Explanation Given information: The value of upper streamline function is 4.35 m 2 / s , the average velocity is 11.5 m / s and the final value of stream function is 2.03 m 2 / s . Write the expression for the total volume flow rate per unit width through upper branch. V ˙ W = ψ 1 − ψ 3 ............ (I) Here, the upper line stream function is ψ 1 , the stream function of third pipe is ψ 3 , the total volume flow rate per unit width through upper branch is V ˙ W . Write the expression for the cross- sectional area of the duct. A = W h ............ (II) Here, the cross- sectional area of the duct is A , the width of the duct is W and the height of the duct is h . Write the expression for the volume flow rate. V ˙ = V A ............ (III) Here, the average velocity is V and the volume flow rate is V ˙ . Calculation: Substitute W h for A in Equation (IV). V ˙ = V W h V ˙ W = V h ............. (V) Substitute 4.35 m 2 / s for ψ 1 and 2

4th Edition

ISBN: 2810022150991

Author: CENGEL

Publisher: MCG

See similar textbooks

Videos

Question

Chapter 9, Problem 62P

To determine

The height of the duct in cm.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9, Problem 61P

Chapter 9, Problem 63EP

Students have asked these similar questions

In deriving the vorticity equation, we have used the identity divergence x (divergence P) = 0 Show that this identity is valid for any scalar lamda by checking it in Cartesian and cylindrical coordinates.

Hello sir Muttalibi is a step solution in detailing mathematics the same as an existing step solution EXAMPLE 6-1 Momentum-Flux Correction Factor for Laminar Pipe Flow CV Vavg Consider laminar flow through a very long straight section of round pipe. It is shown in Chap. 8 that the velocity profile through a cross-sectional area of the pipe is parabolic (Fig. 6-15), with the axial velocity component given by r4 V R V = 2V 1 avg R2 (1) where R is the radius of the inner wall of the pipe and Vavg is the average velocity. Calculate the momentum-flux correction factor through a cross sec- tion of the pipe for the case in which the pipe flow represents an outlet of the control volume, as sketched in Fig. 6-15. Assumptions 1 The flow is incompressible and steady. 2 The control volume slices through the pipe normal to the pipe axis, as sketched in Fig. 6-15. Analysis We substitute the given velocity profile for V in Eq. 6-24 and inte- grate, noting that dA, = 2ar dr, FIGURE 6–15 %3D Velocity…

he velocity at apoint in aflued for one-dimensional Plow wmay be aiven in The Eutkerian coordinater by U=Ax+ Bt, Show That X Coordinates Canbe obtained from The Eulerian system. The intial position by Xo and The intial time to zo man be assumeal · 1. x = foxo, yo) in The Lagrange of The fluid parficle is designated

Chapter 9 Solutions

FLUID MECHANICS FUNDAMENTALS+APPS

Ch. 9 - Explain the fundamental differences between a flow...Ch. 9 - What does it mean when we say that two more...Ch. 9 - The divergence theorem is v.cdv=A c . n dA Ch. 9 - Prob. 4CP Ch. 9 - Prob. 5CP Ch. 9 - Prob. 6CP Ch. 9 - Prob. 7P Ch. 9 - Prob. 8P Ch. 9 - Let vector G=2xzi12x2jz2kk . Calculate the...Ch. 9 - Prob. 10P

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The height of the duct in cm .

Solution Summary: The author explains the value of the upper streamline function, the average velocity, and the final value for the stream function.

Videos

The height of the duct in cm.

Want to see the full answer?

Chapter 9 Solutions