A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After loadP is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection atpin C before the load is applied.A240 mmB(1)O 1281 um/mO 1877 µm/mO 1141 µm/mO 1358 µm/mO 999 µm/m360 mm(2)Rigid bar900 mmC140 mm,1,500 mm

Answered: Image /qna-images/answer/d7a0caea-2fef-4010-ab4a-d350c1ff5bda.jpg

A rigid bar ABCD is supported by two bars as shown in the figure. There is P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the norm pin C before the load is applied. 240 mm B (1) O 1281 μm/m O 1877 μm/m O 1141 μm/m O 1358 μm/m 360 mm (2) Rigid bar 900 mm с 140 mm, 1,500 mm

A rigid bar ABCD is supported by two bars as shown in the figure. There is P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the norm pin C before the load is applied. 240 mm B (1) O 1281 μm/m O 1877 μm/m O 1141 μm/m O 1358 μm/m 360 mm (2) Rigid bar 900 mm с 140 mm, 1,500 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the deformation of the steel rod shown in Fig. under the given loads (E = 200 GPa). [ A =…

Q: Beams: 4a A beam of cross section as shown (dimensions in centimeters) is loaded by a positive…

Q: A thin square plate is uniformly deformed as shown in the figure. Assume a - 100 mm, b-15 mm, c-85…

A: Given Data:Assume a=100mmb=15mmc=85mmand d=115mm

Q: 2.) When an axial load is applied to the ends of the bar shown, the total elongation of the bar…

A: Given:- Total elongation of the bar between joints A and C = 0.15 in Normal strain measured in…

Q: The force applied at the handle of the rigid lever as shown in figure 1 causes the lever to rotate…

A: The lever arms rotates through an angle of Since - is small A,C,D can be approximatedCalculate the…

Q: The state of stress at a certain point in a stressed body is as shown in the figure. Normal stress…

A: We have to determine the radius of the Mohr circle

Q: The figure below shows the cross-section of a beam that carries a vertical shear force, V= 72 kN.…

Q: A cantilever beam is made by using cross-section as shown in figure. A hogging bending moment of 0.4…

Q: A 52-kip force acts on a machine part at point A as shown below. The diagram shows the internal…

A: It is required to find the bending moment at the rectangular stress element.

Q: G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods.…

Q: P2. The thin-walled cantilever beam of unsymmetrical cross-section supports shear loads at its free…

Q: A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi;…

A: Normal force is the ratio of force to area

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load
P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at
pin C before the load is applied.
A
240 mm
B
(1)
O 1281 um/m
O 1877 µm/m
O 1141 µm/m
O 1358 µm/m
O 999 µm/m
360 mm
(2)
Rigid bar
900 mm
C
140 mm,
1,500 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the normal strain in rod (2)

VIEW

Step 2: Determine the normal strain in rod (2)

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

904. To avoid interference, a link in a certain machine is de- signed so that its cross-sectional area is reduced one-half at section A-B, as shown in Fig. P-904. Compute the maximum tensile stress developed across section A-B if (a) the cross section of the link is 160 mm square and (b) the cross section is a circle 160 mm in diameter. Ans. (a) 75.0 MPa; (b) 85.3 MPa 80 mm P = 240 kN 80 mm $2 B Figure P-904.
A 5.2-m-long aluminum tube (1) is to be connected to a 2.2-m-long bronze pipe (2) at B. When put in place, however, a gap of 9 mm exists between the two members, as shown. Aluminum tube (1) has an elastic modulus of 69 GPa and a cross-sectional area of 1980 mm2. Bronze pipe (2) has an elastic modulus of 93 GPa and a cross-sectional area of 3970 mm2. If bolts are inserted in the flanges and tightened so that the gap at B is closed, determine: (a) the normal stresses ?1, ?2 produced in each of the members. (b) the displacement (change in length of material (2), up is positive) uB of flange B with respect to support A. 5.2 m 2.2 m Answers: (a) 0₁ = (b) Ug = C (1) B (2) -95.40 1.126 9 mm MPa, 0₂ = mm. -47.58 MPa
904. To avoid interference, a link in a certain machine is de- ed so that its cross-sectional area is reduced one-half at section r. as shown in Fig. P-904. Compute the maximum tensile stress developed across section 4-B if (a) the cross section of the link is 160 mm square and (b) the cross section is a circle 160 mm in diameter. Ans. (a) 75.0 MPa; (b) 85.3 MPa 80 mm P-240 kN 80 mm Flgure P-904.
4) 4 points Calculate the minimum net area for the plate shown below connected to 14 mm thick gusset plate with 22 mm bolts. Plate 12 mm thick 35mm 20mm 20mm 150 mm 20mm 20mm 35mm „Gusset 14 mm thick 35mm 30mm 30mm 40mm a. 936 mm? b. 918 mm? c. 900 mm? d. 887 mm?
Solid Mech, Question 6 b, A rod of dimension 20 mm x 20 mm is carrying an axial tensile load of 10 kN. The tensile stress developed is
400mm Find the required spacing of intermediate stiffeners if V*=1600KN 25mm • Check the adequacy of a pair of stiffeners 90mmx12mm • Check the web crushing capacity if the reaction of 1600kN is applied over a stiff bearing length of 250mm at the end of the beam (note that the spread of stress can only go in one direction) • Homework extension: Check the adequacy of an endplate stiffener 300 wide by 16mm thick 12mm Use Grade 300 Steel 1440mm
In the following structure, consider the following data:The connection at D is double and has a diameter of 50 mm. The beam BCDE has a thickness of 37.50 mm. The bar AB has a thickness of 37.50 mm and a width of 100. The connection at A is single and has a diameter of 67.50 mm.a. The normal stress in bar AB.b. The shear stress in the bolt at D.c. The shear stress in the bolt at A.d. The support stress between the beam and bolt D.
Handwritten Asap.
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Fig. P-108. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. Figure P-108 PARTNER Aluminum A=400 mm² Steel A = 500 mm² 2.5 m 2.0 m Bronze A = 200 mm² 1.5 m 2P
An aluminum tube with the hexagonal cross-section shown is 2.5 ft long and has a constant wall thickness of 0.080 in. Find (a) the largest torque that the tube can carry if the shear stress is limited to 7200 psi. Use G = 4 x 106 psí for aluminum. 11.5 in 0.075 in O 6734 lb-in O 7634 lb-in O 6374 lb-in O 7346 lb-in
A steel plate is used to connect a column and beam as shown in Fig. 3. The connection betweenthe beam and the plate is fillet welds. Given Q=150kN and Mx= -5kN-m (applied at centriod ofthe welds between the beam and the plate), determine maximum shear stress in the welds betweenthe beam and the plate.
If a force with a magnitude of P applied to point E and in turn it causes the rigid lever to rotate clockwise about the pin B through an angle of 4°, find he average normal strain in wires AH, GC and FD. The wires are 200 mm300 mm 200 mm 300 mm unstretched when the lever is in the horizontal position 200 mm