Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 10, Problem 90P
We have seen many examples in Chapter 7 of replacing working fluids in order to more easily achieve similitude between models and prototypes. Describe the effects of testing an air compressor using helium as the working fluid on the dimensionless and dimensional parameters we have discussed for compressible flow machines.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
(a) A model low speed centrifugal compressor (a “blower") runs at 430 rpm and delivers 10 m/s
of air against a pressure head of 60 mm of water. If the pump efficiency is estimated to be 80%,
how much power is required to drive the compressor?
(b) A geometrically similar compressor is made with a diameter 1.8 times the size of the model
and is required to work against a pressure head of 80 mm of water. Determine the operating
speed and the power needed to drive the compressor assuming dynamically similar condi-
tions apply.
CH, CQ and n are functions of CP. Draw the dimensionless performance curves of the turbine on a single graph by makingthe necessary scalings. (Fit the curve by using the excel program for drawing. Also give the values you used for plotting inthe table)
ÖN=5
Problem 4: The power P developed by a wind turbine is a function of diameter D,
air density p, wind speed V, and rotational rate @. Viscous effect is negligible.
(4a) Rewrite the above relationship in a dimensionless form;
(4b) In a wind tunnel, a small model with a diameter of 90cm, rotating at 1200 RPM
(revolution per minute), delivered 200 watts when the wind speed is 12m/s. The
data are to be used for a prototype of diameter of 50m and wind speed of 8 m/s.
For dynamic similarity, what will be (i) the rotational speed of the prototype turbine?
(ii) the power delivered by the prototype turbine? Assume air has sea-level density.
Chapter 10 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 10 - The geometry of a centrifugal water pump is r1 =...Ch. 10 - Find the resulting -groups when (a) D, , and Q or...Ch. 10 - Consider the centrifugal pump impeller dimensions...Ch. 10 - Dimensions of a centrifugal pump impeller areCh. 10 - Dimensions of a centrifugal pump impeller areCh. 10 - The blade is one of a series. Calculate the force...Ch. 10 - This blade is one of a series. What force is...Ch. 10 - A centrifugal water pump, with 15-cm-diameter...Ch. 10 - A centrifugal water pump designed to operate at...Ch. 10 - A series of blades, such as in Example 10.13,...
Ch. 10 - In passing through this blade system, the absolute...Ch. 10 - A centrifugal pump runs at 1750 rpm while pumping...Ch. 10 - A centrifugal water pump designed to operate at...Ch. 10 - Kerosene is pumped by a centrifugal pump. When the...Ch. 10 - In the water pump of Problem 10.8, the pump casing...Ch. 10 - Use data from Appendix C to choose points from the...Ch. 10 - Data from tests of a water suction pump operated...Ch. 10 - A centrifugal pump impeller having r1 = 50 mm, r2...Ch. 10 - A centrifugal pump impeller having dimensions and...Ch. 10 - An axial-flow fan operates in sea-level air at...Ch. 10 - Data measured during tests of a centrifugal pump...Ch. 10 - A small centrifugal pump, when tested at N = 2875...Ch. 10 - If the impeller of Problem 10.20 rotates between...Ch. 10 - At the outlet of a pump impeller of diameter 0.6 m...Ch. 10 - Typical performance curves for a centrifugal pump,...Ch. 10 - A pump with D = 500 mm delivers Q = 0.725 m3/s of...Ch. 10 - At its best efficiency point ( = 0.87), a...Ch. 10 - Using the performance curves in Appendix C, select...Ch. 10 - A pumping system must be specified for a lift...Ch. 10 - A centrifugal water pump operates at 1750 rpm; the...Ch. 10 - A set of eight 30-kW motor-pump units is used to...Ch. 10 - A blower has a rotor with 12-in. outside diameter...Ch. 10 - A centrifugal water pump has an impeller with an...Ch. 10 - Appendix C contains area bound curves for pump...Ch. 10 - Use data from Appendix C to verify the similarity...Ch. 10 - A centrifugal water pump has an impeller with...Ch. 10 - Catalog data for a centrifugal water pump at...Ch. 10 - A 1/3 scale model of a centrifugal water pump...Ch. 10 - Sometimes the variation of water viscosity with...Ch. 10 - A large deep fryer at a snack-food plant contains...Ch. 10 - Data from tests of a pump, with a...Ch. 10 - A four-stage boiler feed pump has suction and...Ch. 10 - A centrifugal pump operating at N = 2265 rpm lifts...Ch. 10 - A centrifugal pump is installed in a piping system...Ch. 10 - Part of the water supply for the South Rim of...Ch. 10 - Consider the flow system shown in Problem 8.94....Ch. 10 - Afire nozzle is supplied through 300 ft of...Ch. 10 - Performance data for a centrifugal fan of 3-ft...Ch. 10 - The performance data of Problem 10.57 are for a...Ch. 10 - Experimental test data for an aircraft engine fuel...Ch. 10 - Preliminary calculations for a hydroelectric power...Ch. 10 - Conditions at the inlet to the nozzle of a Pelton...Ch. 10 - A Francis turbine is to operate under a head of 46...Ch. 10 - A Kaplan (propeller with variable-pitch blades)...Ch. 10 - Francis turbine Units 19, 20, and 21, installed at...Ch. 10 - Measured data for performance of the reaction...Ch. 10 - For a flow rate of 12 L/s and turbine speed of 65...Ch. 10 - The velocity of the water jet driving this impulse...Ch. 10 - An impulse turbine is to develop 15 MW from a...Ch. 10 - An impulse turbine under a net head of 33 ft was...Ch. 10 - The absolute velocities and directions of the jets...Ch. 10 - A fanboat in the Florida Everglades is powered by...Ch. 10 - A jet-propelled aircraft traveling at 225 m/s...Ch. 10 - When an air jet of 1-in.-diameter strikes a series...Ch. 10 - The volume flow rate through the propeller of an...Ch. 10 - A typical American multi blade farm windmill has D...Ch. 10 - An airplane flies at 200 km/h through still air of...Ch. 10 - This ducted propeller unit drives a ship through...Ch. 10 - A model of an American multi blade farm windmill...Ch. 10 - A large Darrieus vertical axis wind turbine was...Ch. 10 - Show that this ducted propeller system when moving...Ch. 10 - This ducted propeller unit (now operating as a...Ch. 10 - What is the maximum power that can be expected...Ch. 10 - If an ideal windmill is operating at best...Ch. 10 - A prototype air compressor with a compression...Ch. 10 - Prob. 89PCh. 10 - We have seen many examples in Chapter 7 of...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature ...
Mechanics of Materials
When a simple turbine is used for mixing, the following variables are involved:
P = Power requirement [=]watt [...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Determine the normal stress in each member of the truss structure. All joints are ball joint, and the material ...
Introduction To Finite Element Analysis And Design
ICA 8-36
A 10-liter [L] flask contains 1.3 moles [mol] of an ideal gas at a temperature of 20 degrees Celsius [...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
The temperature of water at outlet.
Introduction to Heat Transfer
The rigid beam supports the load of 60 kN. Determine the displacement at B. Take E = 60 GPa, and ABC = 2 (10-3)...
Mechanics of Materials (10th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Cakulate the time rate of change of air density during expiration Assume that the lung (Fig. 3.11) has a total volume of 6000 ml, the diameter of the trachea is 18 mm, the airflow velocity out of the trachea is 20 cm/s, and the density of air is 1.225 kg/m. Also assume that lung volume is decreasing at a rate of 100 mL/s. Hello sir, I want the same solution, but in a detailed way and mention his data, a question, and a solution in detailing mathematics without words. Solution We will start from Eq. (3.24) because we are asked for the time rate of change of density. We are asked to find the time rate of change of air density; this suggests that Example 3.5 condis tions are representing a nonsteady flow scenario. In addition, we were told what the rate of change in the lung volume is during this procedure, further supporting the use of Eq. (3.24). pdV+ (3.24 ams Assume that at the instant in time that we are measuring the system, density is uniform within the volume of interest. This…arrow_forwardfluid mechanicsarrow_forwardAt low velocities (laminar flow), the volume flow Q through a small-bore tube is a function only of the tube radius R, the fluid viscosity u, and the pressure drop per unit tube length dp/dx. Using the pi theorem, find an appropriate dimensionless relationship.arrow_forward
- (b) The kinematic viscosity of a fluid used for model is one third of the kinematic viscosity of the fluid used for prototype. During testing of the model, if viscosity and gravity forces are predominant, find the scale ration, velocity ratio and discharge rationarrow_forwardSAE 30 oil at 60 °F is pumped through a 4-ft-diameter pipeline at a rate of 6750 gal/min. A model of this pipeline is to be designed using a 1-in.-diameter pipe and water at 60 °F as the working fluid. To maintain Reynolds number similarity between these two systems, what fluid velocity will be required in the model? Vm= i ft/sarrow_forwardGive me right solution with clear calculationsarrow_forward
- The true optionarrow_forwardThe power input P to a centrifugal pump is assumed to be a function of the volume flow Q, impeller diameter D, rotational rate Ohm, the density rho, and viscosity mu of the fluid. Rewrite this as a dimensionless relationshiparrow_forwardAir is compressed by a compressor in steady-state operation, i.e. the inlet mass flow rate qm is constant in time. The compressor is airtight. The area of the inlet and outlet cross-section is A and AOUT, respectively. The outlet-to-inlet density ratio is PouT PIN the outlet-to-inlet mass flow rate ratio is 9m-OUT/9m-IN- What is the outlet-to-inlet volume flow rate ratio? 9V-OUT/av-IN =? Select one: a. 9V-OUT/av-IN = (A OUT'A IN) (POUT PIN b. 9V-OUT/av-IN = PIN/POUT C. 9V-OUT/av-IN = 9m-OUT/ 9m-IN d. 9V-OUT/av-IN=AOUTAINarrow_forward
- In Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.arrow_forwardP.2 In an automobile engine, as the valve opens to a cylinder, the piston moves down and air enters the cylinder. Fuel follows, and is burned. Thereafter, the combustion gases are discharged as the piston moves up. On a very short time scale, say a few microseconds, would the cylinder be considered an open or closed system? Repeat for a time scale of several seconds.arrow_forwardA 1:7 scale model simulates the operation of alarge turbine that is to generate 200 kW with a flowrate of 1.5 m3/s.What flow rate should be used inthe model, and what power output is expected?(a) Water at the same temperature is used in bothmodel and prototype.(b) The model water is at 25°C and the prototypewater is at 10°C.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Unit Conversion the Easy Way (Dimensional Analysis); Author: ketzbook;https://www.youtube.com/watch?v=HRe1mire4Gc;License: Standard YouTube License, CC-BY