A threaded steel rod (Es = 210 GPa, dr = 12 mm, as = 12 x 10-6/°C) is held stress free between rigid walls by a clevis and pin (dp = 15 mm) assembly at each end. If the allowable shear stress in the pin is 45 MPa and the allowable normal stress in the rod is 70 MPa, what will be the maximum permissible temperature drop AT? %3D pin, dp ΔΤ rod, d, Clevis

A threaded steel rod (Es = 210 GPa, dr = 12 mm, as = 12 x 10-6/°C) is held stress free between rigid walls by a clevis and pin (dp = 15 mm) assembly at each end. If the allowable shear stress in the pin is 45 MPa and the allowable normal stress in the rod is 70 MPa, what will be the maximum permissible temperature drop AT? %3D pin, dp ΔΤ rod, d, Clevis

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q5) The wooden block shown in Figure (4) will fail if the shear stress acting along the grain is (3.85 MPa). If the normal stress (d, = 2.8 MPa), determine the necessary compressive stress (a) that will cause failure. Figure (4)
Problem #2 (5 points): Fig. 2 shows aluminum hollow rods (outer diameter is 2 in. and inner diameter is 1.5 in.) that are fixed to rigid walls. The gap between the rods is 0.005 in when the temperature is 60°E. If the temperature is 200°F, what is the stress in each rod? aai = 13 x 10/F, Eai = 12 x 10 ksi %3D 0.005 in. .8 in. Fig. 2 Page | 1
Please no hand writing solution for other wise down vote
Detailed Solution please
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) op1 = 2320 psi, op2 = -1590 psi, op3 = 0 (b) op1 = 47 MPa, Op2 = 27 MPa, Op3 = 0 %3D Answer: (a) Tabs max psi MPa (b) Tabs max
During the tension test, the wooden specimen is subjected to an average normal stress of 2 ksi. Determine the axial force P applied to the specimen. Also, find the average shear stress developed along the section Ɵ -a of the specimen.
please box the final answer
A solid steel tube must carry a tensile load of 40KN. Determine the diameter of the tube if the stress is limited to 120 Nm/m²
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) Op1 = 2780 psi, Op2 = -2440 psi, op3 = 0 (b) op1 = 58 MPa, op2 = 35 MPa, Op3 = 0 Answer: (a) Tabs max= psi (b) Tabs max = MPa
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) Op1 = 3300 psi, Op2 = -1830 psi, Op3 = 0 (b) 0p1 = 44 MPa, Op2 = 29 MPa, Op3 = 0 Answer: (a) Tabs max psi (b) Tabs max= MPa
answer quickly
3 DECIMAL PLACES 1. what is the axial stress in the bronze rod (MPa)? first pic 2. what is the maximum tangential stress (MPa) if the internal pressure is 1.8 MPa and the wall thickness is 13mm? second pic