Question 2) In the system given in the figure, a distributed load of w=76 kN/m acts on the rod AB of L=3 m length . The angle 8 that the bar BC makes with the horizontal is 0=57 ° . The normal stress allowed for the bar BC is o m = 245 MPa and the allowable shear stress for the pins at points A and B is Tm = 73 MPa. Bar BC has a rectangular section and the side length a of the section is given as a=27 mm . According to this; 0° L B w (kN/m) Question 2-A) Find the smallest b side length required for the bar section BC .(Write your result in mm.) Response: Question 2-B) The connection type at point B is given in the figure next to it. Accordingly, find the smallest diameter required for pin B. ( Write your result in mm.) Response:

Question 2) In the system given in the figure, a distributed load of w=76 kN/m acts on the rod AB of L=3 m length . The angle 8 that the bar BC makes with the horizontal is 0=57 ° . The normal stress allowed for the bar BC is o m = 245 MPa and the allowable shear stress for the pins at points A and B is Tm = 73 MPa. Bar BC has a rectangular section and the side length a of the section is given as a=27 mm . According to this; 0° L B w (kN/m) Question 2-A) Find the smallest b side length required for the bar section BC .(Write your result in mm.) Response: Question 2-B) The connection type at point B is given in the figure next to it. Accordingly, find the smallest diameter required for pin B. ( Write your result in mm.) Response:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross-sectional area of 400 mm Eal = 70 GPa. |800 kN/m +100 mm -100 mm A B 125 mm I800 kN/m Answer: 0A = 0c = 189 MPa, oB 21.4 MPа
Two identical plates are connected by two 18-mm diameter rivets as shown. Consider the following dimensions: B = 200 mm t = 22 mm x = 16 mm The allowable stresses of the plate are the following: Normal stress = 18 MPa Bearing stress = 4 MPa Shearing stress = 5 MPa Determine the maximum force P: A. Considering the normal stress: P = B. Considering the bearing stress: P = C. Considering the shearing stress: P = Express your answers in three decimal places. KN kN KN O CHEGG.CO ISL STRI NG URVE VARSITY TUTUP INST UTORIAL TE SUCH, B O CHEGG COURSEHERO, SKOOLI TUTORET TUTURME VARSITY TUTORS, WZANT. ETC. DISTRIBUTION TO ANY PARTY IS PROHIBITED, INSTITUTIONAL EXAM NOT EUPLOADING ON ANY TUTORIAL SITE SUCH LEDO CHEGG, COURSEHERO, SKOTTOREYZ TUTORM VARSITY TUTORS, W ZAWI, ETC. P4 DISTRIBUTION TO ANY PARTY IS PROHIBITED. NOT P SN INSTITUTIONAL EXEM NOT FOR REUPLNG ON ANY TUTORIAL SITE SUC 30 CHEGG, COURSEHERO, SKOOL TUTO+STORM VARSITY TUTORS, W DISTRIBUTION TO ANY RTY IS PROHIBITED. THERO, SKOOL…
The wide-flange pinned-end column shown in the figure carries two loads, a force acting at the centroid P₁ = 450kN and a force P₂ = 270kN acting at distance s = 100 mm, from the centroid. The column is an HE 240B shape with L = 4.2m, E = 200 GPa, and Oy = 290 MPa. (a) What is the maximum compressive stress in the column?
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torqueT that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that dị 30mm and d2 = 50mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC. 125 kN 60 kN 125 kN 0.9 m 1.2 m
A wooden frame shown below is supported by a tie rod CF and a pin support at A. The diameter of the tie rod CF is 30 mm, and the cross-sectional area of member BD is 900 mm?. The diameters of the pins at A and D are 8 mm and 12 mm, respectively, and each pin is subjected to double shear. If the weight of the bucket hanging from end E is 3 kN, determine (a) The axial stresses in tie rod CF and member BD. (b) The shear stresses in pins A and D. - 0.6 m-0.6 m→ D E 0.6 m V30B 1.2 m F
Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A B F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.
2. Member AB shown in the figure supports a 5 N/mm uniformly distributed load and 4kN concentrated load as shown in the figure. Determine the position x of these loads so that the average tensile stress in the tie rod AC is equal to 90% of the compressive stress at the smooth support B. The rod has a diameter of 19 mm and the contact area at is 700mm². (Hint: quadratic formula) B A X 5 N/mm 4 kN 300mm B
For the beam shown: 1. Draw the free-body diagram (FBD) and determine the reactions at the supports. 2. Determine the internal forces and draw their diagrams. 3. Design the beam using IPE shape. 4. Draw the stress diagram in the critical cross section. Data: F= 60 kNm, L = 1 m, 0 = 120 MPa. I IPE A F L #C L B
4. Two solid shafts of different materials are rigidly fastened together and attached to rigid supports as shown in the figure together with the given section properties. The torque of 1000 N-m is applied at the junction of the two segments. Compute the maximum shearing stress developed in the assembly. Answer: TĄ = 5.57 MPa Ts = 22.0 MPa 3 m 1.5 m Ta Aluminum Steel 75 mm dia. T=1.0 kN•m Ga- 28 GN/m²? 50 mm dia G, - 83 GN/m?
Radius of the pin at C is 3mm. While at static equilibrium, we know that a force P of magnitude 500 N is applied to the pedal shown, calculate (a) The average shearing stress in the pin at C (b) the corresponding bearing stress in the pedal at C, (c) the corresponding bearing stress in each support bracket at C. 9 mm T 5 mm C A 75 mm 125 mm B 300 mm PI D