Whether the prescribed temperature distribution possible or not along with an explanation. The temperature distribution is not possible as the conduction and convection heat transfer is not possible. Given: The given diagram is shown in Figure 1. Figure 1 The thermal conductivity of the wall is k = 4.5 W / m ⋅ K . The steady state temperature of the wall is T ∞ = 20 ° C . The thickness of the wall is L = 0.018 m . The convection heat transfer of the wall is h = 30 W / m 2 ⋅ K . Formula Used: The expression for the energy balance equation for the steady flow is given by, q c o n d − q c o n v = 0 The expression for the conduction heat transfer per unit area is given by, q c o n d = − k ( T L − T 0 ) L Here, T L is the thickness of the wall at complete thickness of the wall and T 0 is the temperature of the wall at 0 m . The expression for the convection heat transfer per unit area is given by, q c o n v = k ( T L − T ∞ ) Calculation: The conduction heat transfer per unit area is calculated as, q c o n d = − k ( T L − T ∞ ) L = − ( 4.5 W / m ⋅ K ) ( 120 ° C − 0 ° C ) 0.18 m = − 3000 W / m 2 The convection heat transfer per unit area is calculated as, q c o n v = k ( T L − T ∞ ) = 30 W / m 2 ⋅ K ( 120 ° C − 20 ° C ) = 3000 W / m 2 The energy balance equation is calculated as, q c o n d − q c o n v = 0 − 3000 W / m 2 − 3000 W / m 2 = 0 − 6000 W / m 2 ≠ 0 The temperature distribution is not possible as the value of conduction and convection heat transfer is not equal. Conclusion: Therefore, the temperature distribution is not possible as the conduction and convection heat transfer is not possible.

Question

Want to see the full answer?

Answer 1

Question

Chapter 2, Problem 2.41P

(a)

To determine

Whether the prescribed temperature distribution possible or not along with an explanation.

The temperature distribution is not possible as the conduction and convection heat transfer is not possible.

Given:

The given diagram is shown in Figure 1.

Figure 1

The thermal conductivity of the wall is k=4.5 W/m⋅K .

The steady state temperature of the wall is T∞=20°C .

The thickness of the wall is L=0.018 m .

The convection heat transfer of the wall is h=30 W/m2⋅K .

Formula Used:

The expression for the energy balance equation for the steady flow is given by,

qcond−qconv=0

The expression for the conduction heat transfer per unit area is given by,

qcond=−k(TL−T0)L

Here, TL is the thickness of the wall at complete thickness of the wall and T0 is the temperature of the wall at 0 m .

The expression for the convection heat transfer per unit area is given by,

qconv=k(TL−T∞)

Calculation:

The conduction heat transfer per unit area is calculated as,

qcond=−k( T L − T ∞ )L=−(4.5 W/m⋅K)( 120°C−0°C)0.18 m=−3000 W/m2

The convection heat transfer per unit area is calculated as,

qconv=k(TL−T∞)=30 W/m2⋅K(120°C−20°C)=3000 W/m2

The energy balance equation is calculated as,

qcond−qconv=0−3000 W/m2−3000 W/m2=0−6000 W/m2≠0

The temperature distribution is not possible as the value of conduction and convection heat transfer is not equal.

Conclusion:

Therefore, the temperature distribution is not possible as the conduction and convection heat transfer is not possible.

(b)

To determine

The computation and the plot of the temperature at x=L , T(L) as a function of h for 10≤h≤100 W/m2⋅K along with an explanation of the results.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

!

Which formula is used to calculate the heat conduction in the AXIAL direction in a vertically located pipe segment whose inner and outer surfaces are perfectly insulated. Here r, is inner radius, r, outer radius, Tri pipe inner surface temperature, Tro pipe outer surface temperature, L is the length of the pipe, T the temperature on the lower surface, Ty the temperature on upper surface. Tu r; Tro r

You are asked to estimate the maximum human body temperature if the metabolic heat produced in your body could escape only by tissue conduction and later on the surface by convection. Simplify the human body as a cylinder of L=1.8 m in height and ro= 0.15 m in radius. Further, simplify the heat transfer process inside the human body as a 1-D situation when the temperature only depends on the radial coordinater from the centerline. The governing dT +q""=0 dr equation is written as 1 d k- r dr r = 0, dT dr =0 dT r=ro -k -=h(T-T) dr (k-0.5 W/m°C), ro is the radius of the cylinder (0.15 m), h is the convection coefficient at the skin surface (15 W/m² °C), Tair is the air temperature (30°C). q" is the average volumetric heat generation rate in the body (W/m³) and is defined as heat generated per unit volume per second. The 1-D (radial) temperature distribution can be derived as: T(r) = q"¹'r² qr qr. + 4k 2h + 4k +T , where k is thermal conductivity of tissue air (A) q" can be calculated…

Answer 2

Question

Chapter 2, Problem 2.41P

(a)

To determine

Whether the prescribed temperature distribution possible or not along with an explanation.

The temperature distribution is not possible as the conduction and convection heat transfer is not possible.

Given:

The given diagram is shown in Figure 1.

Figure 1

The thermal conductivity of the wall is k=4.5 W/m⋅K .

The steady state temperature of the wall is T∞=20°C .

The thickness of the wall is L=0.018 m .

The convection heat transfer of the wall is h=30 W/m2⋅K .

Formula Used:

The expression for the energy balance equation for the steady flow is given by,

qcond−qconv=0

The expression for the conduction heat transfer per unit area is given by,

qcond=−k(TL−T0)L

Here, TL is the thickness of the wall at complete thickness of the wall and T0 is the temperature of the wall at 0 m .

The expression for the convection heat transfer per unit area is given by,

qconv=k(TL−T∞)

Calculation:

The conduction heat transfer per unit area is calculated as,

qcond=−k( T L − T ∞ )L=−(4.5 W/m⋅K)( 120°C−0°C)0.18 m=−3000 W/m2

The convection heat transfer per unit area is calculated as,

qconv=k(TL−T∞)=30 W/m2⋅K(120°C−20°C)=3000 W/m2

The energy balance equation is calculated as,

qcond−qconv=0−3000 W/m2−3000 W/m2=0−6000 W/m2≠0

The temperature distribution is not possible as the value of conduction and convection heat transfer is not equal.

Conclusion:

Therefore, the temperature distribution is not possible as the conduction and convection heat transfer is not possible.

(b)

To determine

The computation and the plot of the temperature at x=L , T(L) as a function of h for 10≤h≤100 W/m2⋅K along with an explanation of the results.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 3

Question

Chapter 2, Problem 2.41P

(a)

To determine

Whether the prescribed temperature distribution possible or not along with an explanation.

The temperature distribution is not possible as the conduction and convection heat transfer is not possible.

Given:

The given diagram is shown in Figure 1.

Figure 1

The thermal conductivity of the wall is k=4.5 W/m⋅K .

The steady state temperature of the wall is T∞=20°C .

The thickness of the wall is L=0.018 m .

The convection heat transfer of the wall is h=30 W/m2⋅K .

Formula Used:

The expression for the energy balance equation for the steady flow is given by,

qcond−qconv=0

The expression for the conduction heat transfer per unit area is given by,

qcond=−k(TL−T0)L

Here, TL is the thickness of the wall at complete thickness of the wall and T0 is the temperature of the wall at 0 m .

The expression for the convection heat transfer per unit area is given by,

qconv=k(TL−T∞)

Calculation:

The conduction heat transfer per unit area is calculated as,

qcond=−k( T L − T ∞ )L=−(4.5 W/m⋅K)( 120°C−0°C)0.18 m=−3000 W/m2

The convection heat transfer per unit area is calculated as,

qconv=k(TL−T∞)=30 W/m2⋅K(120°C−20°C)=3000 W/m2

The energy balance equation is calculated as,

qcond−qconv=0−3000 W/m2−3000 W/m2=0−6000 W/m2≠0

The temperature distribution is not possible as the value of conduction and convection heat transfer is not equal.

Conclusion:

Therefore, the temperature distribution is not possible as the conduction and convection heat transfer is not possible.

(b)

To determine

The computation and the plot of the temperature at x=L , T(L) as a function of h for 10≤h≤100 W/m2⋅K along with an explanation of the results.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 4

Question

Chapter 2, Problem 2.41P

(a)

To determine

Whether the prescribed temperature distribution possible or not along with an explanation.

The temperature distribution is not possible as the conduction and convection heat transfer is not possible.

Given:

The given diagram is shown in Figure 1.

Figure 1

The thermal conductivity of the wall is k=4.5 W/m⋅K .

The steady state temperature of the wall is T∞=20°C .

The thickness of the wall is L=0.018 m .

The convection heat transfer of the wall is h=30 W/m2⋅K .

Formula Used:

The expression for the energy balance equation for the steady flow is given by,

qcond−qconv=0

The expression for the conduction heat transfer per unit area is given by,

qcond=−k(TL−T0)L

Here, TL is the thickness of the wall at complete thickness of the wall and T0 is the temperature of the wall at 0 m .

The expression for the convection heat transfer per unit area is given by,

qconv=k(TL−T∞)

Calculation:

The conduction heat transfer per unit area is calculated as,

qcond=−k( T L − T ∞ )L=−(4.5 W/m⋅K)( 120°C−0°C)0.18 m=−3000 W/m2

The convection heat transfer per unit area is calculated as,

qconv=k(TL−T∞)=30 W/m2⋅K(120°C−20°C)=3000 W/m2

The energy balance equation is calculated as,

qcond−qconv=0−3000 W/m2−3000 W/m2=0−6000 W/m2≠0

The temperature distribution is not possible as the value of conduction and convection heat transfer is not equal.

Conclusion:

Therefore, the temperature distribution is not possible as the conduction and convection heat transfer is not possible.

(b)

To determine

The computation and the plot of the temperature at x=L , T(L) as a function of h for 10≤h≤100 W/m2⋅K along with an explanation of the results.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 5

Chapter 2, Problem 2.41P

(a)

To determine

Whether the prescribed temperature distribution possible or not along with an explanation.

The temperature distribution is not possible as the conduction and convection heat transfer is not possible.

Given:

The given diagram is shown in Figure 1.

Figure 1

The thermal conductivity of the wall is k=4.5 W/m⋅K .

The steady state temperature of the wall is T∞=20°C .

The thickness of the wall is L=0.018 m .

The convection heat transfer of the wall is h=30 W/m2⋅K .

Formula Used:

The expression for the energy balance equation for the steady flow is given by,

qcond−qconv=0

The expression for the conduction heat transfer per unit area is given by,

qcond=−k(TL−T0)L

Here, TL is the thickness of the wall at complete thickness of the wall and T0 is the temperature of the wall at 0 m .

The expression for the convection heat transfer per unit area is given by,

qconv=k(TL−T∞)

Calculation:

The conduction heat transfer per unit area is calculated as,

qcond=−k( T L − T ∞ )L=−(4.5 W/m⋅K)( 120°C−0°C)0.18 m=−3000 W/m2

The convection heat transfer per unit area is calculated as,

qconv=k(TL−T∞)=30 W/m2⋅K(120°C−20°C)=3000 W/m2

The energy balance equation is calculated as,

qcond−qconv=0−3000 W/m2−3000 W/m2=0−6000 W/m2≠0

The temperature distribution is not possible as the value of conduction and convection heat transfer is not equal.

Conclusion:

Therefore, the temperature distribution is not possible as the conduction and convection heat transfer is not possible.

(b)

To determine

The computation and the plot of the temperature at x=L , T(L) as a function of h for 10≤h≤100 W/m2⋅K along with an explanation of the results.

Answer 6

Chapter 2, Problem 2.41P

(a)

To determine

Whether the prescribed temperature distribution possible or not along with an explanation.

The temperature distribution is not possible as the conduction and convection heat transfer is not possible.

Given:

The given diagram is shown in Figure 1.

Figure 1

The thermal conductivity of the wall is k=4.5 W/m⋅K .

The steady state temperature of the wall is T∞=20°C .

The thickness of the wall is L=0.018 m .

The convection heat transfer of the wall is h=30 W/m2⋅K .

Formula Used:

The expression for the energy balance equation for the steady flow is given by,

qcond−qconv=0

The expression for the conduction heat transfer per unit area is given by,

qcond=−k(TL−T0)L

Here, TL is the thickness of the wall at complete thickness of the wall and T0 is the temperature of the wall at 0 m .

The expression for the convection heat transfer per unit area is given by,

qconv=k(TL−T∞)

Calculation:

The conduction heat transfer per unit area is calculated as,

qcond=−k( T L − T ∞ )L=−(4.5 W/m⋅K)( 120°C−0°C)0.18 m=−3000 W/m2

The convection heat transfer per unit area is calculated as,

qconv=k(TL−T∞)=30 W/m2⋅K(120°C−20°C)=3000 W/m2

The energy balance equation is calculated as,

qcond−qconv=0−3000 W/m2−3000 W/m2=0−6000 W/m2≠0

The temperature distribution is not possible as the value of conduction and convection heat transfer is not equal.

Conclusion:

Therefore, the temperature distribution is not possible as the conduction and convection heat transfer is not possible.

Answer 7

Chapter 2, Problem 2.41P

(a)

To determine

Whether the prescribed temperature distribution possible or not along with an explanation.

The temperature distribution is not possible as the conduction and convection heat transfer is not possible.

Given:

The given diagram is shown in Figure 1.

Figure 1

The thermal conductivity of the wall is k=4.5 W/m⋅K .

The steady state temperature of the wall is T∞=20°C .

The thickness of the wall is L=0.018 m .

The convection heat transfer of the wall is h=30 W/m2⋅K .

Formula Used:

The expression for the energy balance equation for the steady flow is given by,

qcond−qconv=0

The expression for the conduction heat transfer per unit area is given by,

qcond=−k(TL−T0)L

Here, TL is the thickness of the wall at complete thickness of the wall and T0 is the temperature of the wall at 0 m .

The expression for the convection heat transfer per unit area is given by,

qconv=k(TL−T∞)

Calculation:

The conduction heat transfer per unit area is calculated as,

qcond=−k( T L − T ∞ )L=−(4.5 W/m⋅K)( 120°C−0°C)0.18 m=−3000 W/m2

The convection heat transfer per unit area is calculated as,

qconv=k(TL−T∞)=30 W/m2⋅K(120°C−20°C)=3000 W/m2

The energy balance equation is calculated as,

qcond−qconv=0−3000 W/m2−3000 W/m2=0−6000 W/m2≠0

The temperature distribution is not possible as the value of conduction and convection heat transfer is not equal.

Conclusion:

Therefore, the temperature distribution is not possible as the conduction and convection heat transfer is not possible.

Answer 8

(b)

To determine

The computation and the plot of the temperature at x=L , T(L) as a function of h for 10≤h≤100 W/m2⋅K along with an explanation of the results.

Answer 9

(b)

To determine

The computation and the plot of the temperature at x=L , T(L) as a function of h for 10≤h≤100 W/m2⋅K along with an explanation of the results.

Answer 10

Expert Solution & Answer

Answer 11

Expert Solution & Answer

Answer 12

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 13

Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - Assume steady-state, one-dimensional conduction in...Ch. 2 - A hot water pipe with outside radius r, has a...Ch. 2 - A spherical shell with inner radius r1 and outer...Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - A composite rod consists of two different...Ch. 2 - A solid, truncated cone serves as a support for a...Ch. 2 - To determine the effect of the temperature...Ch. 2 - A young engineer is asked to design a thermal...Ch. 2 - A one-dimensional plane wall of thickness 2L=100mm...

Solution Summary: The author explains that the temperature distribution is not possible as the conduction and convection heat transfer are not equal.

Concept explainers

Videos

The computation and the plot of the temperature at x=L , T(L) as a function of h for 10≤h≤100 W/m2⋅K along with an explanation of the results.

Want to see the full answer?

Chapter 2 Solutions