A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the zdirection. The block is subjected to triaxial loading consisting of three uniformly forces as follows:24 KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension inthe z-direction. If u = 0.3 and E = 200 GPa, Determine the total resulting strain in the z- direction.Note: CN is the last 2 non zero digits of your cellphone number

Answered: Image /qna-images/answer/9c9e3fbe-3581-4c8e-9dd4-0b4d6808dcc0.jpg

A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: 241 KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 and E = 200 GPa, Determine the total resulting strain in the z- direction. Note: CN is the last 2 non zero digits of your cellphone number

A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: 241 KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 and E = 200 GPa, Determine the total resulting strain in the z- direction. Note: CN is the last 2 non zero digits of your cellphone number

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q.1. A For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detemine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. B. What force is required to punch a square hole (25-mm*25mm) in a plate that is 30 mm thick? The shear strength is 350 MN'm2. Punchar 25 mm 26 mm 30 mm thick
(c) A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a compressive stress of 50 N/mm² in a direction at right angles to the previous one. Find fully the stresses on a plane the normal of which makes an angle of 40 degree with the 70 N/mm² stress.
Please show complete work on a sheet of paper ,Diagram should be included.
A typical aluminum-alloy scuba diving tank is shown. The outside diameter of the tank is 200 mm and the wall thickness is 12 mm. If the air in the tank is pressurized to 14MPa, determine the maximum shear stress in the plane of the cylinder wall. 24.1 MPa 15.5 MPa 25.7 MPa 32.2 MPa 20.9 MPa
A RECTANGULAR ALUMINUM BLOCK IS 110mm LONG IN THE X DIRECTION, 70mm WIDE IN THE Y DIRECTION AND 85mm THICK IN THE Z DIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF A UNIFORMLY DISTRIBUTED FORCE OF 210 KN (COMPRESSION), 170 KN (TENSION) AND 230 KN (COMPRESSION) IN THE X, Y AND Z DIRECTIONS RESPECTIVELY. IF THE POISSON'S RATIO = 1/4 & E= 72 GPa, DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSO DETERMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THE WOULD PRODUCE THE SAME Z DEFORMATION AS THE ORIGINAL.
pre stressed conc. solution pls answer
Question 4 : Please answer part A and B!
(c) A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a compressive stress of 50 N/mm² in a direction at right angles to the previous one. Find fully the stresses on a plane the normal of which makes an angle of 40 degree with the 70 N/mm² stress.
Please just do problem 8.2
A 4.5-m-long steel rod must not stretch more than 3.2 mm and the normal stress must not exceed 180 MPa when the rod is subjected to a 10-kN axial load. Knowing that E=200 GPa, determine the required diameter of the rod. Round off to two decimal places and answer in mm
In the following beam system, the beam is subjected to uniform distributed load W = 25 lb /in. Assume a = 90-inch, b = 130-inch, C = 40 inch and d = 50 inch a) Determine the resultant force produced at the pin C for the distributed load, W b) What is the factor of safety that exists for pin C with respect to its fracture strength? assume that the pin at C fractures when the resultant force reaches a value 35000 lb.
Please show all steps