Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 12, Problem 25QLP
What are the benefits and drawbacks to having a pouring temperature that is much higher than the metal’s melting temperature? What are the advantages and disadvantages in having the pouring temperature remain close to the melting temperature?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Suggest the optimum parameter setting or methods to obtain high quality moulded parts.
requirement : a good understandable handwriting and answer in step by step procedure with good arrangement
3) What are the means of elastic and plastic deformations?
List the passageway (gating system) elements in sand casting moulds and show
them with drawing?
Chapter 12 Solutions
Manufacturing Engineering & Technology
Ch. 12 - Why are steels more difficult to cast than cast...Ch. 12 - What is the significance of hot spots in metal...Ch. 12 - What is shrinkage allowance? Machining allowance?Ch. 12 - Explain the reason for drafts in molds.Ch. 12 - Prob. 5RQCh. 12 - What are light castings and where are they used...Ch. 12 - Name the types of cast irons generally available,...Ch. 12 - Comment on your observations regarding Fig. 12.5.Ch. 12 - Describe the difference between a runner and a...Ch. 12 - What is the difference between machining allowance...
Ch. 12 - What is dross? Can it be eliminated?Ch. 12 - Describe your observation concerning the design...Ch. 12 - If you need only a few castings of the same...Ch. 12 - Do you generally agree with the cost ratings in...Ch. 12 - Describe the nature of the design differences...Ch. 12 - Note in Fig. 12.5 that the ductility of some cast...Ch. 12 - Do you think that there will be fewer defects in a...Ch. 12 - Explain the difference in the importance of drafts...Ch. 12 - What type of cast iron would be suitable for...Ch. 12 - Explain the advantages and limitations of sharp...Ch. 12 - Explain why the elastic modulus, E, of gray cast...Ch. 12 - If you were to incorporate lettering or numbers on...Ch. 12 - The general design recommendations for a well in...Ch. 12 - The heavy regions of parts typically are placed in...Ch. 12 - What are the benefits and drawbacks to having a...Ch. 12 - When designing patterns for casting, patternmakers...Ch. 12 - Using the information given in Table 12.2, develop...Ch. 12 - The part in Figure P12.28 is to be cast of 10% Sn...Ch. 12 - Describe the general design considerations...Ch. 12 - Add more examples of applications to those shown...Ch. 12 - Explain how ribs and serrations are helpful in...Ch. 12 - List casting processes that are suitable for...Ch. 12 - Small amounts of slag and dross often persist...Ch. 12 - If you need only a few units of a particular...Ch. 12 - For the cast metal wheel illustrated in Fig....Ch. 12 - Assume that the introduction to this chapter is...Ch. 12 - In Fig. P12.37, the original casting design shown...Ch. 12 - An incorrect and a correct design for casting are...Ch. 12 - Using the method of inscribed circles, shown in...Ch. 12 - A growing trend is the production of patterns and...Ch. 12 - Repeat Problem 12.40 for the case where (a) a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- i need the answer quicklyarrow_forwardWhy the Lead is used in medical devices such as x-ray apparatus? Why the actual size and shape of the cavity must be slightly oversized the product? Why Venting holes and passageways must be built in die casting and not in sand casting?arrow_forward4) List the passageway (gating system) elements in sand casting moulds and show them with drawing? Draw the stress-strain curve and gives the stress and strain equations for both Engineering and True stress-strainarrow_forward
- Converging passage is used for feeding the liquid molten metal into the mould to (a) increase the rate of feeding (b) quickly break off the protruding portion of the casting (c) decrease wastage of cast metal (d) avoid aspiration of airarrow_forwardWhich of these factors causes more porosity to form toward the interior of a casting rather than toward the outside? (a) Gasses are less soluble in the solid metal than the liquid, so solidified areas push dissolved gasses toward the interior. (b) Casting under a vacuum causes gasses near the liquid metal surface to be drawn out of the liquid during solidification. (c) The feeding structures of the mold are designed to force entrapped air into the center of the casting. (d) Draft on the mold wall forces air bubbles toward the interior of the solidifying metal. (e) None of the above Non-eutectic alloys (most commercial alloys) solidify over a temperature range. Which of the following statements explains how this affects the casting process. (a) Solidified non-eutectic alloys are especially difficult to remove from metal dies (b) Non-eutectic alloys have significantly less fluidity than pure metals or eutectic alloys. (c) Non-eutectic alloys solidify starting from the outside of the…arrow_forwardExplain the working of principles of the die casting process which is most preferred of the high production rate?arrow_forward
- Question 3 3.1 Briefly explain the Casting and Molding processes and define their basic requirements. 3.2 If a manufacturer was asked to produce a set of plastic bottles, which method would you suggest? Justify your answer. 3.3 What is the Forging process? Explain the process including two forged products. 3.4 Briefly explain the heat treatment processing techniques using a phase diagram.arrow_forwardEX.3//A cylindrical riser must be designed for a sand-casting mold. The casting itself is a steel rectangular plate with dimensions 7.5 cm x 12.5 cm x 2.0 cm. Previous observations have indicated that the total solidification time (TTs) for this casting =1.6 min. The cylinder for the riser will have a diameter-to-height ratio=1.0. Determine the dimensions of the riser so that its TTS = 2.0 min.arrow_forward2. What do the various elements that comprise the gating system? what are the pouring basin in a sand casting? 3. Explain why a sprue should be tapered? 4. What are the disadvantages of die casting? 5. Explain the various kinds of patterns in use. What are the allowances provided How do the patterns differ from the casting required? 6. Define Expendable-mold, Expendable-pattern Casting Processesarrow_forward
- where are the die cores placed in die casting?arrow_forwardIn sand moulding and casting process, which of the following is the purpose of a chill? a. To increase the rate of heat extraction from the casting b. To reduce the possibility of blow holes O c. To increase the surface finishing of the casting d. To decrease the solidification timearrow_forwardWhy Venting holes and passageways must be built in die casting and not in sand casting? Why the cost of products reduce when increase the quantity? Why the actual size and shape of the cavity must be slightly oversized the product?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Casting Metal: the Basics; Author: Casting the Future;https://www.youtube.com/watch?v=2CIcvB72dmk;License: Standard youtube license