
Concept explainers
Solve Prob. 17.11, assuming that the 6 N

(a)
Number of revolutions of gear C.
Answer to Problem 17.12P
Number of revolutions of gear C is
Explanation of Solution
Given information:
Mass of the gear A (mA) = 10kg.
Radius of gyration of the gear A (kA) = 190mm.
Mass of the gear B (mB) = 10kg.
Radius of gyration of the gear B (kB) = 190mm.
Mass of the gear C (mC) = 2.5kg.
Radius of gyration of the gear C (kC) = 80mm.
Initial angular velocity of gear C (Nc)1 = 450rpm
Final angular velocity of gear C (NC)1 = 1800rpm
A couple at gear C (M) = 6N-m.
Radius of gear A (rA) = 250mm
Radius of gear B (rB) = 250mm
Radius of gear C (rC) = 100mm
Calculation:
Moment of inertia of gear A
Moment of inertia of gear B
Moment of inertia of gear C
For Initial condition; angular velocity is 450 rpm
Angular velocity of the gear C,
Gear C mess with Gear A. So angular velocity ration is given as
Gear C mess with gear B
Initial kinetic energy
For final condition; Angular velocity of the gear C is 1800rpm
Gear C mess with Gear A. So angular velocity ration is given as
Gear C mess with gear B
Final kinetic energy
Work done by the gear C
Substitute the value of E1, E2 and W in work energy equation

(b)
Tangential force on gear A.
Answer to Problem 17.12P
Tangential force on gear A is
Explanation of Solution
Given information:
Mass of the gear A (mA) = 10kg.
Radius of gyration of the gear A (kA) = 190mm.
Mass of the gear B (mB) = 10kg.
Radius of gyration of the gear B (kB) = 190mm.
Mass of the gear C (mC) = 2.5kg.
Radius of gyration of the gear C (kC) = 80mm.
Initial angular velocity of gear C (Nc)1 = 450rpm
Final angular velocity of gear C (NC)1 = 1800rpm
A couple at gear C (M) = 6N-m.
Radius of gear A (rA) = 250mm
Radius of gear B (rB) = 250mm
Radius of gear C (rC) = 100mm
Calculation:
Angle of rotation for gear A
Substitute the value of E1, E2 and W in work energy equation for gear A
Want to see more full solutions like this?
Chapter 17 Solutions
VECTOR MECH...,DYNAMICS(LOOSE)-W/ACCESS
- Please sovle this for me and please don't use aiarrow_forwardPlease sovle this for me and please don't use aiarrow_forward3. The cold-drawn AISI 1040 steel bar shown in the figure is subjected to a completely reversed axial load fluctuating between 28 kN in compression to 28 kN in tension. Estimate the fatigue factor of safety based on achieving infinite life (using Goodman line) and the yielding factor of safety. If infinite life is not predicted, estimate the number of cycles to failure. 25 mm + 6-mm D. 10 mmarrow_forward
- CORRECT AND DETAILED SOLUTION WITH FBD ONLY. I WILL UPVOTE 1. The truss shown is supported by hinge at A and cable at E.Given: H = 4m, S = 1.5 m, α = 75⁰, θ = 33⁰.Allowable tensile stress in cable = 64 MPa.Allowable compressive stress in all members = 120 MPaAllowable tensile stress in all members = 180 MPa1.Calculate the maximum permissible P, in kN, if the diameter of the cable is 20 mm.2.If P = 40 kN, calculate the required area (mm2) of member BC.3. If members have solid square section, with dimension 15 mm, calculate the maximum permissible P (kN) based on the allowable strength of member HI.ANSWERS: (1) 45.6 kN; (2) 83.71 mm2; (3) 171.76 kNarrow_forwardCORRECT AND DETAILED SOLUTION WITH FBD ONLY. I WILL UPVOTE 2: A wire 4 meters long is stretched horizontally between points 4 meters apart. The wire is 25 mm2 in cross-section with a modulus of elasticity of 200 GPa. A load W placed at the center of the wire produces a sag Δ.1.Calculate the tension (N) in the wire if sag Δ = 30 mm.2.Calculate the magnitude of W, in N, if sag Δ = 54.3 mm.3. If W is 60 N, what is the sag (in mm)?ANSWERS: (1) 562 N, (2) 100 N, (3) 45.8 Narrow_forwardCORRECT AND DETAILED SOLUTION WITH FBD ONLY. I WILL UPVOTE 4 : A cable and pulley system at D is used to bring a 230-kg pole (ACB) to a vertical position as shown. The cable has tensile force T and is attached at C. The length of the pole is 6.0 m, the outer diameter is d = 140 mm, and the wall thickness t = 12 mm. The pole pivots about a pin at A. The allowable shear stress in the pin is 60 MPa and the allowable bearing stress is 90 MPa. The diameter of the cable is 8 mm.1.Find the minimum diameter (mm) of the pin at A to support the weight of the pole in the position shown.2.Calculate the elongation (mm) of the cable CD.3.Calculate the vertical displacement of point C, in mm.ANSWERS: (1) 6 mm, (2) 1.186 mm, (3) 1.337 mm--arrow_forward
- 1. Derive an expression for H(w) filter or bandpass/reject filter. = for the circuit below. Qualitatively determine if it's a high/lowpass L ell R ww Voarrow_forward2. Obtain the transfer function, H(w) = 0 for the circuit below for R₁ = 1 kQ2, R2 = 10 kQ, and Vi C = 1 μF. What role, if any, does the capacitor play? Explain. R₁ R2 + C + Voarrow_forwardCORRECT AND DETAILED SOLUTION WITH FBD ONLY. I WILL UPVOTE 3 (15 points): A 12-meter-long precast pile segment is to be lifted from a trailer down to the ground and then set in place prior to driving by a crane.1. If two slings are to be used in lifting the pile to the ground, at what distance from the ends must the slings be placed for minimum bending due to its own weight?2. At what distance from the ends must the slings be placed for minimum shear due to its own weight?3. Using one sling to set the pile in a vertical position before driving at what distance from one end must the sling be placed for minimum bending due to its own weight?ANSWERS: (1) 2.48 m, (2) 3.00 m, (3) 3.51 marrow_forward
- International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
