diameters of 0.01 m and 0.025 m, respectively, is used to condense refrigerant-134a with water at 20°C. The refrigerant flows through the tube, with a convection heat transfer coefficient of hi= 4100 W/m² °C. Water flows through the shell at a rate of 0.3 kg/s. The thermal resistance of the inner tube is negligible since the tube material is highly conductive and its thickness is negligible. Both the water and refrigerant-134a flows are fully developed. Properties of the water and refrigerant-134a are constant. Water properties: p = 998 kg/m³, v=u/p-1.004x 10-6 m²/s, k = 0.598 W/m. °C, Pr = 7.01 Cold water D Doarrow_forwardThe condenser of a room air conditioner is designedto reject heat at a rate of 15,000 kJ/h from refrigerant-134aas the refrigerant is condensed at a temperature of 408C. Air(cp 5 1005 J/kg?K) flows across the finned condenser coils,entering at 258C and leaving at 358C. If the overall heat transfer coefficient based on the refrigerant side is 150 W/m2?K,determine the heat transfer area on the refrigerant side.arrow_forward
- Milk is flowing through a heat exchanger at a rate of 2000 kg/h. The heat exchanger supplies 111,600 kJ/h. The outlet temperature of the product is 95℃. Determine the inlet temperature of the milk. The product specific heat is 3.9kJ/(kg℃). Show PBD and complete solution.arrow_forwardRead the question carefully and give me right solution with clear calculations. Thank youarrow_forwardI need the answer as soon as possiblearrow_forward
- The water (C, = 4180 J/kg - °C) enters the 2.5-cm internal-diameter tube of a double-pipe counter-flow heat exchanger at 17°C at a rate of 3 kg/s. It is heated by steam condensing at 120°C (he = 2203 kJ/kg) in the shell. If the overall heat transfer coefficient of the heat exchanger is 1500 W/m? - °C, determine the length of the tube required in order to heat the water to 80°C. Steam 120°C Water 80°C 17°C 3 kg/sarrow_forwardEthanol is vaporized at 788C (hfg 5 846 kJ/kg) in adouble-pipe parallel-flow heat exchanger at a rate of 0.03 kg/sby hot oil (cp 5 2200 J/kg?K) that enters at 1208C. If the heattransfer surface area and the overall heat transfer coefficientsare 6.2 m2and 320 W/m2?K, respectively, determine the outlettemperature and the mass flow rate of oil using (a) the LMTDmethod and (b) the e2NTU method.arrow_forwardAn air-cooled condenser has an h value of 30 W/m2-K based on the air-side area. The air-side heat transfer area is 190 m2 with air entering at 27°C and leaving at 40°C. If the condensing temperature is constant at 49°C, what is the air mass flow rate in kg/s? Let Cp(air) = 1.006 kJ/kg-K. Draw and label the temperature-flow diagram. Round off your answer to three (3) decimal places.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
How Shell and Tube Heat Exchangers Work (Engineering); Author: saVRee;https://www.youtube.com/watch?v=OyQ3SaU4KKU;License: Standard Youtube License