A roof truss and the detail of the connection at joint B are shown in the figure. Angle sections with the thicknesses shown in the figure are members BC and BE. Shear in the rivets has a working stress of 70 MPa, while bearing stress due to the rivets has a working stress of 140 MPa. To fasten the following members to the gusset plate, how many 19-mm-diameter rivets are required: (a) BC; and (b) BE? 1.45 14mm-thick gusset plate 13mm-thick angle bar 6m 6mm-thick BE angle bar 3m 3m 3m 3m PBC 100KN 200KN 100KN

A roof truss and the detail of the connection at joint B are shown in the figure. Angle sections with the thicknesses shown in the figure are members BC and BE. Shear in the rivets has a working stress of 70 MPa, while bearing stress due to the rivets has a working stress of 140 MPa. To fasten the following members to the gusset plate, how many 19-mm-diameter rivets are required: (a) BC; and (b) BE? 1.45 14mm-thick gusset plate 13mm-thick angle bar 6m 6mm-thick BE angle bar 3m 3m 3m 3m PBC 100KN 200KN 100KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed to unyielding supports at the top (point A) and bottom (point C) ends. If there is a temperature rise of 50°C, calculate the compressive force induced in the rods (ABC). Note: For steel (E = 200 GPa, as = 11.7 x 106 °C) and for brass (E = 105 GPa, qb= 20.9 x 10-6/ °C). 250 mm 300 mm A B -30-mm diameter -50-mm diameter
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
A steel plate is used to connect a column and beam as shown in Fig. 3. The connection betweenthe beam and the plate is fillet welds. Given Q=150kN and Mx= -5kN-m (applied at centriod ofthe welds between the beam and the plate), determine maximum shear stress in the welds betweenthe beam and the plate.
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 50 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.7 ksi. Brass segment (2) has an outside diameter of 0.85 in., a wall thickness of 0.13 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.0 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
For the beam shown in Figure (1), determine: a) The stresses in rods AB and BC. The cross-sectional area of rod AB is 155 mm2, and for BC is 200 mm?. b) The average shear stress in bolt at pin A. 1500 N S5 15 m 600 N/mt m- -3 m- Figure (1)
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
A steel latch is 6 mm thick. A force F of 3000 N is uniformly distributed as shown below. Do not consider the stress concentration! a) Determine the principal stresses at Scction B-B?. b) Determine the principal stresses at point A? 3 kN Y R30 L, A 125 09
Two steel rods are welded together (see figure);the seam is oriented at angle θ = 50°. The stresses onthe rotated element are σ x1 = 10 ksi, σy1 = -12 ksi,and τx1y1 = -5 ksi. Find the state of plane stress onthe element if it is rotated clockwise to align the x1axis with the longitudinal axis of the rods.
Q4: For the figure below, determine the principal stresses and show them on a sketch of a properly oriented element. Also, find the maximum shear stresses and show them on a sketch of a properly oriented element. (Consider only the in-plane stresses.) -30MPA 90 MPa -34MPA
Load P is applied to joint D and the temperature increases by 50 °F. There are two steel (E = 29*10^6 psi; a = 6.5*10^-6/°F) AD and DC and a bronze (E = 16*10^6 psi; a = 9*10^-6/°F) BD with a length of 50 inches. Each bar is a 0.75 inch diameter. Find the deformation of every rod, the displacement at D, and the stress in each rod.