Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 2, Problem 2.66P
a.
To determine
To Verify:The given equation.
b.
To determine
Heat flux at the given boundary conditions.
c.
To determine
To Sketch:Temperature distribution and heat flux variation.
d.
To determine
Effect of thermal diffusivity on thermal response of material to a change in surface temperature.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
=
Consider a large plane wall of thickness L=0.3 m, thermal conductivity k = 2.5 W/m.K,
and surface area A = 12 m². The left side of the wall at x=0 is subjected to a net heat
flux of ɖo = 700 W/m² while the temperature at that surface is measured to be T₁ =
80°C. Assuming constant thermal conductivity and no heat generation in the wall, (a)
express the differential equation and the boundary equations for steady one-
dimensional heat conduction through the wall, (b) obtain a relation for the variation of
the temperature in the wall by solving the differential equation, and (c) evaluate the
temperature of the right surface of the wall at x=L.
Ti
до
L
X
Two large containers A and B of the same size are filled with different fluids. The fluids in containers A and B are maintained at 0° C and 100° C, respectively. A small metal bar, whose initial temperature is 100° C, is lowered into container A. After 1 minute the temperature of the bar is 90° C. After 2 minutes the bar is removed and instantly transferred to the other container. What is the temperature of the bar at the instant it is transferred?
The inner and outer radii of a hollow cylinder are 15 mm (r, ) and 25 mm (r, ), respectively. The
temperatures of the inner and outer walls are 400°C (T,) and 350°C (T,), respectively. The thermal
conductivity of the cylinder material obeys the relationship K = (400-0.05T) W/mK where T is in
degrees Celsius. Find the heat transferred from the hollow cylinder per unit length. The thermal
conductivity,
Chapter 2 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - Assume steady-state, one-dimensional conduction in...Ch. 2 - A hot water pipe with outside radius r, has a...Ch. 2 - A spherical shell with inner radius r1 and outer...Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - A composite rod consists of two different...Ch. 2 - A solid, truncated cone serves as a support for a...Ch. 2 - To determine the effect of the temperature...Ch. 2 - A young engineer is asked to design a thermal...Ch. 2 - A one-dimensional plane wall of thickness 2L=100mm...
Ch. 2 - Consider steady-state conditions for...Ch. 2 - Consider a plane wall 100 mm thick and of thermal...Ch. 2 - A cylinder of radius ro, length L, and thermal...Ch. 2 - In the two-dimensional body illustrated, the...Ch. 2 - Consider the geometry of Problem 2.14 for the case...Ch. 2 - Steady-state, one-dimensional conduction occurs in...Ch. 2 - An apparatus for measuring thermal conductivity...Ch. 2 - An engineer desires to measure the thermal...Ch. 2 - Consider a 300mm300mm window in an aircraft. For a...Ch. 2 - Consider a small but known volume of metal that...Ch. 2 - Use INT to perform the following tasks. Graph the...Ch. 2 - Calculate the thermal conductivity of air,...Ch. 2 - A method for determining the thermal conductivity...Ch. 2 - Compare and contrast the heat capacity cp of...Ch. 2 - A cylindrical rod of stainless steel is insulated...Ch. 2 - At a given instant of time, the temperature...Ch. 2 - A pan is used to boil water by placing it on a...Ch. 2 - Uniform internal heat generation at q=5107W/m3 is...Ch. 2 - Consider a one-dimensional plane wall with...Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - The temperature distribution across a wall 0.3 m...Ch. 2 - Prob. 2.33PCh. 2 - One-dimensional, steady-state conduction with...Ch. 2 - Derive the heat diffusion equation, Equation 2.26,...Ch. 2 - Derive the heat diffusion equation, Equation 2.29....Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - Prob. 2.41PCh. 2 - Prob. 2.42PCh. 2 - cylindrical system illustrated has negligible...Ch. 2 - Beginning with a differential control volume in...Ch. 2 - Prob. 2.45PCh. 2 - Prob. 2.46PCh. 2 - For a long circular tube of inner and outer radii...Ch. 2 - Passage of an electric current through a long...Ch. 2 - Two-dimensional. steady-state conduction occurs in...Ch. 2 - An electric cable of radius r1 and thermal...Ch. 2 - A spherical shell of inner and outer radii ri and...Ch. 2 - A chemically reacting mixture is stored in a...Ch. 2 - A thin electrical heater dissipating 4000W/m2 is...Ch. 2 - The one-dimensional system of mass M with constant...Ch. 2 - Consider a one-dimensional plane wall of thickness...Ch. 2 - A large plate of thickness 2L is at a uniform...Ch. 2 - The plane wall with constant properties and no...Ch. 2 - Consider the steady-state temperature...Ch. 2 - A plane wall has constant properties, no internal...Ch. 2 - A plane wall with constant properties is initially...Ch. 2 - Consider the conditions associated with Problem...Ch. 2 - Consider the steady-state temperature distribution...Ch. 2 - A spherical particle of radius r1 experiences...Ch. 2 - Prob. 2.64PCh. 2 - A plane wall of thickness L=0.1m experiences...Ch. 2 - Prob. 2.66PCh. 2 - A composite one-dimensional plane wall is of...Ch. 2 - Typically, air is heated in a hair dryer by...Ch. 2 - Prob. 2.69P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.arrow_forward2. A slab of thickness Lis initially at zero temperature. For times t> 0, the boundary surface at x 0 is subjected to a time-dependent prescribed temperature f(t) defined by: a + bt for 0Ti and the boundary at x = L is kept insulated. Using Duhamel's theorem, develop an expression for the temperature distribution in the slab for times (i) t t1.arrow_forwardQ1/A long cylindrical shell of inner radius R, = 1 cm, outer radius R₂ = 2 cm, and length L = 10 m is shown in the Figure. The inner wall of cylindrical shell is maintained at constant temperature T₁ = 10 C and outer wall is maintained at constant temperature T2 Calculate the temperature at r = 1.5 cm (Consider radial conduction only). 20 C. Assumptions: System is in steady state. Thermal conductivity, k= 22.5 W/m C, is constant. System follows Fourier's law of heat conduction. Heat loss in axial direction is negligible, T₁ - R₂ T₂arrow_forward
- A plane wall of thickness 2L = 30 mm and thermal conductivity k = 7 W/m-K experiences uniform volumetric heat generation at a rate q, while convection heat transfer occurs at both of its surfaces (x = − L, + L), each of which is exposed to a fluid of temperature T = 20°C. Under steady-state conditions, the temperature distribution in the wall is of the form T(x) = a + bx + cx² where a = 82.0°C, b = -210°C/m, c = -2x 10°C/m², and x is in meters. The origin of the x-coordinate is at the midplane of the wall. (a) What is the volumetric rate à of heat generation in the wall? (b) Determine the surface heat fluxes, q" (L)and q ( + L). (c) What are the convection coefficients for the surfaces at x = - Land x = + L? The volumetric rate of heat generation in the wall, in W/m³: q = i W/m³ The surface heat flux, in W/m²: qx ( - L) = i The surface heat flux, in W/m²: q (+ L) = i W/m² W/m² The convection coefficients for the surface at x = - L, in W/m²-K: h(- L) = i W/m².K The convection…arrow_forwardA plane wall of thickness 2L = 2*33 mm and thermal conductivity k = 7 W/m-K experiences uniform volumetric heat generation at a rate q˙, while convection heat transfer occurs at both of its surfaces (x = −L, + L), each of which is exposed to a fluid of temperature T∞ = 31°C. Under steady-state conditions, the temperature distribution in the wall is of the form T(x) = a + bx + cx2 where a = 85°C, b = −-218°C/m, c = −-23,942°C/m2, and x is in meters. The origin of the x-coordinate is at the midplane of the wall. (a) Sketch the temperature distribution and identify significant physical features. (b) What is the volumetric rate of heat generation q˙ in the wall? (c) Obtain an expression for the heat flux distribution qx″(x). Is the heat flux zero at any location? Explain any significant features of the distribution. (d) Determine the surface heat fluxes, qx″(−L) and qx″(+L). How are these fluxes related to the heat generation rate? (e) What are the convection coefficients…arrow_forwardFind the two-dimensional temperature distribution T(x,y) and midplane temperature T(B/2,W/2) under steady state condition. The density, conductivity and specific heat of the material are ρ =1200 kg/m 3, k=400 W/m.K, and cp=2500 J/kg.K, respectively. A uniform heat flux q =1000 W/m 2 is applied to the upper surface. The right and left surfaces are also kept at 0oC. Bottom surface is insulated.arrow_forward
- 6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transientlyarrow_forward4. A metal bar of length 30 cm has an initial temperature distribution at (2x + 5)°C. Suddenly the right end of the bar is contacted with an environment with constant temperature of 80°C. The left end is brought into contact with ice at 0°C. Find the temperature distribution after 10 s. Use a = 1,25 cm²/s, Ax = 5 and M = 0,5.arrow_forwardA hollow cylindrical copper conductor 1.27cm. i.d. and 5.1cm. o.d. carries a current density 5000 amp/cm². For copper K = .38 kW/m°K and electrical resistivity = 2 x 10-6 ohm cm. Find the position and magnitude of the maximum temperature and the internal and external heat removal when (a) the outside temperature is 37.8°c and no heat removal occurs on the inside and (b) the outside is at 37.6°C and the inside at 27.2°C.arrow_forward
- 3. A cylindrical pipe of negligible thickness holding a hot fluid at 140°C and having an outer diameter of 0.4 m is insulated with three layers of each 50 mm thick insulation of k₁ = 0.02: k2 = 0.06 and k3 = 0.16 W/m-K (starting from inside). The outside surface temperature is 30°C. Solve for the value of T2 (°C). • show conversions, units, and box in your final answersarrow_forward17arrow_forwardIn a conduction heat transfer process through a solid slab layer taking place under steady-state conditions, the following temperature profile is observed. T2 Ax However, conduction heat transfer in radial direction through a cylinder (again under steady-state conditions) does not yield such a straight line for the temperature profile, but the following one: T1 T2 Δη T2 T, Why? Please also provide an explanation based on conduction heat transfer equations used in both cases.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license