Concept explainers
Water enters a hydraulic turbine through a 30-cm-diameter pipe at a rate of 0.6 m3/s and exits
through a 25-cm-diameter pipe. The pressure drop in the turbine is measured by a mercury manometer to be 1.2 in. For a combined turbine-generator efficiency of 83 percent determine the net electric power output. Disregard the effect of the kinetic energy correction factors.
The net electric power output.
Answer to Problem 90P
The net electric power output is
Explanation of Solution
Given information:
The initial diameter of the pipe is
Write the expression for the initial velocity of the water.
Here, the initial diameter of the pipe is
Write the expression for the final velocity of the water.
Here, the final diameter of the pipe is
Write the expression for the pressure drop.
Here, the density of the mercury and water is
Write the expression for the turbine head using the Bernoulli's equation.
Here, the head loss is
Write the expression for the net electric power output.
Here, the turbine and generator efficiency is
Calculation:
Draw the diagram for a tank fitted with orifice.
Figure-(2)
Substitute
Substitute
Substitute
Here, the gravitational constant is
Here, the density of the water is
Substitute
Substitute
Conclusion:
Thus, the net electric power output is
Want to see more full solutions like this?
Chapter 5 Solutions
Fluid Mechanics Fundamentals And Applications
- (b) A steel 'hot rolled structural hollow section' column of length 5.75 m, has the cross-section shown in Figure Q.5(b) and supports a load of 750 kN. During service, it is subjected to axial compression loading where one end of the column is effectively restrained in position and direction (fixed) and the other is effectively held in position but not in direction (pinned). i) Given that the steel has a design strength of 275 MN/m², determine the load factor for the structural member based upon the BS5950 design approach using Datasheet Q.5(b). [11] ii) Determine the axial load that can be supported by the column using the Rankine-Gordon formula, given that the yield strength of the material is 280 MN/m² and the constant *a* is 1/30000. [6] 300 600 2-300 mm wide x 5 mm thick plates. Figure Q.5(b) L=5.75m Pinned Fixedarrow_forwardHelp ارجو مساعدتي في حل هذا السؤالarrow_forwardHelp ارجو مساعدتي في حل هذا السؤالarrow_forward
- Q2: For the following figure, find the reactions of the system. The specific weight of the plate is 500 lb/ft³arrow_forwardQ1: For the following force system, find the moments with respect to axes x, y, and zarrow_forwardQ10) Body A weighs 600 lb contact with smooth surfaces at D and E. Determine the tension in the cord and the forces acting on C on member BD, also calculate the reaction at B and F. Cable 6' 3' wwwarrow_forward
- Help ارجو مساعدتي في حل هذا السؤالarrow_forwardQ3: Find the resultant of the force system.arrow_forwardQuestion 1 A three-blade propeller of a diameter of 2 m has an activity factor AF of 200 and its ratio of static thrust coefficient to static torque coefficient is 10. The propeller's integrated lift coefficient is 0.3.arrow_forward
- (L=6847 mm, q = 5331 N/mm, M = 1408549 N.mm, and El = 8.6 x 1014 N. mm²) X A ΕΙ B L Y Marrow_forwardCalculate the maximum shear stress Tmax at the selected element within the wall (Fig. Q3) if T = 26.7 KN.m, P = 23.6 MPa, t = 2.2 mm, R = 2 m. The following choices are provided in units of MPa and rounded to three decimal places. Select one: ○ 1.2681.818 O 2. 25745.455 O 3. 17163.636 O 4. 10727.273 ○ 5.5363.636arrow_forwardIf L-719.01 mm, = 7839.63 N/m³, the normal stress σ caused by self-weight at the location of the maximum normal stress in the bar can be calculated as (Please select the correct value of σ given in Pa and rounded to three decimal places.) Select one: ○ 1. 1409.193 2. 845.516 O 3. 11273.545 ○ 4.8455.159 ○ 5.4509.418 6. 2818.386 7.5636.772arrow_forward
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning