The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assume a = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a C. (1) e (3) A B (2) D Answer: P= i 117.7 kN

The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assume a = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a C. (1) e (3) A B (2) D Answer: P= i 117.7 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage D E H b. Answer: P = i 29254 N
Answer all.a.A mild steel flat of width b= 150 mm, thickness t = 20 mm and length L= 6000 mm carries an axial pull P = 300 kN. If modulus of elasticity of mild steel is 200 GPa and Poisson’s ratio is 0.25, calculate the change in length, width and thickness of the flat. B.A stepped bar made of brass is subjected to axial loads as shown in the below figure. Determine the total change in length of the bar. Take E =100 GPa.figure is attached C.A thin cylinder of external diameter 820 mm, length 3 m and wall thickness of 10 mm is subjected to an internal pressure of 2.5 N/mm2 . Determine the change in diameter and length. Take Young’s modulus = 2×105 N/mm2 and Poisson’s ratio = 0.25.
A high-strength steel bar used in a large crane has a diameter d = 3.00 in. (see figure). Ⓡ The steel has a modulus of elasticity E = 29 x 105 psi and Poisson's ratio is y = 0.27. Because of clearance requirements, the diameter of the bar is limited to 3.002 in. when it is compressed by axial forces. What is the largest compressive load Pmax that i permitted? Assume that the material behaves linearly elastically. (Enter the magnitude in lb.) lb
1. The assembly has the diameters and material makeup indicated. If it fits securely between its fixed supports when the temperature is T; = 70°F, determine the average normal stress in each material when the temperature reaches T2 = 130°F. 304 Stainless steel - 2014-T6 Aluminum -C 86100 Bronze A 12 in. 8 in. D C 4 in. -4 ft- 6 ft- 3 ft
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
The steel pipe shown has an outside diameter of 175 mm, a wall thickness of 18 mm, an elastic modulus of E = 200 GPa, and a coefficient of thermal expansion of ? = 11.7 x 10-6/°C. Using a = 335 mm, b = 870 mm, and ?= 60°, calculate the normal strains at Hand K after a load of P= 45 kN has been applied and the temperature of the pipe has been increased by 35°C O 16 mm, an e load of P= 45 kN has been applied and the temperature of the pipe has been increased by Answers: EH = Ek= H K με με
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
A load P is applied to a steel component which is supported an aluminum plate into which a 12 mm diameter hole has been drilled. Knowing that the maximum allowable shearing stress is 86.5 MPa in the steel and 160 MPa in the aluminum plate, determine the largest load which may be applied to the steel component. Provide your answer in kN with precision to two decimal points. 10 mm Answer: 12 mm 40 mm P 8 mm
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assumea = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a (1) (3) A B (2) Answer: P = i kN
A steel crane hook has a yield strength of 386MPa and Young's modulus of 210 GPa, where a=15mm, b=32mm, and c= 5mm. The crane hook has a thickness of 8.1mm.1. Determine the point at which yielding will occur first as the load is increased from 0 to 250N in increments of 50N2. Determine the load at which yielding will begin.3. Determine the profile of longitudinal stress over the critical cross section for a load of 200N.
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN