The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear strain in the shear plane of the bolt when the applied force P = 750 kN is removed. Note: The bolt is made from a material having a shear stress-strain diagram as follows T (MPa) A { 600 400 5 50 y (10³ rad)

The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear strain in the shear plane of the bolt when the applied force P = 750 kN is removed. Note: The bolt is made from a material having a shear stress-strain diagram as follows T (MPa) A { 600 400 5 50 y (10³ rad)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Someone can help me with these. I'm stock, please.
Question 4. Three wires are used to suspend the plate shown. Aluminium wires are used at A and B with a diameter of 3 mm and a steel wire is used at C with a diameter of 2 mm. Knowing that the allowable stress for aluminium (E = 72 GPa) is 96 MPa and that the allowable stress for steel (E = 200 GPa) is 124 MPa, determine the maximum load P that may be applied. L L P B
Portions of a x-in. square bar have been bent to form the two machine components shown. Knowing that the allowable stress is 18 ksi, determine the maximum load that can be applied to each component. (a) 1 in. (b) The maximum load that can be applied to component (a) is The maximum load that can be applied to component (b) is lb. lb.
i need the answer quickly
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.71 in and an elastic modulus of 2050 ksi. Bar (2) has a cross-sectional area of 1.019 in? and an elastic modulus of 3910 ksi. Assume L-20 in. Lyn47 in. Q-6 kips. P-3.6 kips, and R-13.2 kips. Determine the horizontal deflection of end Crelative to end A. (1) (2) Answer: UCIA - in.
A small aluminum alloy [E = 79 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross- sectional dimensions of the tee shape are b = 16 mm, d = 24 mm, and t = 8 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage - d D E H b Answer: P= i N
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm mm. 50 mm 340 mm
2.)
Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 9- MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is P/2 - F 8 mm 8 mm ↓ 12 mm P
In the figure shown, determine the normal stresses at AD + and BC • shearing stress at bolt D + , bearing stress of AD at bolt D bearing stress of member EDC at bolt D All bolts Ø16mm 04 n 0.25 m 02 m |D 20kN E 10 x 50 mm 8 × 36 mm
The two wooden boards shown in the figure are connected by a 0.5 in. diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D  2 in. and d 5/8 in. The nut is tightened to cause a tensile stress of 9,000 psi in the bolt. Determine the bearing stress MPa between the washer and the wood
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. Thesteel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assume a = 4.1 m, b = 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? (1) P (3) B (2) Answer: P = 117.7 kN