An ammonia refrigeration plant operates between a condensing temperature of 40°C and an evaporating temperature of –10°C. The vapour is dry at the end of compression. Only the following property values are given: 8. °C kJ/kg kJ/kg kJ/kg.K 40°C 371.5 1473 1.36 |-10°C 135.4 1433 0.544 The specific heat of NH3 vapour is 2.1897 kJ/kg.K. Calculate the theoretical coefficient of performance of the cycle.

An ammonia refrigeration plant operates between a condensing temperature of 40°C and an evaporating temperature of –10°C. The vapour is dry at the end of compression. Only the following property values are given: 8. °C kJ/kg kJ/kg kJ/kg.K 40°C 371.5 1473 1.36 |-10°C 135.4 1433 0.544 The specific heat of NH3 vapour is 2.1897 kJ/kg.K. Calculate the theoretical coefficient of performance of the cycle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Using the table
Consider a condensing heat exchanger operating with two separate fluids, R-134a and the water. Assuming the operating conditions listed in the table below, and that the pressure drop of the fluids are negligible, find the mass flowrate of the water (kg/s) and Q (kW) transferred between the R-134a and the water. m Enters Exits Fluid Water ? Liquid at T₁ = 5 °℃ Liquid at T₂ = 25 °℃ T2 = 35 °C R-134a 10 kg/min P₁ = 1 MPa and T₁ = 70 °C
Superheated steam is contained in a 4.25-m rigid- tank at a constant temperature T = 350 °C. The initial pressure inside the tank is 3500 kPa. A valve is opened, and 0.75 kg/min of steam allowed to escape from the tank. How long it takes (in minutes) for pressure inside the tank to reach to 600 kPa? Select one: 61.84 69.74 82.05 Not listed 56.76 50.63 72.75
Problem 2. Consider a Variable Air Volume (VAV) system, which serves for two rooms. The air temperature at the exist of the cooling coil is 10 °C. The design room temperature is 24 °C for both rooms. For room 1, the sensible and latent heat load is 60 and 10 kW, respectively. For room 2, the sensible and latent heat load is 40 and 10 kW, respectively. Determine (1) The mass flow rate for each room in kg/s; (2) The actual relative humidity of each room.
Refrigerant vapor rejects 70 kW of heat as it passes through an air-cooled condenser. The condenser has an air-side area of 210 m2 and, based on this area, has an overall heat transfer coefficient of 0.037 kW/m2∙°C. Cooling air flows at a rate of 7.59 kg/s. If condensation of the refrigerant occurs at 55°C, what is the inlet temperature (in °C) of the air? Take the specific heat of air to be 1.02 kJ/kg∙°C. Round your answer to 2 decimal places.
! Required information Problem 08.048 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS - Piston Device with Refrigerant NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A piston-cylinder device initially contains 2 kg of refrigerant-134a at 100 kPa and 20°C. Heat is now transferred to the refrigerant from a source at 150°C, and the piston, which is resting on a set of stops, starts moving when the pressure inside reaches 120 kPa. Heat transfer continues until the temperature reaches 80°C. Assume the surroundings to be at 25°C and 100 kPa. R-134a 100 kPa 20°C Q 150°C Problem 08.048.c - Exergy Destroyed by Piston Device with Refrigerant Determine the exergy destroyed. (You must provide an answer before moving on to the next part.) The exergy destroyed is kJ.
In a closed feedwater heater, steam warms the feedwater and the condensate leaves the heater through a trap or throttling value . What is the purpose of the trap or throttling value? It allows the liquid to flow to higher pressures with the same internal energy. It separates the liquid from the vapor. It allows the liquid to flow into a lower pressures without the loss of enthalpy. It allows the liquid to flow to higher pressures with the same enthalpy. It allows the liquid to flow into a lower pressures without the loss of internal energy.
6. A Carnot power cycle employing 1 lbm of air as a working substance is presumed to operate between temperatures limits of 600 °F and 70 °F. The pressure at the beginning and end of the isothermal expansion process area 510 psia and 170 psia, respectively. Determine the change of volume in ft³ between the end of isentropic expansion and the end of isentropic compression.
The air in a theatre room must be 22 °C and the relative humidity 55%. The outdoor temperature is 30 °C and relative humidity 50%. There are 900 seats in the room and 25 m³/h of fresh air is reserved for each seat. Every attendant releases a heat load (sensible + latent) of 100 W and a moisture load of 80 g/h. The sum of heat loads from other than human sources is 20 kW. What must the supply air state be in order to maintain the indoor conditions mentioned above?
An air-standard set of processes with constant specific heats is executed in a closed system and is composed of the following:1-2 Isentropic compression from 100 kPa and 25°C to 600 kPa2-3 Isometric heat addition to 1500 K3-4 Isentropic expansion to 100 kPa4-1 Isobaric heat rejection to initial state Question: Following the given data, perform the following:a. Plot the P-V and T-S Diagram of the cycleb. Calculate the net work output of the cycle (kJ/kg)c. Calculate the Thermal Efficiency (%)
A steam power plant is located in the northern part of the country. Steam in the plant flows steadily through a 0.17-m diameter pipeline from the steam generating unit (SGU) to the steam turbine. At the SGU end, the steam conditions are determined to be P = 4 MPa, t = 400°C, h = 3,247 kJ/kg, and specific volume = 0.181 m³/kg. At the steam turbine end, the conditions are found to be P = 3.5 MPa, t = 392°C, h = 3,178.3 kJ kg, and specific volume = 0.248 m³/kg. Heat loss from the pipeline is 7.86 kJ/kg. Determine the steam mass flow rate in kg/s.
I need the answer as soon as possible