Which stress element below correctly shows the normal and stress at point H? H O (1) B A H F B D Write the letter of your choice for the answer in the blank. Use Capital letter (A, B, ...., J). E G K

Q: Figure 2.5.3 - Qu Inside perimeter Outside perimeter Centreline

A:

Q: What is wrong with the picture at right?" (<25 words) YES! Safel NOI Unsafel

A: A picture including of two images where different cases of cylinders were given.

Q: Whose responsibility is it to create the as-built BIM? Architect / Engineer to complete designers'…

A: This question is related to the Building design from Civil Engineering.

Q: Draw the sectional front view (front section) and draw the orthographic projection (sideand top…

A: Asked: To draw the orthographic projection views of the given object.   The orthographic projection…

Q: 17. COMPLETE THE FOLLOWING INSERT CODE IN INCHES: MG 43 18. COMPLETE THE FOLLOWING INSERT CODE IN…

A: 17. It is made up of  CNMG432       1/2" inner circle , 1/32" corner circle and 80°  Diamond woth 0°…

Q: Show the quadrants of a circle and within the circle show  S 30° W

A:

Q: What is Moment Magnitude?

A: MOMENT MAGNITUDE : -Moment Magnitude is a most commonly used to measure the size of microseism and…

Q: Wembley Stadium

A: Wembley Stadium is located in London and know for holding important football matches. The design of…

Q: Determine how far is the centroid of the given cross section above the base. 6-504 2-50" 9.0" 6.5"…

A:

Q: Assignm R= Station 18+26 18+00 17+00 16+00 15+68 3: For Arc 0 Deflection Angle (DMS) 0°0'0" Chord…

A: Horizontal Curve :  In order to transition between two tangent strips of road, a horizontal curve is…

Q: A wall has an area of 75 sq ft. Find to the nearer hundredth square meter thearea of the wall.

A: Given:- area = 75 sq ft To find:- Nearer hundredth square meter thearea of the wall.

Q: installed in the front lawn and along one side and seeded the remain- der with 3.5 pounds per 1,000…

A:

Q: A blueprint for the floor of a natural history museum is shown the scale of the museum to the…

A: Given- A blueprint for the floor of a natural history museum. scale used=20 yards to 1 inch…

Q: Figure 2. Inside perimeter Outside perimeter Centreline

A: Inside perimeter :Length×2+Breadth×2+2×2'+3'24'3''×2+12'×2+2×2'+3'=79'6''

Q: Please explain step 4 and 5

A: Grade: g1 =3%  g2 =-4% Station of intersection = 3+400 Elevation of intersection = 7600 m Station…

Q: what about this part  two ??? and the height is 2.5 not 2 , very bad service

A: Y1 = 2.5 mq =5 m³/s/m

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.