afe strength of a 5/16 in. fillet weld if it's actual length is 3 1/2 in. and the allowable unit stress in shear is 13,600 psi? A. 8650 lb B. 9420 lb C. 10,500 lb D. 11,800 lb

Q: Determine the shear Load that act on the fillet weld that joining two plates together if the working…

A: Length of the weld  = l = 7inThickness of the plate = t = .5inWorking stress = δ = 11300lb/in2.

Q: Two plates are held together by 3, 23 mm diameter bolts. If a 11 kN load is applied to the plates in…

A: Number of bolt = 3 Diameter of bolt (d) = 23 mm Load (P) = 11KN

Q: The following image shows a front and side view of the column connection. The bolts have a diameter…

A:

Q: W P'

A:

Q: diameter of washer = 9/8 inch = stress in the nut 18 ksi g stress 800 psi

A: d=7/8 inch  dia of root thread = 0.731 inch din = 9/8 inch tensile stress = 18ksi bearing stress  =…

Q: A 12.5-mm round structural steel rod is loaded in tension to fracture. The 200-mm gage length of…

A: ASKED: To compute the average strain for the steel rod.   Given, Gage length of the rod (L) = 200 mm…

Q: he double I-beam is fabricated by welding the three plates together as shown. Part A 50 mm 75 mm 20…

A: Shearing stress is defined as a type of stress that acts coplanar with the cross section of a…

Q: A double U-shaped butt weld is to connect two plates 200 mm (d) x 20 mm (b), as shown in the given…

A: A double U-shaped butt weld is connecting two plates of dimension,Moment =

Q: The allowable unit stress in shear on a fillet weld is 15,000 psi, and the total actual length of…

A:

Q: Figure 3 shows a truss where P = 40 kN and Q = 27 kN. The force reaction at A in the y-direction is…

A:

Q: The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of…

A: Given data: P=9600 lb Permissible shear stress, PSS=13600 psi Length of weld, L=3 in. Weld size=?

Q: A hole 12 mm diameter is to be punched through a plate 18 mm thick. If the shear strength of the…

A: Diameter of hole  d=12 mm and is punched through a plate 18 mm thick   plate thickness t= 18 mmthe…

Q: What type of joint is show What type of weld is show s the weld in shear or nor Calculate the…

A: To find:- type of joint type of weld type of stress magnitude of stress

Q: For the state of stress shown, determine two values of Øy for which the maximum shearing stress is…

A:

Q: Derive the maximum steel ratio and the recommended rteel ratio Po 004 fc' 0.85 61 fy fc' pooos= 0.85

A: Maximum steel ratio: T = C T = As fyC= 0.85 fc b a Where,  As = Area of steel fy = tensile strength…

Properties of Aluminium

Aluminum (or Aluminum) is a silvery-white in color metal. The chemical symbol of aluminum is Al and it has an atomic number (Z) of 13 in the periodic table. The aluminum name for this metal is derived from the Latin word ‘alumen’, which means bitter salt. Aluminum was discovered in the year 1825 by Hans Oersted, and later Friedrich Wöhler isolated aluminum. It is the most commonly found metal in the earth’s core, which is around 8% of the total core mass. Moreover, it is the third most commonly found element on earth after oxygen and silicon. Electron distribution of aluminum per shell is 2, 8, and 3 with a valency of 3. Atomic weight is nearly 26.9815 u.