Q4: For the figure below, determine the principal stresses and show them on a sketch of a properly oriented element. Also, find the maximum shear stresses and show them on a sketch of a properly oriented element. (Consider only the in-plane stresses.) -30MPA 90 MPa 34MPa

Q: 2. A finite element analysis of a bearing housing indicates that at a point p, the material is…

A: Principle stresses are the those stresses that are to the normal with zero plane. The value of…

Q: The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part…

A:

Q: Determine the maximum force P that can be applied to the specimen. The bar is made from steel and…

A: w=150 mmh=50 mmr=20 mmt=6 mmwh=15050=3rh=2050=0.4From graph, K=1.51σavg=σallK        =1501.51…

Q: A rigid bar AB is pinned at end A and issupported by a wire CD and loaded by a force P atend B (see…

A: Given:- E = 210 GPa σY =820 MPa L =1.0 m diameter is d =3 mm To find:- (a) Assuming n = 0.2,…

Q: 2) Find... a) The principal planes b) The principal stresses c) The stress components exerted on the…

A: Givenσx=100Mpaσy=60Mpaτxy=-48MpaRadius of the circleR=(σx-σy2)2+τxy2R=(100-602)2+-482R=52…

Q: a) The principal planes b) The principal stresses c) The stress components exerted on the element…

A: Question is based on the element subjected to axial, compression and shear stress .  Magnitude of…

Q: Obtain the maximum bending moment Mx that the cross section given below can safely carry. The…

A: Sigma=100MPa

Q: Three round bars welded together axially loaded as shown. Find the normal are stress in each bar if…

A: Stress is defined as the force acting per unit area of a bar. The stress in a bar is directly…

Q: d. the normal stress in region BC. Is the material within its linear-elastic region? Yes / No A…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: Required information Consider the given state of stress. 416 ksi 10 ksi ormino the normal and…

A: The given data is: σx=0 ksiσy=16 ksiζxy=10 ksiθ=15°2θ=30°

Q: Problem 2 4 1 2 in 3 2 3 in 100 psi (a) Compute the unknown nodal displacements. (b) Compute the…

A: A beam element under axial load. The following information is given:Thickness (t) = 0.5 inE = psi…

Q: A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45…

A:

Q: Ultimate strength is the highest ordinate in the tress-strain diagram.

A: Power can be defined as energy divided by time. The unit of power is watt. Power and time are…

Q: For the element with stresses as shown below, find: . The magnitudes and directions of major and…

A: To determine-

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

A:

Q: If the beam is subjected to an internal moment of M = 30 kN.m, determine the maximum bending stress…

A: Given : M = 20 kN-m This is a problem of Solid mechanics where we have to find the max. bending…

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.