Determine stress in segment AB AluminumCopperE = 18(10) ksiSteelE = 10(10) ksiE = 29(103) ksi%3D%3DAAB = 0.09 inABC = 0.12 in?ACD = 0.06 in²3.50 kip1.75 kip2.00 kip1.50 kipADBL3.50 kip1.75 kip-18 in-12 in.-16 in:

Answered: Image /qna-images/answer/a109a4bc-11be-4b7e-bf87-2c1de91a718d.jpg

Aluminum Copper E = 18(10³) ksi Steel E = 10(10) ksi E = 29(10³) ksi %3D %3D %3D AAB= 0.09 in? ABC = 0.12 in? ACD = 0.06 in? %3D 3.50 kip 1.75 kip 2.00 kip 1.50 kip D 1.75 kip A BL 5.50 kip -18 in: -12 in.- -16 in:

Aluminum Copper E = 18(10³) ksi Steel E = 10(10) ksi E = 29(10³) ksi %3D %3D %3D AAB= 0.09 in? ABC = 0.12 in? ACD = 0.06 in? %3D 3.50 kip 1.75 kip 2.00 kip 1.50 kip D 1.75 kip A BL 5.50 kip -18 in: -12 in.- -16 in:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: steel has a modulus of elasticity of 200GPa and a Poisson’s of 0.4. Compute the shear modulus of…

Q: Describe about the deviator stress.

A: - Deviator stress is also know as Principal stress difference, Shear stress, Back pressure stage -…

Q: P4: Two wooden boards are joined by cutting and gluing them together along the plane shown in the…

A: (a) If α=20° then, θ=90°-20°=70° The normal stress is calculated as,…

Q: 20MPа 1. a 30MPа I- 40 MPa A 30° Şekil 2 a

A: Major stress = δx = 40MPaMinor stress = δy = -20MPaShear stress =ζxy = 30MPa Formula used -…

Q: 4. Find the lightest S-shape for the beam shown if the working stress in bending is 175 MPa. What is…

A: The given figure of beam is shown below:

Q: The piece of plastic is originally rectangular. Calculate the shear strain Yxy at corners A and B if…

A: For small angles.

Q: 400 mn 300 mm 300 mm: A. 200 mm -- 100 mm 400 mm B Determine the tension forces and any other forces…

Q: Suppose that in addition to the 2 at point D, a 2.20-kN downward Figure 1)

Q: 18,000 lbs K₁ 3) This steel bar is 3" x 3" by 30" long. It has a 1" diameter hole centered in the…

Q: Bending stress is directly proportional to the width of a section. True False

A: Bending Stress = M y / I Bending stress is directly proportional to bending moment. It is directly…

Q: Q.3) The original and deformed geometries of a Plastic block subjected to axial and shear stresses…

Q: In (Figure 1), u 4 kN/m and wp7 kN/m. Replace the distributed loading by an equivalent resultant…

Q: HW A rigid Sslab weighing boo Ku is Placed uPon two bronzevads and one Steel Vocd Cach of bo00 mm²…

A: Given data, Weight = 600 kN Area of bronze rod Ab = 6000 mm2 Coefficient of expansion for steel αs =…

Q: A P Front view ---160 mm What is the stress in bar BD if P = 4 kips? B D 12

A: Given: P=4kips

Q: due to buckling must be considered. If E = 240GN/m? and L/r = 90 determine the boundary condition…

Q: 3. Sample of steel bar has 12 mm diameter after performing tension test the failure load was 57 KN,…

A: Tensile strength: Tensile strength of the steel bar is defined as the maximum tension applied on the…

Q: Refer to the photo provided and please make sure your handwriting is readable. L1 = 2.02 m L2 = 1.21…

Q: The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point…

Q: Answer fast and explain the answer

Q: if the maximum shear stress acting on rectangular beam is 50 N/mm, determine the average shear…

Q: X= 482 show complete solutions and FBD

Q: Determine: 1. The traction acting on a plane with unit normal vector…

Q: 3. A rectangular steel block is subjected to triaxial loading as shown. If v = 0.3 and E = 200 Gpa,…

A: Solution Givan Data ν=0.3E= 200 GPa

Q: Problem-3 A solid steel sphere having modulus of elasticity of 200GPa and poission's ratio of 0.25…

A: Given- Modulus of elasticity E=200 GPa, Poisson's ratio μ=0.25 Volume reduced by 0.3%, Hydrostatic…

Q: normal stress = o = omax = For 8kN maximum stress is, 8×0.2 1 -×0.8×0.4² 12 MxCx Ix omax = AM = MyCx…

Q: The beam is subjected to a shear of V = 13.5 kN. Set w = 125 mm. (Figure 1) Part A Determine the…

A: Given: The shear force in the beam is 13.5 kN. Consider the figure.

Q: efine the terms shear stress and shear strain, illustrating your answer by means of a simple sketch.…

A: Given data: Shear load 30 kN Shear stress in brass⩽50 MPa Shear stress in steel⩽100 MPa

Q: Determine the proportional shear stress for a material that has a modulus of rigidity of 30 GPa and…

A: Given data : Shear strain=0.0001Modulus of rigidity (G)=30 GPa

Q: The thickness of the plate is t and the diameter of the pin is d. What is the correct area formula…

A: Given Data: A plate of thickness=t Diameter of pin=d Load applied=p It is asked to find contact…

Q: Determine the load in each member if F = 150 lb Include FBD in your solution 12 5 A 50° 20° F B

A: Free body diagram θ = tan-1 125θ = 67.38o ∑Fy = 0⇒-150 cos 20° + FAB cos 67.38° + FAC cos 50° =0…

Q: Calculate the nominal flexural strength of the following section: 140(mm) A, =1000(mm²) 400(mm) As =…

Q: Q1\ Choose the correct item (a or b or c) for each of the following statements. a b 1- Shear failure…

Q: SAMPLE PROBLEM 2: Assume that AE are equal for each rod Regd: Internal forces for member AB, CD, EF…

Q: The beam SNOV Figure Q.Z 200 GPa; /= 1120 × 106 mm4]. If w= 66 kN/m and P= 128 kN, determine: X P…

A: The beam shown in Figure Q.2 consists of a W610 × 140 structural steel wide-flange shape [E = 200…

Q: For the beam loading and geometry shown, determine the following: a. Cracking moment; f = 21 MPa b.…

A: Answer (a) Calculation of cracking Moment We know that cracking Moment is given by Mcr = fr*Iyt fr…

Q: determine the minimum force P required to punch the slot. Punch O 575 kN O 675 kN O 724 KN Slug…

Question

Determine stress in segment AB

Aluminum
Copper
E = 18(10) ksi
Steel
E = 10(10) ksi
E = 29(103) ksi
%3D
%3D
AAB = 0.09 in
ABC = 0.12 in?
ACD = 0.06 in²
3.50 kip
1.75 kip
2.00 kip
1.50 kip
A
D
BL
3.50 kip
1.75 kip
-18 in-
12 in.
-16 in:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

11.18 A long, flat steel bar 4 in. wide and 3 in. thick is reduced in width to 3 in. There are circular fillets of in. radius on each side. If the bar is subjected to an axial tensile load of 12,000 lb, calculate (a) the average tensile stress in the wide portion of the bar some distance from the change in section. (b) the average tensile stress in the narrow part of the bar. (c) the maximum tensile stress adjacent to the circular wild fillet. 11 10 A long flat steel bar 5 in wide and in thick has a circu 162111 3 H ar 11.28 A P (a (E
Part1,5,6 please
DETERMINE THE STABILITY, DETERMINANCY AND DEGREE OF INDETERMINANCY.
Solve 3,4
(c). A bar of length_1000 mm and diameter 30 mm is centrally bored for 400 mm, the bore diameter being 10 mm as shown below, Under a load of 30 kN, if the extension of the bar is 0.222 mm, what is the modulus of elasticity of the bar?
(5) This simply-supported beam has been subjected to an applied moment at midspan. The M(x) equations have been supplied for you. You are to write the v(x) equations for 0
The thin uniform plate shown has a mass of 100kg and is subjected to a force and couple momentalong its edges. If it is supported in the horizontalplane by a roller at A, a ball-and-socket joint at B,and a cord at C, determine the components ofreaction at these supports to maintain equilibrium. Please provide all written work and show FBD. Thank you!
Determine the stress of each section as per the following figure (note : urgently with the full calculation)
Solve 5,6
I need bothparts handwritten if u can't do then skip I need both I need both I needed both I need both I have 3 account I'll upvotes but skip if u can't do both
When the triangular section of a beam as shown below becomes a plastic hinge, the compressive force acting on the section (with i, denoting the yield stress) becomes Job 下から T
Kindly write legibly. Thank you