In the steel structure shown a 6 mm diameter pin is used at C and 10 mm diameter pin is used at B. The ultimate shearing stress is 150 MPa at all the connections. What is the largest P that can be applied? Front view 160 mm D <-15 Top view 120 PD 11111 528 Side view

In the steel structure shown a 6 mm diameter pin is used at C and 10 mm diameter pin is used at B. The ultimate shearing stress is 150 MPa at all the connections. What is the largest P that can be applied? Front view 160 mm D <-15 Top view 120 PD 11111 528 Side view

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two plates with a thickness of 35mm, width of 160mm, and length of 200mm are joined together by a pin with a diameter of 60mm. 200 mm 60 mm P 160 mm T 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250MPA and the shear strength of the pin is 100MPA. Suppose that P is 140KN, the Modulus of Elasticity is 200GP,, and the Poisson's ratio is 0.3. 2) Determine the change in length of each plate. 3) Determine the change in width of each plate. 4) Determine the change in thickness of each plate.
The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld CANNOT exceed 3 in. If the weld must transmit a total force equal to 9600 lb. Its size should be A. 1/2 in B. 3/8 in C. 5/16 in D. 1/4 in
(N) 32900
Problem 01.054-Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearin stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view. 160 mm D B 18 mm B Top view 120 mm largest load P that can be applied at A is 99252 2.328 KN. ED 6 mm 22B Side view
A steel beam is bolted to a steel girder by a connection similar to that in the figure shown below. The diameter of the bolt is 10 mm, and the thickness of each angle bar is 4 mm. For each bolt, assume that the allowable bearing stress is 224 MPa. Find the allowable load in kN on the connection. Assume the thickness of the web of the beam to be 7 mm and the thickness of the web of the girder to be 8 mm The final answer should include two decimal places
The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between the jaws. In this case; a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure. b) Show the distribution of normal stresses across the section height. (draw) c) Since the clamp material has tensile strength (apull) safety = 50MPA and compression safe stress (opress) safety = 80MPA, what is the great compressive load (P) that can be applied without damaging the a-a section? %3D %3D (Please solve in detail and according to engineering rules.) Material mechanics Sectional view a-a - 20mm T. 183mm 40mm
P 130 mm 25 mm 25 mm P P 3. Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
WELDED CONNECTIONS: THE BRACKET SHOWN IN THE FIGURE IS WELDED ON ONE SIDE OF A STEEL COLUMN WITH 800 mm OF 6 mm FILLET WELD. DETERMINE THE MAXIMUM SHEAR STRESS ON THE WELD.
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
For the beam shown in Figure (1), determine: a) The stresses in rods AB and BC. The cross-sectional area of rod AB is 155 mm2, and for BC is 200 mm?. b) The average shear stress in bolt at pin A. 1500 N S5 15 m 600 N/mt m- -3 m- Figure (1)