Water flows through a horizontal plastic pipe with a diameter of 0.2 m at a velocity of 11 cm/s. Use the Moody diagram to calculate the power (in mW) lost to friction per meter of pipe. Assume that the water is at 20=C. Hint: The power loss is the product of pressure drop multiplied by volumetric flow rate..

Water flows through a horizontal plastic pipe with a diameter of 0.2 m at a velocity of 11 cm/s. Use the Moody diagram to calculate the power (in mW) lost to friction per meter of pipe. Assume that the water is at 20=C. Hint: The power loss is the product of pressure drop multiplied by volumetric flow rate..

Understanding Business

12th Edition

ISBN:9781259929434

Author:William Nickels

Publisher:William Nickels

Chapter1: Taking Risks And Making Profits Within The Dynamic Business Environment

Section: Chapter Questions

Problem 1CE

See similar textbooks

Similar questions

typing
Consider a 10-m-long smooth rectangular tube, with a = 50 mm and b = 25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.017 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C. (Nu = 3.39) °C
Water flows at 2 m/s through a 2.5 m length of a 25 mm inside diameter tube. The inlet temperature of water is 293 K and its outlet temperature is 295 K. Assume that the inside surface temperature of the tube is at 320 K. Determine the overall heat transfer coefficient (based on the inside surface area) in kW/m^2·deg C. A. 1.61 B. 2.55 C. 1.09 D. 7.85 do fast i will 6 upvotes.
The following is the temperature control system of a heat exchanger. a)Identify the type of system. b) Calculate the steady state error when it is subjected to an input. r(t) = 2 c) Calculate the steady state error when subjected to an input. r(t) = 3t R(s) 15 C(s) 5³ - 5²² + 5s
Output from a process contains 0.02 defective unit. Defective units that go undetected into final assemblies cost $25 each to replace. An inspection process, which would detect and remove all defectives, can be established to test these units. However, the inspector, who can test 20 units per hour, is paid $8 per hour, including fringe benefits. Should an inspection station be established to test all units? Assume that the line will operate at the same rate (i.e., the current production rate) regardless of whether or not the inspection operation is added. a-1. Without the inspector, what is the current hourly cost of defects? a-2. Should an inspection station be established to test all units based on costs alone? multiple choice Yes No a-3. If the inspection operation is added, what would be the cost to inspect each unit? Note: Round your answer to 2 decimal places. b. What would be the benefit (or loss) from establishing the inspection process? Note: Round your answer…
Inlet pressure P₀= 700 kPa, inlet temperature T₀ = 311 K. Since the temperature To minimum cross-sectional area Aₘᵢₙ= 12 cm² outlet pressure Pₑ=448 kPa, outlet cross - sectional area Aₑ = 20 cm² What is the value of the area where the shock wave occurs?
. Mary and Tom operate a lemonade stand. They are concerned that the lemonade doesnot taste fresh at the end of the day. Which of the following variables is an environmental variable in their operation?a. The temperature of the lemonade when they take it out of their refrigerator in themorningb. The temperature of the air during the dayc. The temperature of the lemonaded. The temperature of the water used to make the lemonade
While analyzing their annual sales data (liters of wine sold per year) for the past 30 years, a vineyard found that after taking four successive differences, the resulting data had a mean of 2458 liters and looked like a stationary process (e.g. white noise). If the actual data for the past four years were 2018 - 2134 liters, 2017 - 2403 liters, 2016 - 2076 liters, and 2015 - 2290 liters. What would be a reasonable forecast for sales in 2019? Explain.
2. A beverage company would like to use a mean chart to monitor how much liquid beverage it puts into each 500-ml bottle. They know from experience that whenever this process is under control, bottle weight is normally distributed with a mean of 500 ml and a standard deviation of 2 ml. The company plans to measure samples of 30 bottles from the production lineevery hour and record the mean weight of liquid beverage in the bottles. If the company uses z = 3 as its standard for establishing the mean chart, where will the upper and lower control limits be on the chart? (Noteshaper: Scenario #28)
The K of a proportional controller is 30 and the reference value is 50% of the output. A valve is used at its outlet that, for the reference value, allows a flow of 2.0 m?/s. The valve changes its output in direct proportion to the controller output. What will be the controller output and deviation in error when the flow is to change to 2.5 m/s?
Output from a process contains 0.01 proportion of defective units. Defective units that go undetected into final assemblies cost $26 each to replace. An inspection process, which would detect and remove all defectives, can be established to test these units. The inspector, who can test 21 units per hour (which matches the current production rate), would be paid $9 per hour, including fringe benefits. Assume that the line will operate at the same rate (i.e., the current production rate) regardless of whether or not the inspection operation is added. A. Without the inspector, what is the current hourly cost of defects? (Round your answer to 2 decimal places.) B. If the inspection operation is added, what would be the cost to inspect each unit? (Round your answer to 2 decimal places.) C. What would be the benefit (or loss) from establishing the inspection process per unit? (Input the amount as a positive value. Round your answer to 2 decimal places.)
Meena Chavan Corp.’s computer chip production process yields DRAM chips with an average life of 1,800hours and s = 100 hours. The tolerance upper and lowerspecification limits are 2,400 hours and 1,600 hours, respectively. Is this process capable of producing DRAM chips tospecification?