Two plates with a thickness of 35mm, width of 160mm, and length of 200mm are joined ogether by a pin with a diameter of 60mm. 200 mm 60 mm 160 mm 1 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250MPA and the shear strength of the pin is 100MPA. suppose that P is 140kN, the Modulus of Elasticity is 200GPA, and the Poisson's ratio is .3. 2) Determine the change in length of each plate. 3) Determine the change in width of each plate. ) Determine the change in thickness of each plate.

Two plates with a thickness of 35mm, width of 160mm, and length of 200mm are joined ogether by a pin with a diameter of 60mm. 200 mm 60 mm 160 mm 1 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250MPA and the shear strength of the pin is 100MPA. suppose that P is 140kN, the Modulus of Elasticity is 200GPA, and the Poisson's ratio is .3. 2) Determine the change in length of each plate. 3) Determine the change in width of each plate. ) Determine the change in thickness of each plate.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place, however, a gap of A = 0.35 in. exists between the two pipes. Bronze pipe (1) has an elastic modulus of E1 = 16,000 ksi, a cross-sectional area of A1 = 2.66 in.?, and a length of L1 = 6.7 ft. Aluminum alloy pipe (2) has an elastic modulus of E2 = 10,000 ksi, a cross-sectional area of A2 = 1.37 in.2, and a length of L2 = 10.2 ft. If bolts are inserted in the flanges and tightened so that the gap at B is closed, determine: (a) the normal stresses produced in each of the members. (b) the final position of flange B with respect to support A. L2 В (1) Answer: (a) 01 = ksi 02 = ksi (b) ÕB/A = in.
The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between the jaws. In this case; a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure. b) Show the distribution of normal stresses across the section height. (draw) c) Since the clamp material has tensile strength (apull) safety = 50MPA and compression safe stress (opress) safety = 80MPA, what is the great compressive load (P) that can be applied without damaging the a-a section? %3D %3D (Please solve in detail and according to engineering rules.) Material mechanics Sectional view a-a - 20mm T. 183mm 40mm
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.45 in., a wall thickness of 0.15 in., a length of L₂ = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ L2 TB (1) Answer: (a) TB= (b) T₁ = T2= (c) OB= B lb-ft lb-ft lb-ft rad (2) C
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Мра. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm F F mm. 50 mm 340 mm
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 50 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.7 ksi. Brass segment (2) has an outside diameter of 0.85 in., a wall thickness of 0.13 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.0 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B and bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest hundredths.
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assumea = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a (1) (3) A B (2) Answer: P = i kN
Q4: For the figure below, determine the principal stresses and show them on a sketch of a properly oriented element. Also, find the maximum shear stresses and show them on a sketch of a properly oriented element. (Consider only the in-plane stresses.) -30MPA 90 MPa -34MPA
Load P is applied to joint D and the temperature increases by 50 °F. There are two steel (E = 29*10^6 psi; a = 6.5*10^-6/°F) AD and DC and a bronze (E = 16*10^6 psi; a = 9*10^-6/°F) BD with a length of 50 inches. Each bar is a 0.75 inch diameter. Find the deformation of every rod, the displacement at D, and the stress in each rod.
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d. = 1.5 in.; both have length. L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN