The rectangular bar shown is connected to a support bracket with a 16 mm diameter pin. The width of the rectangular bar is 60 mm and its thickness is 25 mm. The bearing stress in the bar cannot exceed 200 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket.just bearing stress in the rectangular bar. Rectangular bar Support - bracket

The rectangular bar shown is connected to a support bracket with a 16 mm diameter pin. The width of the rectangular bar is 60 mm and its thickness is 25 mm. The bearing stress in the bar cannot exceed 200 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket.just bearing stress in the rectangular bar. Rectangular bar Support - bracket

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A solid brass shaft is loaded as shown below by two torques TB segments are LAB = 750 mm and LBC =…

Q: Determine the maximum permissible value of T provided the allowable shearing stresses in brass and…

A: ζb=70 MPaζs=110 MPaGb=80 GPaGs=40 GPa di=70 mmd0=90 mm

Q: The belt shown has a width of 43 mm and a thickness of 6 mm. [P1= 30 kN, P2= 6 kN, P3= 14 kN, P4= 14…

A: the width of the belt (b)=43 mm, thickness (t)=6 mm.P1=30 kN, P2=6 kN, P3=14 kN, P4=14 kN.…

Q: The member shown in the right side consists of the steel rod AB that is screwed into the end of the…

Q: The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a…

A: Figure is as shown

Q: the seven bolts connection in the figure below, the diameter of the bolt is D= 1 in, the width of…

Q: The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free.…

Q: The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are…

A: J1 = π32×0.554 J2 = π32×0.354-0.234

Q: Taking into account only the effect of normal stresses, determine the strain energy of the prismatic…

Q: The rigid beam is supported by the two bars shown in a horizontal position before the load P is…

Q: hat have an outside diameter of 135 mm and a wall thickness of 9 mm. Determine the normal stress in…

A: From a given question it is required to calculate stresses in each member of truss.

Q: When the normal stresses are at their maximum or minimum values, the shear stresses are zero. We can…

A: 1- Yes when normal stresses are maximum or minimum, then at that element shear stress is zero. 2-…

Q: Question 4. Three wires are used to suspend the plate shown. Aluminium wires used at A and B with a…

Q: 1 1 Portions of a x-in. square bar have been bent to form the two machine components shown. Knowing…

A: A square section of dimension in2 is bent into two sectionsSquare sectionDiamond sectionThe…

Q: The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear…

A: Given data in question Load 750 kN Diameter 32 mm To find out Permenant strain

Concept explainers

Pressure and Stress

Question

100%

The rectangular bar shown is connected to a support bracket with a 16 mm diameter pin. The width of the rectangular bar is 60 mm
and its thickness is 25 mm. The bearing stress in the bar cannot exceed 200 MPa. Determine the maximum value of Pmax that can be
supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the
support bracket.just bearing stress in the rectangular bar.
Rectangular bar
Support
bracket

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

N = 7
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.45 in., a wall thickness of 0.15 in., a length of L₂ = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ L2 TB (1) Answer: (a) TB= (b) T₁ = T2= (c) OB= B lb-ft lb-ft lb-ft rad (2) C
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assumea = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a (1) (3) A B (2) Answer: P = i kN
A stress developed if the applied force is parallel to the resisting area refers to: O tangential O bearing O normal. O simple
When the temperature is at 30°C, the steel pipe fits snugly between the two fuel tanks. When fuel flows through the pipe, it causes the temperature to vary along the pipe as T = (3x² 20x + 120)°C. Calculate the normal stress developed in the pipe. Assume each tank provides a rigid support at A and B. a=12X10-6/°C - 150 mm 10 mm- Section a - a -6 m a a B
Load P is applied to joint D and the temperature increases by 50 °F. There are two steel (E = 29*10^6 psi; a = 6.5*10^-6/°F) AD and DC and a bronze (E = 16*10^6 psi; a = 9*10^-6/°F) BD with a length of 50 inches. Each bar is a 0.75 inch diameter. Find the deformation of every rod, the displacement at D, and the stress in each rod.
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN