The rod has a diameter of 40 mm. It is subjected to the force system Fx=1300 N=1300 N, Fy=500 N=500 N, Fz=800 N=800 N. Determine the normal stress that acts at point B. Determine the shear stress (τB)xy that acts at point B. Determine the shear stress (τB)xz that acts at point B.

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Eigure 6)…

A: So angle is clockwise and θ=-30°σx=31ksiσy=-38ksiτxy=0

Q: If the output torque on the CD shaft is T ́ = 75 N-m and the motor rotates at 175 rpm, determine the…

A: Given for CD shaft    diameter d2=35 mm, radius of gear R2=125 mmand torque T2=75 N-mfor EA shaft…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Take di = 30 mm,…

A: Determine the average normal stress at the midsection of rod BC.

Q: 300 mm is applied to the bell crank. B -450 mm- (a) Determine the normal stress developed in e 10mm…

A:

Q: The rectangular bar has a width of w= 2.75 in. and a thickness of t = 2.00 in. The normal stress on…

A: Given : W = 2/75 in. t = 2.00 in Normal stress on plane AB of the rectangular block is 6ksi

Q: (2) A square member (400mm x 400mm) sustains an internal shear force of 150 kN and an internal…

A: Given: A square cross section of 400mm × 400mm Shear force = 150KN Bending moment = 250KN-m…

Q: The 2 D stress at a point is given by the matrix Txy 50 15 MPa. The maximum 15 10 6. II = Tyx yy…

A: To Find :The max shear stress ?

Q: Two forces P1 and P2, of magnitude P1 = 15 kN and P2 = 18 kN, are applied as shown to the end A of…

A: Given:P1=15 kN     =15000 NP2=18 kN     =18000 NRadius c=20 mmThe axial force and bending moment…

Q: A 80 MPa 30° B 30 MPa 40 MPa

A:

Q: a b 45 MPa 60° a

A: Given: Shear stress  To find: Normal stress and principal stress on inclined plane

Q: Q1. C The solid 100-mm-diameter steel cantilever shaft shown in Fig. 1 is subjected to an axial…

A: To determine  The state of stress at point A Principal stresses and shear stress FOS from maximum…

Q: 1) The copper pipe below has an outer diameter of 50 mm, inner diameter of 30 mm, and G = 45 GPa. It…

A:

Q: The couple M = 78 kip-in. is app section shown in a plane formin vertical. Determine the stress at…

A:

Q: 3. b) The state of stress at a point is shown on the element. Using Mohr's cicle, determine The…

A:

Q: The solid 1.25-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

A:

Q: mine the maximum shear stress for the 7.. 3₁ == 0 MPa Txy=-31 Ox=37

A:

Q: Cylinder of height 2H. radius R. centroid at (0,0.H), axis e3 undergoes deformation x = o(z) = z +…

A:

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

A:

Q: Problem 5: The stresses on the x-y-axes are o, = 8 ksi, o, = 12 ksi, and Ty = -5 ksi. Draw the…

A:

Q: The d - 16-mm-diameter solid rod passes through a D=21-mm-diameter hole in the support plate. When a…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.