Q4 - For the given beam and cross section, at point B on section A-A (mid-span), determine the followings and show them on a differential element. a) Principal stresses and its orientation b) Maximum in-plane shear stress and its orientation

Q4 - For the given beam and cross section, at point B on section A-A (mid-span), determine the followings and show them on a differential element. a) Principal stresses and its orientation b) Maximum in-plane shear stress and its orientation

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SOLVE THE PROBLEM USING DOUBLE INTEGRATION METHOD Problem II. The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminum rod. Find the maximum allowable value of the applied force P if the stress in the rod is not to exceed 120 MPa. Use Est = 200 GPa, I = 50 x 10 mm4 for the beam, Eal = 70 GPa, and A = 42 mm² for the rod. 5 m 2 m Aluminum -Steel 2 m C
The couple M is applied to a beam of the cross section shown in a plane forming an angle b with the vertical. Determine the stress at (a) point A, (b) point B, (c) point D. Determine the neutral axes.
Determine the maximum compressive bending stresses in the beam shown. Let P = 16
Question 5 Match the answers in the columns. v Maximum Shear stress of a cross section. A. using an l-section instead of a rectangular section. v Maximum Bending stress of a cross section. B. Tension and bending force. C. 1m form the supports - v If a simply supported beam is subjected to a distributed load, where are you most likely to find tension bending cracks. D. At Midspan - v Ifa simply supported beam is subjected to a distributed load, where are you most likely to find shear cracks. E. Midspan at the bottom v The bending stress in a section can be reduced by using a F. Midspan at the top v Shear stress can be increased by the width of a section. G. At the supports. v The shear force in fasteners. H. Reducing the width of a section. v Moment couple on a section. 1. using a rectangular section instead of an l-section J. Shear flow K. Increasing the width of a section. L. Only at the section sides touching the NA M. In between the NA and the top/bottom fibres N. Usually at the NA…
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
The state of stress at a point in a member is shown on the element. Determine the principal normal stresses and their orientation and the maximum in-plane shear stress and their orientation. Draw Mohr’'s circle and Show results on properly oriented elements. -60 30 -50 40 -40 T-30 30 30 -20 40 30 -10 -60 -50 -40 -30 -20 -10 30 40 50 10 20 бо 10 20 30 40 50 60
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
Consider a cantilevered beam which is made of two identical. rectangular sections, a force P is applied at free end. 11) if A and B are not clued together, determine the bending stress distribution at a-a cross section, draw o Chint: each section carries P/ and label the Tout at the outest fibers. * 0.5m a 12) if we weld the two A & B together along the member length. determine the bending stress distribution, draw and laber. m ✓ P=1kw A 181- дет B зст
If the beam is subjected to a bending moment of M = 5 kN # m, determine the bending stress developed at point A and sketch the result on a differential element at this point.
The hollow circular beam is fixed to the wall (with a bracket) on the left and has an end-cap on the right. The cross-section is shown. (a) Determine state of stress at point A & draw the stress element (b) Determine state of stress at point B & draw the stress element A 100 k-in Tout 2 in n=1.75 in В. B 40 k-in C Tout 30 k X