The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld CANNOT exceed 3 in. If the weld must transmit a total force equal to 9600 lb. Its size should be A. 1/2 in B. 3/8 in C. 5/16 in D. 1/4 in

Q: Calculate the maximum shear force in the welds and the required weld size in the given figure. Where…

A: Given that :-A weld structure is given in the question with following specifications :P = 50 kNX =…

Q: 9.9 A No. 32 (metric designation) reinforcing bar for concrete has a diameter of 32 mm. The bar is…

A:

Q: For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa…

A:

Q: The screw in the illustration is subjected to a 10kN force represented by the red arrows. If the…

A: Considering normal stress:σallow=PA70mpa=20×1000Nπ4d2d=19.07mm≈20mm

Q: How many inches of 1/8-in weld are necessary to transfer a shear force of 6000 lb from one plate to…

A: The objective of the question is to find out the length of the weld required to transfer a shear…

Q: 1-66 Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be, if the…

A:

Q: Determine the shear Load that act on the fillet weld that joining two plates together if the working…

A: To find- Shear load

Q: Problem 02 Axial compression loads in the first interior column of the structure shown are: 95 kN…

A: Given:-dead load=95kNlive load=50kNwind load=75kNk=0.65To find:-remaining allowance

Q: Give the formula for the tensile and shear strength of the weld joint. Explain the various terms in…

A: Need to definethe formula for the tensile and shear strength of the weld joint

Q: A double U-shaped butt weld is to connect two plates 200 mm (d) x 20 mm (b), as shown in the given…

A: A double U-shaped butt weld is connecting two plates of dimension,Moment =

Q: The equivalent stress for welding in given bracket connections would be if t = 5mm e i.e. Effective…

A: Effective throat thickness of weld te=5 mm,Fe410 steel & shop welding case,To Find-The value of…

Q: with the same distribu pattern. y express the lets. 8 Weld (C) Now, we weld the two sections to form…

A:

Q: Determine the required weld size necessary to carry the load P.

A: Solution Dead load(PDL)=360 kN Live load(PLL)=120 kN The centroid of the area is, x=1502=75…

Q: 2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load…

A: LL = 25 kNDL = 50 kNU = 1.0Plate dimensions: 10 x 100 mmFactored load:P = 1.2 DL + 1.6 LL = (1.2x50)…

Q: The vertical force P acts on the top of the post. Please determine the distance d at which the load…

A:

Alloys

An alloy is an admixture of two or more metals or a metal and a non-metal. Since ancient times, man has been using alloys. Alloying helps to retain the properties of the parent matter, such as hardness, strength, toughness, ductility and is corrosion-resistant. Copper alloys such as brass have antimicrobial properties that help to fight against (Coronavirus disease 2019) COVID-19 and other hospital-acquired infections. Some common alloys are brass, bronze, solder steel, etc. Most alloys have a lower melting point than their constituents. This is due to the presence of a nonmetal as one of the constituents that behaves as an impurity and restricts the raise of melting point.