Suppose you are using a push-loaded scraper with a heaped capacity of 31 cy. Assuming an average load of 96% of heaped capacity results in an average load of 29.76 cy. If the material to be hauled is a sandy clay with a swell factor of 0.80, what is the volume carried in bank cubic yards?

Suppose you are using a push-loaded scraper with a heaped capacity of 31 cy. Assuming an average load of 96% of heaped capacity results in an average load of 29.76 cy. If the material to be hauled is a sandy clay with a swell factor of 0.80, what is the volume carried in bank cubic yards?

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.36P: Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in...

See similar textbooks

Related questions

Q: 4.1. The storm hydrograph given bellow was measured at a point in a river at 2-hr intervals from an…

A: Step 1:4.1 (a) Calculate the volume of direct runoff:The direct runoff can be calculated by finding…

Q: Consider solving for the equation of the elastic curve (i.e., function for deflected shape) for the…

A: SolutionBoundary Conditions and Continuity ConditionsBoundary Conditions:At point A (x1 =…

Q: What is the pore water pressure in kPa in Point (A) for the Sandy soil layer with the permeability…

A: The problem is asking for the pore water pressure at a certain point in a sandy soil layer. The pore…

Q: Identify all the zero force members in both trusses.

A: Step 1:According to inspection method, a joint where three members meet without any external load…

Q: Please solve and show all of your work.

Q: Define the following terms: Aliquot part Retracement survey Original survey Adverse possession

A: An Aliquot Part is a term used in land surveying that refers to a portion of a larger whole. It is…

Q: | As you drive on a straight, two-lane rural road with a speed limit of 55 mph (design speed 70 mph)…

A: Given: v0=70mph=70hourmile⋅1mile5280ft⋅3600s1hour≈102.67ft/sd=683fta=−11.2ft/s2 Please note that…

Q: Problem 5: Determine the user equilibrium flows USE THE PROBLEM STATEMENT BELOW TO ANSWER THE…

A: Step 1:Step 2:Step 3:Step 4:

Q: A 1900-m3 water tower has been cleaned with a chlorine solution. The vapors of chlorine in the tower…

Q: System is released from rest, determine the speeds of both masses after B has moved 1.7 m. (read…

A: Approach to solving the question: Newton's second law equations. Detailed explanation:Note: We can…

Q: 2 to 13-37 Refer to Figs. P13-22 to P13-37. Construct the shear force and the bending moment…

A: Making the uniformly distributed load into the concentrated load into a concentrated load Always…

Q: be Example: Calculate the wind set-up and wave height for a reservoir with 8 km fetch length. The…

Q: The answer depicted is incorrect, any help would be appreciayed thanks!

A: First, we determined that there were roughly 2,835,664 Equivalent Single Axle Loads (ESALs) during…

Q: Select the most economical A992 steel interior building column based upon thefollowing compressive…

A: Step 1: Tributary Area [Tributary Area=15ft×20ft=300ft2]Loadings:2nd Floor:- Live Load: (100psf)-…

Q: Use the method of virtual work to determine the vertical and horizontal components of deflection at…

A: Step 1: Step 2:Step 3:Step 4:

Q: Given: Wonderboom catchment (A = 150 km2) in Pretoria North shown in Fig. 2. The slope of the…

Q: Show detailed solution, I have a chatgpt account I can see if it was generated from there. Bartleby…

A: Apply the continuity equation between sections 1 and 2:A1 × V1 = A2 × V2(π/4) × d1² × V1 = (π/4) ×…

Q: Civil Engineering Question

A: Force Calculations and Equilibrium in the Trailer SystemThe diagram can be analyzed using principles…

Q: I need detailed help solving exercise 1 from Engineering Math. Step by step, please.

Q: Please help solve, provide all units and steps and highlight answers.

Q: A short post, 150 mm by 150 mm, of Douglas fir, is reinforced by the addition of two ASTM A36 steel…

A: The cross-sectional area of the wood (Aw) can be calculated using the formula for the area of a…

Q: The numbers in the bottom corner are the answers.

A: SOLUTION:

Q: In what ways might the concepts presented in electricelectron application be applied by you either…

A: Personal Applications:Energy Efficiency:Learning how circuits and electrical components work can…

Q: The 240-kg lunar Lander is descending onto the moon's surface with a velocity of 9 m/sec (read…

Q: 1. Solve the following differential equation: subject to the initial condition y(0) = 2 dy = ysin(x)…

Q: Subject: Structural Theory Topic: Area-Moment Method Draw diagram and handwritten solutions. Box…

Q: Need help, please show all work, steps, units and round to 3 significant figures. Thank you!

Q: Thumbs-up will be given. Please write the complete solutions and Write Legibly. Compute the…

A: To calculate the maximum flexural stress in a simply supported beam with a uniform load, we can use…

Q: find the Fourier series represen- tation of the given function over the indicated fundamental…

A: Determine the Fourier CoefficientsThe Fourier series for a function f(x) defined over the interval…

Q: Note: Please provide a concise working out with a handwritten solution only, ensuring no AI…

A: Step 1:Step 2:Step 3:Step 4:

Q: Please show all of your work, Thank you for your help!

A: Given Data:Development Length CalculationConclusionThe calculated development length of 58.8 in.…

Q: Answer the following questions regarding the ideal settling tank and particle settling [Pertinent…

A: I hope this is helpful.

Q: A horizontal curve with radius equal to 220 m and intersection angle of 126° is to be realigned by…

A: First, we need to calculate the intersection angle (Δ) of the new curve. The intersection angle of…

Q: The integrals arise when finding the Fourier series expansion of eax over the interval -L< x < L.…

A: Set up the integral:I=∫−ππeaxsinnxdxIntegration by parts:Use integration by parts, where:Let…

Q: (read image)

Q: Prepare a table of end areas versus depths of fill from 0 to 20 ft by increments of 2 ft for level…

A: The problem is asking us to calculate the end areas for different depths of fill for a level…

Q: A study of freeway flow at a particular site has resulted in a speed-density relationship as…

A: I hope this is helpful.

Q: Problem 18-10 in Roess, Prassas, McShane, 5 th ed.An intersection approach has a demand volume of…

A: The degree of saturation (X) is the ratio of the demand volume (v) to the saturation flow rate (s)…

Q: 2. Using virtual work method, determine a The rotation of point A. The modulus of elasticity is…

A: Step 1:Step 2: Step 3: Step 4:

Q: Refer to Sketch #2. Determine the reactions and moment at support A. Show the magnitude and…

Q: Note: - I've posted this question multiple times and I'm getting poor quality answers!. Also if you…

A: Step 1: Identify Support Reactions:Clue: A - roller supportB - Fixed SupportC - Roller-Fixed Support…

Q: Irrigation and drainage engineering question Q/ The following data is from the cylindrical…

A: Step 1:Step 2: Step 3: Step 4:

Q: A simply supported beam is loaded and supported as shown in the figure. a. Draw the shear and…

A: Step 1: Step 2: Step 3: Step 4:

Q: Given an azimuth from point A to point B of S36o15'30"E, and a horizontal distance from point A to…

A: Step 1: To calculate the departure (ΔX), we use the formula: ΔX=D×sin(θ) Where:D is the horizontal…

Q: (read image)

Q: Given that the reaction at A is 54.33 kips, the reaction at B is 54.47 kips. Draw the Shear and…

A: Step 1: Step 2: Step 3: Step 4:

Q: The safety factor for allowable Dead Load bearing capacity is: Group of answer choices 3 2 5…

A: The safety factor for allowable Dead Load bearing capacity is typically 2. This means that the…

Q: Need help with Structural Analysis problem, thanks!

Q: 3. Compare batch culture and continuous culture. Draw diagrams for each of them. Describe cell…

A: Batch vs. Continuous Culture Batch CultureDescription: A closed system where a fixed volume of…

Question

AI-Generated Solution

AI-generated content may present inaccurate or offensive content that does not represent bartleby’s views.

Unlock instant AI solutions

Tap the button
to generate a solution

Click the button to generate
a solution

SEE SOLUTION

Similar questions

2. Determine the balanced hauls and indicate the direction of haul for the mass diagram shown below. The LPH is 4,000 ft. Also, show on the profile what cut sections will be hauled to what fill sections, and indicate any borrow or waste sections. Calculate the average haul distance for each. balanced haul.. 75000 50000 25000 0 -25000 -50000 -75000 0 Distance along centerline, ft 14000 15000
A bottom dump hydraulic shovel with a 5 cubic yard heaped capacity bucket is excavating in hard clay. The depth of the excavation is 12 feet. The shovel has a maximum rated digging depth of 34 feet. The haul units can be positioned so that the swing angle is 60 degrees. The job efficiency is 50 minutes per hour. Find the expected production per hour.
Estimate the hourly production in bank measures of a hydraulic shovel loading sand and gravel into trucks. The machine is equipped with a front dump bucket having a heaped bucket capacity of 5.2 Lm³. Average swing angle is 60 degrees. The bucket fill factor is 0.9, job efficiency is 1.0, and load factor is 0.85.
Based on the scraper specifications in Table 8.1 and the performance charts in Figs. 8.7 and 8.8, and for haul conditions as stated here, analyze the probable scraper production. How many scrapers should be used and what will be the production in bcy per hour? The material to be hauled is cohesive. It has a swell factor of 0.77 and a unit weight of 2,940 lb/bcy. The expected rolling resistance for the well-maintained haul road is +4%. Assume a 0.85-min load time will yield an average load of 89% of heaped capacity. To account for both acceleration and deceleration, use an average speed of 5 mph over a distance of 200 ft. Use a 45-min hour efficiency factor. The total length of haul is 3,000 ft and has the following individual segments when moving from cut to fill: 600 ft 5% grade 2,200 ft 2% grade 200 ft –4% grade
I need the answer as soon as possible
4. Estimate the production in compacted cubic yards per hour of a tamping foot, wheel-tractor-towed, that is compacting lifts of 8 inches with an efficiency of 85%. The effective roller width is 12 ft, and 10 passes are projected to complete the job.
1. A contractor is using a tracked loader to backfill a building foundation. The loader is equipped with a bucket that has a rated heaped capacity of 1.4 cubic yards. The static tipping load for the loader is 11,570 pounds. The soil being used for the backfill is a rock dirt mixture weighing 2,950 pounds per loose cubic yard. The average travel distance for the loader is 125 feet one way. The average loader speed when loaded is estimated to be 1.5 miles per hour and when empty 2.2 miles per hour. What is the estimated productivity of the loader in loose cubic yards per hour, if the contractor plans an operational efficiency of 45 minutes per hour?
A hydraulic excavator with a 2 cubic yard heaped capacity bucket is excavating in common earth. The depth of the excavation is 8 feet. The excavator has a maximum rated digging depth of 16 feet. The excavated material will be positioned so that the swing angle is 75 degrees. The job efficiency is 55 minutes per hour. Find the expected production per hour.
An excavator bucket has a heaped capacity of 6.2 CY and a bucket fill factor of 0.85. What is the bucket capacity?a. 5.35 CY b. 6.1 CY c. 7.3 CY d. 5.27 CY
Engineers have observed that the axial capacity of piles driven into saturated clay improves with time. What physical mechanisms cause this behavior? and Why don’t we observe it in piles driven into clean sands?
Note:hand written solution should be avoided.
Solution