Thescrew clamp shown in the figure applies a P = 500 N pressing force to the woodenblocks between the jaws. In this case;a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shownin the figure.b) Show the distribution of normal stresses across the section height. (draw)c) Since the clamp material has tensile strength (apull) safety = 50MPA and compressionsafe stress (opress) safety = 80MPA, what is the great compressive load (P) that can beapplied without damaging the a-a section?%3D%3D(Please solve in detail and according to engineering rules.)Material mechanicsSectional view a-a- 20mmT.183mm40mm

Answered: Image /qna-images/answer/c31a96c5-84c5-43d5-903e-143af9cc3871.jpg

a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure. Mww w b) Show the distribution of normal stresses across the section height. (draw) c) Since the clamr material has tensile strength (apull) safety = 50MPA and compression safe stress (opress) safety = 80MPa, what is the great compressive load (P) that can be applied without damaging the a-a section? %3D

a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure. Mww w b) Show the distribution of normal stresses across the section height. (draw) c) Since the clamr material has tensile strength (apull) safety = 50MPA and compression safe stress (opress) safety = 80MPa, what is the great compressive load (P) that can be applied without damaging the a-a section? %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the length of tension anchorage required for the 36 mm diameter plain mild steel reinforcing bars in the canrilever of figuer below. The charactersitic material strengths are feu-30N/mm² and fy=250KN. The ultimate anchorage bond stress. Stress, fou-1.5N/mm² Anchorage length R25 bars
The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ? P steel raid steel sF I A=0-1 Mat 50°d E = 200 GPa -Aluminum L= 250 Mm A = 1600 mm ² X = 12 x10%2 Call = 200 MPa Comp Alumivun Post. E = 73 GPa A = 2400 mM 400 mM 40o mm 2 X = 23 x 10% T = 150 MP Comp Figure 2
What maximum load P can be applied without exceeding an allowable stress of 70 MPa for aluminum or 120 MPa for steel? Can a larger load P be carried if the length of the aluminum rod is changed. the length of the steel portion being kept the same? If so, determine this length
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 25 kips, w = 3.6 kips/ft, LAB = 5.6 ft, LBC = 5.6 ft, and LcD = 16.8 ft. Determine the magnitude of the maximum bending stress in the beam. LAB Answer: Omax = i B LBC C ksi W LCD D ZOQ Q 214% TOP BARI ENG 11:41 am 35 28/04/2023 8 cores
QU A composite beam is fabricated by bonding a steel bar and a brass bar and is subjected to the bending moment M = 200 N-m. Determine the maximum bending stress in the brass and steel. Given: E, =200 GPa, E, = 100 GPa Brass 20 }o | Jakrtal
Two T-shape sections are welded together to create a composite l-beam section as shown below. Determine the safely uniform load w (kN/m) that the beam can carry throughout its entire span. 270mm 30mm 20mm 160mm Welded Joint 130mm 30mm 135mm Beam Length = 4 m Consider the following stresses: fb(T) 3 125 МPа fb(C) = 130 MPa x at the welded joint = 20 MPa Find: 1. The Neutral Axis from the base 2. moment of inertia with respect to the horizontal centroidal axis 3. Q at the welded joint 4. Considering the maximum flexural stress in tension, WNAX is equal to KN/m. 5. Considering the maximum flexural stress in compression, WMAX, is equal to 6. Considering the stress at the welded joint, wMex is equal to kN/m.
Seatwork The beam shown is prestressed by using a bonded (stress relieved tendons) with a specified tensile strength of prestressing tendons strength fpu=1350 MPa, fc'=35 MPa. The area of prestressed reinforcement in tension zone Aps=1000 mm?. The specific yield strength of prestressing tendons sd, foy=1160 MPa. а. What is the value of the stress in prestressed reinforcement at nominal strength (Aps) b. What is the value of the depth of the compression block. С. What is the ultimate moment capacity of the prestressed beam. 0.85fc' 430 NA |(d-a/2) · A=1000 T=Ap.Sps 250
According to IS 800-1962 the permissible bending stress in steel slab plate is (b) 1420 kg/cm² (d) 1890 kg/cm² (a) 1500 kg/cm² (c) 2125 kg/cm²
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
What is the manufacturing tensional yield strength (lbf) of grade S135 drill pipe? a. This is a trick question because drill pipe size is not provided b. The answer can’t be calculated because the length of the pipe is not given c. The yield strength is 135000 psi and is a property of the steel d. The yield strength is 135000 psi and depends on the cross-sectional area
Please solve this question and provide solution
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.