Fluid Mechanics Fundamentals And Applications
3rd Edition
ISBN: 9780073380322
Author: Yunus Cengel, John Cimbala
Publisher: MCGRAW-HILL HIGHER EDUCATION
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 52P
While traveling on a dirt road, the bottom of a car hits a sharp rock and a small hole develops at the bottom of its gas tank. If the height of the gasoline in the tank is 30 cm. determine the initial velocity of the gasoline at the hole. Discuss how the velocity will change with time and how the flow will be affected if the lid of the tank is closed tightly.
Answer. 2.43 m/s
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
plzzzz help meeee
In a refinery, fuel ethanol is flowing in a pipe at a velocity of 1.2 m/s at 2 atm. The refinery needs the ethanol to be at a pressure of 1 atm on a lower level. If the diameter of the pipe at section 1 and 2 are 40cm and 10cm respectively, how far must the pipe drop in height in order to achieve this pressure?
While traveling on a dirt road, the bottom of a car hits a sharp rock and a small hole develops at the bottom of its gas tank. If the height of the gasoline in the tank is 30 cm, determine the initial velocity of the gasoline at the hole. Discuss how the velocity will change with time and how the flow will be affected if the lid of the tank is closed tightly.
Chapter 5 Solutions
Fluid Mechanics Fundamentals And Applications
Ch. 5 - Name four physical quantities that are conserved...Ch. 5 - Define mass and volume flow rates. How are they...Ch. 5 - Does the amount of mass entering a control volume...Ch. 5 - When is the flow through a control volume steady?Ch. 5 - Consider a device with one inlet and one outlet....Ch. 5 - In climates with low night-time temperatures, an...Ch. 5 - A garden hose attached with a nozzle is used to...Ch. 5 - Air whose density is 0.082 Ibm/ft3 enters the duct...Ch. 5 - A 0.7$-m3 rigid tank initially contains air whose...Ch. 5 - Consider the flow of an incompressible Newtonian...
Ch. 5 - Consider a fully filled tank of semi-circular...Ch. 5 - Prob. 12PCh. 5 - Prob. 13PCh. 5 - The minimum fresh air requirement of a residential...Ch. 5 - Air enters a nozzle steadily at 2.21 kg/m3 and 20...Ch. 5 - Air at 40°C flow steadily through the pipe shown...Ch. 5 - A hair dryer is basically a duct of constant...Ch. 5 - Define turbine efficiency, generator efficiency,...Ch. 5 - What is mechanical efficiency? What does a...Ch. 5 - How is the combined pump-motor efficiency of a...Ch. 5 - What is mechanical energy? How does it differ from...Ch. 5 - Prob. 22PCh. 5 - A differential thermocouple with sensors at the...Ch. 5 - Electric power is to be generated by installing a...Ch. 5 - Consider a river flowing toward a lake at an...Ch. 5 - Water is pumped from a lake to a storage tank 18 m...Ch. 5 - Prob. 28CPCh. 5 - Express the Bernoulli equation in three different...Ch. 5 - What are the three major assumptions used in the...Ch. 5 - Define static, dynamic, and hydrostatic pressure....Ch. 5 - What is streamwise acceleration? How does it...Ch. 5 - What is stagnation pressure? Explain how it can be...Ch. 5 - Prob. 34CPCh. 5 - How is the location of the hydraulic grade line...Ch. 5 - Prob. 36CPCh. 5 - What is the hydraulic grade line? How does it...Ch. 5 - A glass manometer with oil as the working fluid is...Ch. 5 - The velocity of a fluid flowing in a pipe is to be...Ch. 5 - The water level of a tank on a building roof is 20...Ch. 5 - Prob. 41CPCh. 5 - In a hydroelectric power plant, water enters the...Ch. 5 - A Pitot-static probe is used to measure the speed...Ch. 5 - The air velocity in the duct of a heating system...Ch. 5 - Prob. 45EPCh. 5 - A piezometer and a Pitot tube are tapped into a...Ch. 5 - The diameter of a cylindrical water tank is D0and...Ch. 5 - A siphon pumps water from a large reservoir to a...Ch. 5 - Prob. 49PCh. 5 - Water flows through a horizontal pipe at a rate of...Ch. 5 - An airplane is flying at an altitude of 10.500 m....Ch. 5 - While traveling on a dirt road, the bottom of a...Ch. 5 - The water in an 8-rn-diameter, 3-rn-high...Ch. 5 - Reconsider Prob. 5-49. Determine how long it will...Ch. 5 - Air at 105 kPa and 37°C flows upward through a...Ch. 5 - A handheld bicycle pump can be used as an atomizer...Ch. 5 - Water at 20°C is siphoned from a reservoir as...Ch. 5 - The water pressure in the mains of a city at a...Ch. 5 - A pressurized tank of water has a 10-cm-diameter...Ch. 5 - Air is flowing through a venturi meter whose...Ch. 5 - The water level in a tank is 15 m above the...Ch. 5 - A Pilot-static probe connected to a water...Ch. 5 - The air velocity in a duct is measured by a...Ch. 5 - In cold climates, water pipes may freeze and burst...Ch. 5 - A well-fitting piston with 4 small holes in a...Ch. 5 - A fluid of density and viscosity flows through a...Ch. 5 - What is useful pump head? How is it related to the...Ch. 5 - Consider the steady adiabatic flow of an...Ch. 5 - What is irreversible head loss? How is it related...Ch. 5 - Consider the steady adiabatic flow of an...Ch. 5 - What is the kinetic energy correction factor? Is...Ch. 5 - The water level in a tank is 20 m above the...Ch. 5 - A person is filling a knee-high bucket with water...Ch. 5 - A 3-rn-high tank filled with water has a discharge...Ch. 5 - In a hydroelectric power plant, water flows from...Ch. 5 - Reconsider Prob. 5-78E. Determine the flow rate of...Ch. 5 - An oil pump is drawing 25 kW of electric power...Ch. 5 - Tater is being pumped from a large lake to a...Ch. 5 - A 15-hp (shaft) pump is used to raise water to a...Ch. 5 - Water flows at a rate of 0.035 m3/s in a...Ch. 5 - The water level in a tank is 20 m above the...Ch. 5 - A hydraulic turbine has 50 m of head available at...Ch. 5 - A fan is to be selected to ventilate a bathroom...Ch. 5 - Water flows at a rate of 20 L/s through a...Ch. 5 - The water level in a tank is 34 ft above the...Ch. 5 - A large tank is initially filled with water 5 m...Ch. 5 - Water enters a hydraulic turbine through a...Ch. 5 - The velocity profile for turbulent flow in a...Ch. 5 - Water is pumped from a lower reservoir to a higher...Ch. 5 - Water in a partially filled large tank is to be...Ch. 5 - Underground water is to be pumped by a 78 percent...Ch. 5 - Reconsider Prob. 5-88. Determine the flow rate of...Ch. 5 - A 78-percent efficient 12-hp pump is pumping water...Ch. 5 - The demand for electric power is usually much...Ch. 5 - When a system is subjected to a linear rigid body...Ch. 5 - A fireboat is to fight fires at coastal areas by...Ch. 5 - The velocity of a liquid flowing in a circular...Ch. 5 - Air at 250 kgrn3 enters a nozzle that has an...Ch. 5 - The water level in a tank is 70 ft above the...Ch. 5 - A pressurized 2-rn-diameter tank of water has a...Ch. 5 - Air flows through a pipe at a rate of 120 L/s. The...Ch. 5 - A very large tank contains air at 102 kPa at a...Ch. 5 - Water is flowing through a Venturi meter whose...Ch. 5 - Water flows at a rate of 0.011 m3/s in a...Ch. 5 - The air in a 6-m × 5-m × 4-m hospital room is to...Ch. 5 - Underground water is being pumped into a pool...Ch. 5 - A 3-rn-high large tank is initially filled with...Ch. 5 - Reconsider Prob. 5-105. In order to dram the tank...Ch. 5 - A D0=8 -m-diameter tank is initially filled with...Ch. 5 - In some applications, elbow-type flow meters like...Ch. 5 - The cylindrical water tank with a valve at the...Ch. 5 - A rigid tank of volume 1.5 m3 initially contains...Ch. 5 - A wind tunnel draws atmospheric air at 20°C and...Ch. 5 - Water flows in a 5-cm-diameter pipe at a velocity...Ch. 5 - Air at 100 kPa and 20°C flows in a 12-cm-diameter...Ch. 5 - A water tank initially contains 140 L of water....Ch. 5 - Water enters a 4-cm-diameter pipe at a velocity of...Ch. 5 - The pressure of water is increased from 100 kPa to...Ch. 5 - A 75-m-high water body that is open to the...Ch. 5 - A pump is used to increase the pressure of water...Ch. 5 - A hydraulic turbine is used to generate power by...Ch. 5 - The motor of a pump consumes 1.05 hp of...Ch. 5 - The efficiency of a hydraulic turbine-generator...Ch. 5 - Which parameter is not related in the Bernoulli...Ch. 5 - Consider incompressible, frictionless flow of a...Ch. 5 - Consider incompressible, frictionless flow of...Ch. 5 - Consider water flow in a piping network. The...Ch. 5 - The static and stagnation pressures of a fluid in...Ch. 5 - The static and stagnation pressures of a fluid in...Ch. 5 - The difference between the heights of energy grade...Ch. 5 - Water at 120 kPa (gage) is flowing in a horizontal...Ch. 5 - Water is withdrawn a the bottom of a large tank...Ch. 5 - Water at 80 kPa (gage) enters a horizontal pipe at...Ch. 5 - Seawater is to be pumped into a large tank at a...Ch. 5 - Water enters a pump at 350 kPa at a rate of 1...Ch. 5 - An adiabatic pump is used to increase the pressure...Ch. 5 - The shaft power from a 90 percent-efficient...Ch. 5 - Using a 1are bucket whose volume is known and...Ch. 5 - Your company is setting up an experiment that...Ch. 5 - Computer-aided designs, the use of better...Ch. 5 - Using a handheld bicycle pump to generate an air...Ch. 5 - Using a flexible drinking straw and a ruler,...Ch. 5 - The power generated by a wind turbine is...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The air velocity in the duct of a heating system is to be measured by a Pitot-static probe inserted into the duct parallel to flow. If the differential height between the water columns connected to the two outlets of the probe is 2.4 cm, determine the flow velocity at the center of the duct in m/s. R of air is 287 J/Kg-K.arrow_forwardDetermine the density of the liquid? The mass flow rate of the liquid is 4800 kg/s. And the velocity and area of the cross-section are 30 m/s and 20 cm2 respectively.arrow_forwardA fluid flows at 455 cubic meters per minute inside a rectangular duct, whose cross-section has a length of 150 cm and width of 85 cm. Determine the average velocity of the flow in m/s.arrow_forward
- A 6cm diameter horizontal water pipe expands to a 10cm diameter pipe. The average velocity and pressure of water before the expansion section are 7 m/s and 150 kPa, respectively. Determine the pressure in the larger diameter pipe.arrow_forwardA 60 mm diameter pipe enlarges to a 90 mm diameter pipe. In the smaller pipe, the density of a steady flow gas is 150 kg/m3 and the velocity is 40 m/s, whereas in the larger pipe the velocity is 21 m/s. Determine the density of the gas in the larger pipe. Provide your answer in kg/m3.arrow_forwardThe water level in a tank is 20 m above the ground. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up. The tank is at sea level, and the water surface is open to the atmosphere. In the line leading from the tank to the nozzle is a pump, which increases the pressure of water. If the water jet rises to a height of 27 m from the ground, determine the minimum pressure rise supplied by the pump to the water line.arrow_forward
- A large, open-topped water tank is being filled from above by a 1.0-cm-diameter hose. The water in the hose has a uniform speed of 11 cm/s. Meanwhile, the tank springs a leak at the bottom. The hole has a diameter of 0.70 cm. Determine the equilibrium level heq of the water in the tank, O measured relative to the bottom, if water continues flowing into the tank at the same rate. heq 1.26 X10-3 Incorrect marrow_forwardShown on the figure below is an open tank that contains water at 10 °C. Incoming water are from the top portion of the tank at 10 kilogram per second and at the left side water inlet section of the tank. Water discharges at the lower right section of the tank at a velocity of 4 meters per second. In order to maintain the water level in the tank at a height (h) of 10 meters, the inlet mass velocity of water situated at the left side section of the tank is Blank 1 kg / m²-s. *Express your answers in whole significant figure without decimal value and without unit* Water at 10 kg/sec Water inlet h = 10 m D = 50 mm D = 70 mm Water outlet at 4 m/secarrow_forwardThe water level in a tank is 20 m above the ground. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up. The tank is at sea level, and the water surface is open to the atmosphere. In the line leading from the tank to the nozzle is a pump, which increases the pressure of water. If the water jet rises to a height of 29 m from the ground, determine the minimum pressure rise supplied by the pump to the waterline.arrow_forward
- Determine the volume flow rate and the mass flow rate of fuel from the gasoline tank to the fuel injection system of a car traveling at a constant speed on a flat road with the parameters given below: Speed of the car: 60.0 mpg gasoline consumption: 20.0 mpg The specific gravity of gasoline is given as 0.72. Express the answers in cm3/s and kg/hr.arrow_forwardA garden hose attached with a nozzle is used to fill a 20 Liters bucket. The inner diameter of the hose is d bose -8 cm, and it reduces to d nozzle water, determine average velocity (m/s) of water at the nozzle exit. = 3.24 cm at the nozzle exit. If it takes 50 seconds to fill the bucket with ,Nozzle Garden hose Bucketarrow_forwardTwo different liquids of densities p and 2p are filled in a container as shown in the diagram while the top of the container remains open to air. While carrying the container, accidentally a man has made a small hole at the bottom of the container. Determine the speed of water flowing through the hole in the given situation. 2h 2parrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license