Problem 01.054- Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at Cand 12-mm-diameter pins are used at B and D. The ultimate shear stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. A A Front view 160 mm. D B -18 mm B Top view 120 mm largest load P that can be applied at A is) 29AP 2.328 KN D 6 mm $1 B Side view

Problem 01.054- Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at Cand 12-mm-diameter pins are used at B and D. The ultimate shear stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. A A Front view 160 mm. D B -18 mm B Top view 120 mm largest load P that can be applied at A is) 29AP 2.328 KN D 6 mm $1 B Side view

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The rectangular bar shown is connected to a support bracket with a 16 mm diameter pin. The width of…

A: Given: Diameter of pin = 16 mm Width of rectangular bar = 60 mm Bar thickness = 25 mm Maximum…

Q: In the following structure, consider the following data: The connection at D is double and has a…

Q: toonges as aasm 12 mm thick plate is conected to two 8 mm thick plates, on either side through a 16…

Q: A tie-down on the deck of a sailboat consists of a bent bar bolted at both ends, as shown in the…

A: Given:

Q: A threaded steel rod (Es = 210 GPa, dr = 12 mm, as = 12 x 10-6/°C) is held stress free between rigid…

A: Given, Es=210 GPadr=12 mm4αs=12×10-6/°Cdp=15 mτ=45 MPaσ=70MPa

Q: 5) Match the beam bending stress profile for design to the correct cross section shown below: "包。…

A: Given that:

Q: The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part…

Q: Explam how the total stess at a distance z be determined from the figure below Com ground surface…

A: For multi layered soil Total stress is given by :σt=∑ γtγ=unit weightst=thickness of each layer

Q: The stiffness coefficient 'k11' for the beam shown below is El 1 Internal Hinge - 2 m 3 m

Q: The stress field in a loaded aluminum plate was determined as [-2x² + 3y² 3x + y+ 5] O = F[3x + y+5…

Q: The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gpr = 39 GPa). The portion CD of…

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN,…

A: P=8kN

Q: A beam having the cross section shown is subjected to a couple Mo acting in a vertical plane.…

A: Given, Iy = Iz = b436 Iyz = b472 σ = 103 MPa

Q: When the normal stresses are at their maximum or minimum values, the shear stresses are zero. We can…

A: 1- Yes when normal stresses are maximum or minimum, then at that element shear stress is zero. 2-…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

100%

Problem 01.054-Analysis of an inverted T-frame
In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearin
stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is
desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes.
Front view.
160 mm
D
B
18 mm
B
Top view
120 mm
largest load P that can be applied at A is
99252
2.328 KN.
ED
6 mm
22B
Side view

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compound axial member ABC has a uniform diameter of d = 1.50 in. Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 80 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 112 in. When axial force P is applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 1700 pin./in. in longitudinal direction. What is the total elongation of member ABC? L2 (1) d Aluminum В (2) Сopper
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 2- 4 testb 2 4
Part 2,3,4
A 200 MPa shear stress is applied on along CD. Calculate diagonal strain along AC. Given modulus of elasticity is 120 GPa and Poisson's ratio is 0.2. 200 MPa A B Diagonal strain will be in the form of k x 10-3 Find 'k'
the assembly consists of three disk a b and c that are used to support the load of 140kn if d1=25mm and d2=70mm and d3=30mm determine the compressive stress in disk A, DISK B AND DISK C
N = 7
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. %3D Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. %3D When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 1500 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L1 P L2 A Aluminum В d Copper c'P Answer: AL = in. %3D
904. To avoid interference, a link in a certain machine is de- signed so that its cross-sectional area is reduced one-half at section A-E, as shown in Fig. P-904. Compute the maximum tensile stress developed across section A-B if (a) the cross section of the link is 160 mm square and (b) the cross section is a circle 160 mm in diameter. Ans. (a) 75.0 MPa; (b) 85.3 MPa 80 mm P = 240 kN 80 mm B Figure P-904.
Torialai Stan Problem 1-- Short link BD consists of a single steel bar 40 mm wide and 12 mm thick. Knowing that = Call 100 Mpa, determine: a) The maximum value of the normal stress in the link BD b) The required pin diameter at support D. 20kN 100 150 mm 300 mm D 30
the trolley of a small hoist is supported on a horizontal beam as shown. the maximum mass to be lifted is 6000kg the tie back is a round rod 33 mm in diameter the tensile stress in the is not to exceed 170 MPa the maximum elongation allowed for the tie back is 2.5 mm. determine the maximum dimemnsion L permitted
2. (3 points) When loading is applied at a point on a body, the stress distributions at different cross sections are different. However, the stress distribution becomes uniform at locations far from the applied load. This is due to which principle? Name the principle. P Load distorts lines located near load P P C C Lines located away from the load and support remain straight P O avg A section a-a section b-b section c-c -Load distorts lines located near support Your answer