A cantilever beam AB is loaded as shown in theCross-section of the beamfigure and the beam is supported with a cable BD.The beam's cross-section is rectangular as shown.It is known that the tension force in cable BD is10.39 kN. Calculate the normal stress at point a,and calculate the shear stress at point c. Ignore theweight of the beam.10cm10cm+15cm+75cmBF-13.99KN30cm60cm90cm

solution- Free body Diagram (FBD)- sinθ =75195cos θ = 180195

ever beam AB is loaded as shown in the ure and the beam is supported with a cable BD. me beam's cross-section is rectangular as shown. is known that the tension force in cable BD is 0.39 kN. Calculate the normal stress at point a, and calculate the shear stress at point c. Ignore the weight of the beam. 75cm D 30cm Cross-section of the beam 10cm 60cm + c 10cm a +15cm+ E F-13.99kN B

ever beam AB is loaded as shown in the ure and the beam is supported with a cable BD. me beam's cross-section is rectangular as shown. is known that the tension force in cable BD is 0.39 kN. Calculate the normal stress at point a, and calculate the shear stress at point c. Ignore the weight of the beam. 75cm D 30cm Cross-section of the beam 10cm 60cm + c 10cm a +15cm+ E F-13.99kN B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Mechanics. help asap pls
Two steel plates are welded together to form an inverted T-beam and are loaded as shown below. Determine the maximum bending stress developed. Also, determine the maximum shear stress at the neutral axis of the cross section. The following Inte Av = 9K Bv = 11K location of centroid = 3.56" above X-Ref Shear diagram Moment diagram 1" x 10" steel plate 1" x 8" steel plate X-reference A 6' 8K 12' 24' 12K 6' B of your work is accurate. Yo ment Mmax = 66K' Vmax 11K Moment of Inertia = 218 inª
A simply supported beam has a maximum moment equal to 20 KN.m. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. What is the actual bending stress of the beam in MPa? Blank 1 (use two decimal places, no need for unit)\\ with complete solution
*9-56. The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T each member when T, = 45 °C. Also, how far will the collar be displaced? The cross-sectional area of each member is 1130 mm². 10 °C, determine the average normal stress in and the d LA B C. ave firs T | 0 T S brs loota dA 0.6 m 1 m
1-50. The plastic block is subjected to an axial compressive force of 600 N. Assuming that the caps at the top and bottom distribute the load uniformly throughout the block, determine the average normal and average shear stress acting along section a-a. 600 N 30° 50 mm 50 mm 600 N 150 mm 50 mm
A square box beam is made of two 20X80-mm planks and two 20X120-mm planks nailed together as shown. We know that the spacing be- tween the nails is s=50 mm and that the allowable shearing force in each nail is 300 N, calculate (a) the largest allowable vertical shear in the beam, (b) the corresponding maximum shearing stress in the beam. E 20 mm 80 mm 20 mm S 120 mm S
= BA The solid steel shaft carries the torques T₁ 750 N-m and T₂ 1200 N-m. Using L₁ L2 2.5 m and G-83 GPa, determine the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 40. (Hint: Analyze for 0 governs and T governs). Odmin 54.1 mm = Odmin 46.7 mm B Odmin = 51.9 mm Odmin 26.0 mm 7₁ B C 1₂
STRENGTH OF MATERIALS answer: 13.8 MN/m2, 5.94 cm from tip of T Please show the solution
Show complete solution - Given, Required, Solution. (another solution pls)
Question 3 A compressive force of 45 kN acts parallel to the longitudinal axis of the I-section as shown in Figure 3 below and in the position indicated. Calculate the stress at point A, B, C and D due to the load. -150- y A B D -35- 45 KN
7. (c) A load P of 5000 Kg on the crank pin of the crank shaft as shown in figure is required to turn the shaft at constant speed. The crank shaft is made of ductile steel having yield strength of 2800 Kg/cm2 as determined in simple tensile test. Calculate the diameter of the shaft based on a factor of safety of 2.5. Use maximum shear stress theory. Consider section m-n as critical section. 'm 20cm P 15cm
In the figure it is holding the BCD rod, the AC rod suspended. The cross section of the AC rod is 15 x 8 mm2. 1.6 tons of force is applied to the BCD rod at point D. C pin is single acting and its diameter is 10 mm. According to this; Find the shear stress at the pin and the bedding stress on the AC rod.