Q.2) The right figure show thecantilever beam and loading,while the left figure show thecross-sectional dimensions of the100 mm8 mm4 kN0.5 mshape. Find:100 mm(a) The largest verticalshearing stress in thebeam.(b) The maximum bending6 kN0.5 m6 mm3 kNstress.0.5 mHint: Rotate the cantilever beam 90° CW and solvenormally (x-axis become horizontal).

Solution:- 1. Shear stress in the beam:

100 mm Q.2) The right figure show the cantilever beam and loading, while the left figure show the cross-sectional dimensions of the 8 mm 4 kN 0.5 m shape. Find: (a) The largest vertical shearing stress in the beam. 100 mm 6 kN 0.5 m - 6 mm (b) The maximum bending 3 kN stress. 0.5 m Hint: Rotate the cantilever beam 90° CW and solve normally (x-axis become horizontal).

100 mm Q.2) The right figure show the cantilever beam and loading, while the left figure show the cross-sectional dimensions of the 8 mm 4 kN 0.5 m shape. Find: (a) The largest vertical shearing stress in the beam. 100 mm 6 kN 0.5 m - 6 mm (b) The maximum bending 3 kN stress. 0.5 m Hint: Rotate the cantilever beam 90° CW and solve normally (x-axis become horizontal).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1.1 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d₁ = 30 mm and d₂ = 50 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC. d₂ 125 kN B 60 kN 125 kN 1.2 m 0,9 m
2. Determine the internal forces and draw the diagrams
The steel tube seen below has an outer diameter do = 60mm and an inner diameter d, = 50mm. It is subjected simultaneously to torque T = 1.5kN-m and to axial load P = 205kN. Determine: (a) the maximum in-plane shear stress and its orientation, (b) the associated normal stress and (c) sketch both on a properly oriented element.
Pls show complete solution and fbd
A cantilever beam AB is loaded as shown in the Cross-section of the beam figure and the beam is supported with a cable BD. The beam's cross-section is rectangular as shown. It is known that the tension force in cable BD is 10.39 kN. Calculate the normal stress at point a, and calculate the shear stress at point c. Ignore the weight of the beam. 10cm 10cm +15cm+ 75cm B F-13.99KN 30cm 60cm 90cm
Solve it correctly
The frame supports the distributed load shown. Determine the state of stress acting at points E and D. Show the results on a differential element at this point. 4 kN/m DA -1.5m-15m+ 3 m 1 BA 20 mm 60 mm 20 mm. 5m T D 50 mm
A solid circular bronze [G = 6,500 ksi] shaft, 6.0 ft long and 1.325 in. in diameter, carries a torque of 90 Ib-ft. For this shaft, determine: (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax = psi (b) Ф%3D
Problem 6 For the structure shown in the figure, determine the normal and shear stresses at point A on the cross section of the pipe. at section a-a. mun 40 mm 300 mm 300 mm
In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.1 ksi, If t 1.9 in. and b= 3.8 in., 3 in. a. determine the largest P, which is vertical, the frame can 3 in. carry 30 b. determine the largest P, which is normal to AC, the frame can carry