In a standard tensile test a steel rod of 22-mm diameter is sub- jected to a tension force of 75 kN. Knowing that v = 0.3 and E= 200 GPa, determine (a) the elongation of the rod in a 200-mm gage length, (b) the change in diameter of the rod. H 9:59 3/12/2

In a standard tensile test a steel rod of 22-mm diameter is sub- jected to a tension force of 75 kN. Knowing that v = 0.3 and E= 200 GPa, determine (a) the elongation of the rod in a 200-mm gage length, (b) the change in diameter of the rod. H 9:59 3/12/2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A cross-section of a beam, symmetrical relative to the vertical axis, is shown in Figure Q2. If the…

A: for Section 1: Width b= 4a and depth d = a for Section 2: Width b= a and depth d =3a for…

Q: toonges as aasm 12 mm thick plate is conected to two 8 mm thick plates, on either side through a 16…

Q: Determine the stress produced in cylindrical rod of having diameter 2 mm when Tensile load of 44 KN…

A: Introduction : In this question we are provided with value of tensile load and cross section…

Q: A threaded steel rod (Es = 210 GPa, dr = 12 mm, as = 12 x 10-6/°C) is held stress free between rigid…

A: Given, Es=210 GPadr=12 mm4αs=12×10-6/°Cdp=15 mτ=45 MPaσ=70MPa

Q: A uniform beam weighing 500 N is held in a honzontal position by three vertical wires, one attached…

A: Stress = Load / Cross secrion Assuming that the load is equally distributed in all the three wires.

Q: What is the tensile stress (in MPa) in a rod of cross section 20 mm × 30 mm, carrying an axial…

A: given- cross-section area A=20 mm×30 mmAxial tensile load P=20 kN

Q: We know that P=Q=480 N, calculate (a) the distance a for which the absolute value of the bending…

A: P= 480 N Q = 480 N

Q: The rigid bar abcd supports point loads At A and D and is being supported by two bars at B and C.…

Q: total length of column member, I = 3 m beam width, b = 6" or 150 mm (dressed) beam depth, d = 6" or…

A: Total length of column(L)=3 m Total load(P)=56.25 kN Width of column(b)=6" or 150 mm Depth of…

Q: As demonstrated, four 25mm diameter rivets with a T=75kN axial load are equally distributed. The…

A: Shear stress in rivets: The plates are connected by rivets happens to exert tensile stress on the…

Q: A wire cable was was used to suspend a 500 pound support beam. The orginal length was 12 feet. The…

A: Original length, L=12' Stretched length, L'=12.01' Therefore, change in length,x=12.01'-12'=0.01'

Q: At a point in beam, the principal stresses are 100 N/mm² and 50 N/mm². The stress in x-direction is…

A: Given - The principle stresses are, σ1 = 100 N/mm2 σ2 = 50 N/mm2 The stress in x-direction, σx = 65…

Q: An elastomeric bearing pad consisting of twosteel plates bonded to a chloroprene elastomer…

A: Solution: Given: a = 125 mm b = 240 mm t = 50 mm V = 12 kN d = 8.0 mm

Q: An l-beam of the cross section shown is subject to pure bending. The elastic perfectly plastic…

Q: The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the…

Q: if the maximum shear stress acting on rectangular beam is 50 N/mm, determine the average shear…

Q: An 1130mm? cross sectional area of 50mm long steel bar is subjected to a tensile force of 20 kN and…

A: Given data : Cross sectional area (A)=1130 mm2Force (P)=20 KNElongation (∆L)=0.0435 mmLength (L)=50…

Q: Determine the maximum thickness (t) of the specimen if it is subjected to a force P = 5 KN. The bar…

A: Consider below figure ; At A ; σ = PA 100 = 5 × 100037.5 t t = 1.333 mm --------- 1

Q: Problem-3 A solid steel sphere having modulus of elasticity of 200GPa and poission's ratio of 0.25…

A: Given- Modulus of elasticity E=200 GPa, Poisson's ratio μ=0.25 Volume reduced by 0.3%, Hydrostatic…

Q: Q2]- The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and…

Q: Using critical stress to show the shear effect is negligible in solid steel simply supported column…

A: Structural engineers get a genuine pride when a venture is done, regardless of whether it is a high…

Q: A soid, crcular ber ABC consists of two segments, as shown in the figure One segment has a diameter…

Q: Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

Q: Q. A For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A: Note:- as per our company guidelines we are supposed to answer only first part. Kindly repost other…

Q: Determine the total true longitudinal strain in the rod.

A: Given. Rod length,l= 40 mmIt is streched to make a rod length of 60 mmFinal rod length,lf=20 mmFind…

Q: to a bending moment M = Last four digits of your registration number in N-m. Analyse the curved beam…

A: To find all parts

Q: Only considering stresses that are normal to the cross-sections you're designing. Where omax is the…

Q: A steel rod of 15- mm diameter is held snugly (but without any initial stresses) between rigid walls…

Q: Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

A: Given- Thickness of plate T=12 mm, Dia of rivet=16 mm, Permissible bearing stress p=270 MPa, It is…

Q: A flat steel bar, 28 mm wide by 2 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A: To find maximum stress in bar

Q: Two steel plates each of width 150mm and thickness 10mm are connected with three 20mm diameter…

Q: Athin rectangular plate is uniformly deformed as shown. If L₁ = 0.125 in. and L₂ = 0.135 in.,…

Q: moment of inertia of the cross-section about the neutral axis (in mm4) c) What is the maximum…

A: a.) Calculate the cross-sectional area of the structural tube A=bd-b-2td-2t Substitute the value in…

Q: A one inch diameter machined steel cantilever 10 in. long is loaded on the end with a force that…

A: Note : As per Bartleby guidelines policy,I have answered only 1st 3 subparts.If you need remaining…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: A 4.5-m-long steel rod must not stretch more than 3.2 mm and the normal stress must not exceed 180…

A: Given data of steel rod Length = 5 m = 5000 mm ∆Lmax = 3.2 mm Normal stress maximum = 180 MPa…

Q: (d) Determine the maximum in-plane shear stress. 10 ksi 16 ksi

A: This question is related to Principal Stresses from Strength of Material. In this question we…

Q: A leaf spring is made of plates 50 mm wide and 8 mm thick. The spring has a span of 700 mm.…

Q: The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm. If it is fixed at A and…

Q: Determine the shear stress at the section A-A'.

A: This problem is related to Strength of material. There is a I section . In this , we need to…

Q: A flat steel bar has axial loads (forces along the centroidal axis of the bar) applied at points A,…

Question

In a standard tensile test a steel rod of 22-mm diameter is sub-
jected to a tension force of 75 kN. Knowing that v = 0.3 and E =
200 GPa, determine (a) the elongation of the rod in a 200-mm
gage length, (b) the change in diameter of the rod.
0
60
9:59
3/12/2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular copper rod having length of P inches is to be twisted by torques 6.5P lb.in until the angle of rotation between the ends of the rod is 3.0°. If the allowable shear strain in the copper is 0.0006 radians, solve for the maximum permissible diameter of the rod? (Where P is 27
Question 3 A pair of lateral load is applied to a 3 m steel beam as in Figure Q3a to bend it plastically. The beam has a solid rectangular cross-section (30mm x 50mm) as in Figure Q3b. The steel behaves in elastic-perfectly plastic behavior with Yield Stress of 200 MPa. When 50% plastic condition at critical section, determine: a. the value of load P b. the Yielded Length, Lp corresponding to condition in part (a). 1.5P P 1m 1m Figure Q3a 1m 30mm 50mm Figure Q3b
I. Problem Solving. Box your final answer. 1. Find the (a) maximum tensile and compressive bending stress in the wooden beam and (b) maximum shear stress in the shaded area of a wooden beam. 1 . 4kN 2kN 3kN 2m- A 1m 1m 2m 4m 3m 8m 5m 1m
with FBD please Complete solution thank you
A solid steel tube must carry a tensile load of 40KN. Determine the diameter of the tube if the stress is limited to 120 Nm/m²
1) A brass pipe with a 0.5inch inside diameter and 1/16 inch wall is twisted using a 14inch long pipe wrench. If a load of 74 lbs is applied perpendicularly to the end of the wrench. If the E of brass is 14.6x10^6 psi, what is the max torsion stress in the pipe? • Find the outside diameter of the pipe using the ID and given wall thickness. • Find the polar moment of inertia of the cross-section of the pipe. • Find the torque being applied to the pipe, via the wrench. • Use the torsional stress equation to find the requested stress. Compare your answer: Max Torsional Stress 36.61 ksi
It is required to deisgn a close coiled helical spring which shall deflect10 mm under an axial load of 100 N at a shear stresss of 90 N/mm². Modulus of rigidity is 8 x 104 MPa. The mean diameter of the coils is 10 times diameter of the wire. Find the diameter and length of the wire necessary to form the spring.
A steel I-beam has a web that is 17inches tall and 0.19inches thick. If the max shear in the beam is 6kips, what is the approximate max shear stress in the beam in psi? Type your answer...
Determine bending stress formula for the I beam
O A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150 mm when subjected to an axial load of 10 KN. The same specimen undergoes a twist of 0.5° an a length of 150 mm over a twisting moment of 10 N-m. Using the above data, determine the elastic constants E,µ,G and K.
A steel latch is 6 mm thick. A force F of 3000 N is uniformly distributed as shown below. Do not consider the stress concentration! a) Determine the principal stresses at Scction B-B?. b) Determine the principal stresses at point A? 3 kN Y R30 L, A 125 09
Higdon