Thumbs-up will be given. Please write the complete solutions and Write Legibly. Compute the maximum flexural stress developed in a 4.3m simple timber beam with a rectangular section of b=92mm and d=196mm with a downward uniform load of 88KN/m. The modulus of elasticity of wood is 7310MPa. Express your answer in MPa in 2 decimal places.

Thumbs-up will be given. Please write the complete solutions and Write Legibly. Compute the maximum flexural stress developed in a 4.3m simple timber beam with a rectangular section of b=92mm and d=196mm with a downward uniform load of 88KN/m. The modulus of elasticity of wood is 7310MPa. Express your answer in MPa in 2 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Read the question carefully and give me right solution with clear calculations.
Minimum of 3 decimal places in all computations. Show your solution on paper
Show complete solution. Answer Choices: 2pcs 3pcs 4pcs 5pcs
A 200 mm × 220 mm timber post is subject to an unknown axial compressive load(F) that is eccentric to both principal axes as shown below. If the axial stress is2.4 MPa then:(a) What is the compressive load?(b) What are the applied moments in the x and y directions?(c) What are the moments of inertia in the x and y directions.(d) At what corner does the maximum stress occur? State whether it is tensile or compressive?` (e) Calculate the maximum stress at the corne
Please answer this. Thank you
A piece of wood with a triangular cross section contains a rubberized joint to aangle θ with the vertical. The stress that the wood resists in tension is 20 MPa, the rubber resists10 MPa in tension and 12 MPa in shear. If θ = 60, determine the maximum load P.
A simply supported beam is reinforced with 4-ø28 mm at the bottom and 2-ø20 mm at the top of the beam, Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'=28 MPa, fy=415 MPa. Assume bars laid out in single layer. Calculate the following if the limitin tensile steel strains is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = _____________mm Design strength of the beam section to the nearest whole number =____________ kN-m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____________ kN/m (to the nearest whole number)
4. Steel and aluminum plates are used to reinforced 150 x 300 mm timber beam. The three materials are fastened firmly as shown so that there will be no relative movement between them. Given the following material properties, determine the safe resisting moment of the beam in KN.M. Allowable bending stress, Fb Modulus of Elasticity, E Steel = 137MPa %3D Steel = 217MPa Aluminum = 97 MPa Aluminum = 87 MPa %3! !3! Wood = 27 MPa Wood = 22 MPa 50mm CTEEL 150mm 300mm WeOD A LUAINUm 60mm
The timber member has a cross-sectional area of 1653 mm2 and its modulus of elasticity is 12.9 GPa. Compute the change in the total length (in mm) of the member after the loads shown are applied if x = 1.67, y = 3.87, and z = 3.65. Round off the final answer in two decimal places. 40 kN 35 kN 20.8 D A B•
ANSWER THE PROBLEM QUESTION AND SHOW YOUR SOLUTION CLEARLY AND BOX THE FINAL ANSWER. USE 2 DECIMAL PLACES
1. A single span beam having an unsupported span of 20m carries a uniform load of "W" kN/m throughout its span. The beam has a cross section of 150 mm x 600 mm. Allowable bending stress of the wood is F, = 12.4 MPa with a modulus elasticity of 13800 MPa. a. Compute the allowable bending stress with the size factor adjustment. b. Compute the allowable bending stress with slenderness factor adjustment. c. Compute the "W" that the beam could carry.
i will upvote who can answer this