Answered: A square bar carries a series of loads…

A square bar carries a series of loads as shown in Figure P1-47. Compute the stress in each segment of the bar. All loads act along the central axis of 1-47. the bar.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum compressive bending stresses in the beam shown. Let P = 14 Note Answer in whole number I = 100 × 106 mm P kN/m 2. 130 mm A NA- B |= 4P 6 m Poy= 200 mm 2P kN 6 -X= 4m - 4P - GP
Determine the length L of the center portion of the rectangular bar so that the maximum bending stress at A, B and C is the same. The bar has a thickness of 10 mm. 40mm ↓ 200mm 350N 60mm A C L/2 L/2 B 40mm 200mm
The bars of the truss each have a cross-sectional area of 1.92 in². Determine the average normal stress in ksi in member BD due to the loading P = 10 kips. NOTE: use absolute value for Normal stress. The final answer should have 2 decimal places where: L1 =3.8 ft. L2 = 4.3 ft. B L1 D L2 E 0.75 P L2
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A₁ = 350 mm² and a length of L₁ = 2.1 m. Rod (2) has an area of A₂ = 375 mm² and a length of L₂ = 1.5 m. Assume dimensions of a = 3.2 m, b = 1.1 m, and c = 1.4 m. After a load of P = 130 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) a L2 Rigid bar L₁ Answer: (a) σ₁ = i 02= i (b) VD= i (1) B MPa MPa mm -X,U b C ↓ С D P
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 340 mm2 and a length of L1 = 3.6 m. Rod (2) has an area of A2 = 315 mm2 and a length of L2 = 1.2 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 60 kN is applied to the rigid bar at D, determine:(a) the normal stresses in rods (1) and (2)(b) the magnitude of the downward deflection of the rigid bar at D.
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 410 mm2 and a length of L1 = 3.2 m. Rod (2) has an area of A2 = 355 mm2 and a length of L2 = 1.3 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 50 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) L2 a B C D x,u Rigid bar |(1) Answer: (a) o1 = i MPa 02 = i MPa (b) VD = i mm
Determine the normal stress in members BD, AC, and BCin the truss shown. The cross-sectional area of each member is 1500mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value.
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 3.7 in.². Assume a = 4.75 ft and b = 5.70 ft. If the normal stress in each member must not exceed 60 ksi, determine the maximum load Pmax that may be supported by the structure. a D Answer: Pmax = i b B E b kips P
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
A pin-jointed truss ABC shown below consists of two links AB and BC. These links are 6 mm thick and 20 mm wide as shown. There are support brackets at A and C. All pins are 12 mm in diameter and a vertical force, P = 9 kN is applied at pin B as shown. The angle 0 =38 deg. and the angle ẞ = 0 + 20 deg. The normal stress in link AB is (The result is accurate to one decimal place, in the unit MPa. Please write down only the value of your final result) · 12mm 9 20mm -1.0m⋅ B
For the truss shown and loading, determine the axial stress in member BH in ksi. Use two decimal places. Express your answer in absolute value. Assume the sectional areas of the following: Top and bottom members = 1.80 in² Web members = 0.90 in² B 20 kip с 40 kip 6 ft @ 4 = 24 ft D 6 ft
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. C D I-KE -1.2 m-1.2 m 1.2 m B