Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 10, Problem 34P
A blower has a rotor with 12-in. outside diameter and 10-in. inside diameter with 1,5-in high rotor blades. The flow rate through the blower is 500 ft3/min at a rotor speed of 1800 rpm. The air at blade inlet is in the radial direction and the discharge angle is 30° from the tangential direction. Determine the power required by the blower motor.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Fans-2
5. The power output is 35 Hp to a centrifugal pump that is discharging 905
gpm and which operates at 1805 rpm against a head H= 125 ft, 220 V, 3
phase, 60 Hertz. If this pump is modified to operate 1205 rpm, assuming
its efficiency remains constant, determine its power input to the pump.
2.
A Pelton wheel is working under a head of
180 m with a discharge of 0.8 m3 /s. The
following data are available for the turbine:
Coefficient of velocity = 0.985 Angle of deflection of jet = 165°
Speed ratio 0.46
Relative velocity at exit = Relative velocity at
inlet
Jet ratio 12
Compute the (a) hydraulic efficiency, (b)
velocity of whirl at inlet and outlet, and (c)
mean bucket speed. Assume zero frictional loss
in the bucket.
An inward flow reaction turbine, having an inner and outer diameter of 0.45m and 0.90m, respectively. The vanes are radial at inlet and the discharge is radial at outlet and the water enters the vanes at an angle of 12°. Assuming the velocity of flow as constant and equal to 2.8m/s, find the speed of the wheel and the vane angle at outlet.
Show schematic diagram and provide solutions.
Chapter 10 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 10 - The geometry of a centrifugal water pump is r1 =...Ch. 10 - Find the resulting -groups when (a) D, , and Q or...Ch. 10 - Consider the centrifugal pump impeller dimensions...Ch. 10 - Dimensions of a centrifugal pump impeller areCh. 10 - Dimensions of a centrifugal pump impeller areCh. 10 - The blade is one of a series. Calculate the force...Ch. 10 - This blade is one of a series. What force is...Ch. 10 - A centrifugal water pump, with 15-cm-diameter...Ch. 10 - A centrifugal water pump designed to operate at...Ch. 10 - A series of blades, such as in Example 10.13,...
Ch. 10 - In passing through this blade system, the absolute...Ch. 10 - A centrifugal pump runs at 1750 rpm while pumping...Ch. 10 - A centrifugal water pump designed to operate at...Ch. 10 - Kerosene is pumped by a centrifugal pump. When the...Ch. 10 - In the water pump of Problem 10.8, the pump casing...Ch. 10 - Use data from Appendix C to choose points from the...Ch. 10 - Data from tests of a water suction pump operated...Ch. 10 - A centrifugal pump impeller having r1 = 50 mm, r2...Ch. 10 - A centrifugal pump impeller having dimensions and...Ch. 10 - An axial-flow fan operates in sea-level air at...Ch. 10 - Data measured during tests of a centrifugal pump...Ch. 10 - A small centrifugal pump, when tested at N = 2875...Ch. 10 - If the impeller of Problem 10.20 rotates between...Ch. 10 - At the outlet of a pump impeller of diameter 0.6 m...Ch. 10 - Typical performance curves for a centrifugal pump,...Ch. 10 - A pump with D = 500 mm delivers Q = 0.725 m3/s of...Ch. 10 - At its best efficiency point ( = 0.87), a...Ch. 10 - Using the performance curves in Appendix C, select...Ch. 10 - A pumping system must be specified for a lift...Ch. 10 - A centrifugal water pump operates at 1750 rpm; the...Ch. 10 - A set of eight 30-kW motor-pump units is used to...Ch. 10 - A blower has a rotor with 12-in. outside diameter...Ch. 10 - A centrifugal water pump has an impeller with an...Ch. 10 - Appendix C contains area bound curves for pump...Ch. 10 - Use data from Appendix C to verify the similarity...Ch. 10 - A centrifugal water pump has an impeller with...Ch. 10 - Catalog data for a centrifugal water pump at...Ch. 10 - A 1/3 scale model of a centrifugal water pump...Ch. 10 - Sometimes the variation of water viscosity with...Ch. 10 - A large deep fryer at a snack-food plant contains...Ch. 10 - Data from tests of a pump, with a...Ch. 10 - A four-stage boiler feed pump has suction and...Ch. 10 - A centrifugal pump operating at N = 2265 rpm lifts...Ch. 10 - A centrifugal pump is installed in a piping system...Ch. 10 - Part of the water supply for the South Rim of...Ch. 10 - Consider the flow system shown in Problem 8.94....Ch. 10 - Afire nozzle is supplied through 300 ft of...Ch. 10 - Performance data for a centrifugal fan of 3-ft...Ch. 10 - The performance data of Problem 10.57 are for a...Ch. 10 - Experimental test data for an aircraft engine fuel...Ch. 10 - Preliminary calculations for a hydroelectric power...Ch. 10 - Conditions at the inlet to the nozzle of a Pelton...Ch. 10 - A Francis turbine is to operate under a head of 46...Ch. 10 - A Kaplan (propeller with variable-pitch blades)...Ch. 10 - Francis turbine Units 19, 20, and 21, installed at...Ch. 10 - Measured data for performance of the reaction...Ch. 10 - For a flow rate of 12 L/s and turbine speed of 65...Ch. 10 - The velocity of the water jet driving this impulse...Ch. 10 - An impulse turbine is to develop 15 MW from a...Ch. 10 - An impulse turbine under a net head of 33 ft was...Ch. 10 - The absolute velocities and directions of the jets...Ch. 10 - A fanboat in the Florida Everglades is powered by...Ch. 10 - A jet-propelled aircraft traveling at 225 m/s...Ch. 10 - When an air jet of 1-in.-diameter strikes a series...Ch. 10 - The volume flow rate through the propeller of an...Ch. 10 - A typical American multi blade farm windmill has D...Ch. 10 - An airplane flies at 200 km/h through still air of...Ch. 10 - This ducted propeller unit drives a ship through...Ch. 10 - A model of an American multi blade farm windmill...Ch. 10 - A large Darrieus vertical axis wind turbine was...Ch. 10 - Show that this ducted propeller system when moving...Ch. 10 - This ducted propeller unit (now operating as a...Ch. 10 - What is the maximum power that can be expected...Ch. 10 - If an ideal windmill is operating at best...Ch. 10 - A prototype air compressor with a compression...Ch. 10 - Prob. 89PCh. 10 - We have seen many examples in Chapter 7 of...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
State if the members are in tension or compression. Prob. F6-8
Engineering Mechanics: Statics
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Replace the loading by an equivalent resultant force and couple moment acting at point A.
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Determine the scalar components Ra and Rb of the force R along the nonrectangular axes a and b. Also determine ...
Engineering Mechanics: Statics
One measure of a baseball pitcher's performance is earned run average or ERA. It is the average number of earne...
Applied Fluid Mechanics (7th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 4. A bladed fan rotor with an outside diameter of 12 in. and a 5 in. inside diameter runs at 1725 rpm. The width of each rotor blade is 1 in., from the blade inlet to outlet. The volume flow rate is steady at 230 ft/min. and the absolute velocity of the air at the blade inlet is purely radial, V₁. The blade discharge angle at the outlet is 30° as shown. (a) What would be a reasonable blade inlet angle, and (b) what is the power required to run the fan. (Pair = 2.38 × 10-3slugs ft3 309 1725 rpm 12 in. Q-230 ft/minarrow_forwardA centrifugal pump outer diameter equal to two times the inner diameter and running at 1200 rpm works against a total head of 75 m the velocity of the flow through the impeller is constant and equal to 3 m/s. The vane are set back at an angle of 30° at outlet. If the outer diameter of the impeller is 600 mm and width at out let is 50 mm, determine; 1- Vane angle at inlet. 2- Work done per second by imepller.arrow_forwardHow Vt=Vr × sin (70°) ? please provide explanation as fast as possible.arrow_forward
- 2. A wind turbine has the maximum power output at the rated speed of 12 m/s and a rotor diameter of 82 meters. The cut-in and cut-out speeds for this type of wind turbine are 4 m/s and 23 m/s, respectively. The table below shows the annual wind data near a potential site for setting up a wind farm using this type of wind turbine and the power coefficient of the wind turbine at the specific wind speed. The air density is 1.22 kg/m³. Wind speed (m/s) Power coefficient 7 Hours 1190 5 0.25 3000 10 0.5 2400 15 0.25 1700 20 0.1 400 25 50 30 20 (a). What is the maximum power output of this wind turbine, assuming Betz limit? (b). What is the average power output if the wind turbine is installed at this site?. (c). What is the capacity factor of the wind turbine at this site? (d). If a wind farm consisting of 100 such wind turbines is built at the site, how much energy does this wind farm generate in a year (in the unit of kWh)? (e). Is this a good site for using this particular type of wind…arrow_forwardProblem 1(5): A centrifugal pump transports water between two reservoirs. The pump has an outer diameter of 15 cm, an inner diameter of 8 cm, and a blade width of 2 cm and operates at 1750 rpm. If the water enters the pump axially at ẞ₁ = 45º¸ compute the volume flow rate, Problem 2(10): In the pump of problem 1, the water exits at B₂ 65° when the pump is driven at 1750 rpm. = Compute the minimum power required by the pump?arrow_forwardHow Vt=Vr × sin (70°) ? i need explanation regarding it. Please provide a solution within 10-20minarrow_forward
- 1 The internal and external diameters of the impeller of a centrifugal pump are 200 mm and 400 mm respectively. The pump is running at 1200 rpm. Forward blades make an angle of 150o at exit and at inlet the angle is 20o. The blade thicknesses at the inlet and outlet are 100mm and 70mm respectively. The hydraulic efficiency of the pump is 87%. Assume the water enters the impeller radially. i Draw neatly the outlet velocity diagram and the inlet velocity diagram. ii Find the Euler power of the pump. iii Find the net Head of the pump. Ans: (ii)140.65W; (iii) 43.42marrow_forwardWater is fed to an inward flow reaction turbine, running at 180 rpm with a velocity of flow of 3 m/s. The diameter and width of the wheel at inlet are 1 m and 135 mm, respectively. Assuming the velocity of flow to be constant and radial discharge at inlet and outlet, find, (a) work done per kN of water, (b) power developed by the turbine, (c) head of water on the turbine, and (d) hydraulic efficiency of the turbine. Also, draw velocity triangles showing all details.arrow_forwardA centrifugal pump impeller has an external diameter of 1.2 m and internal diameter of 0.8 m. The width of the impeller at outlet is 0.175 m and the blade angle at outlet is 65 degrees. The flow velocities at inlet and outlet are the same (Va1 = Va2). This pump delivers 1.55 m3/s of water at 210 rpm. For theoretical performance, calculate: 1-The flow velocity . 2-blade speed at outlet. 3-blade angle at inlet (in degrees). 4-the developed head. 5-The pressure rise across the impeller. 6-The number of blades . 7-The NPSH . %3Darrow_forward
- A two stage centrifugal pump is designed to discharge water at a total head of 70 m with an overall efficiency of 0.76. The pump runs at 2331.6 rpm. The actual head developed (per stage) is 65% of the theoretical head. The flow at the inlet is pure radial. The impeller at the exit has a diameter of D₂ = 0.219 m and a width of by 0.0216 m. The outlet blade angle is B₂ = 28. 4G 46% Determine: 1. The flow rate of the pump. 2. The output power of the two stage centrifugal pump. Take p=1000kg/m³ g= 9.81 m2/sarrow_forward3. The power output is 30 hp to a centrifugal pump that is discharging 900 GPM at which operates at 180 rpm against a head 120 ft., 220Volts, 3 phase, 60Hz. If the pump is modified to operate at 120 rpm, assuming its efficiency is constant, determine the discharge in GPM, the theoretical head it imparts to the liquid and the power input to the pump 4. A fan is used to provide ventilation in a tunnel requires a 3-kW electric motor to deliver 360 m³/hr. at a static pressure of 300mm of water has operated at speed of 500 rpm. It was later found out that the air to be delivered needs to be increased to a 420 m³/hr. If the fan size remains constant find the pressure in meters of water.arrow_forwardIn Francis turbine, the wheel peripheral velocity is (24m/s). The whirl velocity at inlet is (18 m/s). The flow velocity is (6m/s). The whirl at exit is zero. Assuming no other losses. Determine the head on the turbine and vane angle at inlet.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license